The short answer: a data interpretation question is a reading task followed by a small calculation. Read the title and units first, pick only the figures the question needs, and then use percentage change, ratio, average or difference. A bar chart is a table drawn with bars, so you can rewrite it as one.
The sample data
A factory makes two products, P and Q. The table gives units produced (in hundreds) in each quarter of a year. The data is made up for practice.
| Quarter | Product P | Product Q |
|---|---|---|
| Q1 | 120 | 150 |
| Q2 | 135 | 140 |
| Q3 | 150 | 165 |
| Q4 | 165 | 180 |
Question 1: percentage increase
By what percentage did the production of P rise from Q1 to Q4? Change = 165 − 120 = 45. Percentage = 45 ÷ 120 × 100 = 37.5%. The base is always the earlier figure, 120, not 165.
Question 2: ratio of totals
What is the ratio of the total production of P to that of Q? P = 120 + 135 + 150 + 165 = 570. Q = 150 + 140 + 165 + 180 = 635. Ratio = 570 : 635. Both are divisible by 5, giving 114 : 127. It cannot be reduced further, since 114 = 2 × 3 × 19 and 127 is prime.
Question 3: greatest difference
In which quarter was the gap between Q and P largest? The gaps are Q1: 30, Q2: 5, Q3: 15, Q4: 15. The largest is in Q1. You do not need to calculate percentages here; a plain difference answers it.
Question 4: share of a total
In Q4, P was what percentage of the total production of the two products? Total = 165 + 180 = 345. Share = 165 ÷ 345 × 100 = 11/23 × 100, which is about 47.8%. As a check, P is a little less than half, so the answer should sit just below 50%.
A method that works on any chart
- Read the heading, the units and the legend. 'In thousands' or 'in crores' changes every answer.
- Underline what is asked: the year, the product, change or share.
- Copy the numbers you need into a small table on your sheet.
- Choose the formula: change ÷ old, part ÷ whole, total ÷ count.
- Estimate the answer first, then calculate, and see whether they agree.
Bar charts and line graphs
On a bar chart, read the value from the scale, not by looking at the height of bars. Check where the axis starts. If it does not start at zero, one bar that looks twice as tall may not be twice the value. In a stacked bar, the top segment's value is its own length, not the height of the whole bar.
Reading a bar chart with two series
Suppose the table above were drawn as a bar chart with two bars per quarter. To answer Question 3 you would read the heights of the P and Q bars against the scale and subtract. Before calculating, write the eight values in a small table like the one above. This takes ten seconds and prevents the commonest error, reading P's value from Q's bar.
Traps
- Using the wrong base: percentage increase uses the old value; percentage of the total uses the total.
- Mixing percentage with percentage points. A fall from 40% to 30% is 10 percentage points, but 25% in relative terms.
- Ignoring units in a question such as 'in lakhs' or 'per 1,000'.
- Rounding too early and drifting to a wrong option.
Course · Beginner · Free
Quantitative Aptitude — Data Interpretation: Foundation
Foundation course on Data Interpretation (Quantitative Aptitude): the basics, explained from the start.
Practise data interpretation sets under a timer.
Take a practice testFrequently asked questions
What topics do data interpretation questions need?
Mostly percentage, ratio, average and simple calculation. Sets can also use profit and loss or growth rates.
How do I save time on a DI set?
Do the easy questions first, skip questions that need long calculation, and use approximation when the options are far apart.
What is the difference between a table and a bar chart question?
The calculation is the same. A bar chart adds the step of reading values from a scale.
How do I calculate the average from a table?
Add the values and divide by how many there are. For Q's production above, 635 ÷ 4 = 158.75.
Can I improve at DI quickly?
Learn squares up to 30 and common fractions as percentages, such as 1/8 = 12.5%, so that calculation does not slow you down.