Chemistry practice for Joint CSIR-UGC National Eligibility Test

50 practice questions on what the checked Joint CSIR-UGC National Eligibility Test syllabus lists under Chemistry. Each has its answer and explanation. If an answer looks wrong, please tell us.

Which balanced equation shows the incomplete combustion of methane forming carbon monoxide?

  1. 2CH4 + 3O2 → 2CO + 4H2O
  2. CH4 + 2O2 → CO2 + 2H2O
  3. CH4 + O2 → CO + H2O
  4. 2CH4 + O2 → 2CO + 2H2O
Answer and explanation

Answer: A

Check atoms: left 2 C, 8 H, 6 O; right 2 C, 8 H, 2 + 4 = 6 O. Balanced. CH4 + 2O2 → CO2 + 2H2O is complete combustion; CH4 + O2 → CO + H2O and 2CH4 + O2 → 2CO + 2H2O do not balance.

3 kg of a fuel on complete combustion releases 1,35,000 kJ. Its calorific value is:

  1. 45,000 kJ/kg
  2. 4,05,000 kJ/kg
  3. 15,000 kJ/kg
  4. 40,500 kJ/kg
Answer and explanation

Answer: A

Calorific value = 1,35,000 ÷ 3 = 45,000 kJ/kg. Multiplying instead of dividing gives the wrong answer 4,05,000 kJ/kg.

Which set contains only amphoteric oxides?

  1. Al2O3, ZnO, BeO
  2. Na2O, MgO, BaO
  3. SO3, P4O10, Cl2O7
  4. CO, NO, N2O
Answer and explanation

Answer: A

Al2O3, ZnO and BeO react with both acids and bases. Na2O, MgO and BaO are basic, SO3, P4O10 and Cl2O7 acidic, and CO, NO and N2O neutral.

Nylon-2–nylon-6 is formed from

  1. glycine and aminocaproic acid
  2. 3-hydroxybutanoic acid and 3-hydroxypentanoic acid
  3. adipic acid and hexamethylenediamine
  4. caprolactam alone
Answer and explanation

Answer: A

Nylon-2–nylon-6 is a biodegradable polyamide of glycine and aminocaproic acid. 3-hydroxybutanoic and 3-hydroxypentanoic acids give PHBV, adipic acid and hexamethylenediamine give nylon-6,6, and caprolactam alone gives nylon-6.

Which reaction temporarily ends a chlorine chain in the stratosphere?

  1. Cl + O₃ → ClO + O₂
  2. Cl + CH₄ → HCl + CH₃
  3. ClO + O → Cl + O₂
  4. CF₂Cl₂ → CF₂Cl + Cl
Answer and explanation

Answer: B

Forming HCl locks chlorine into a reservoir. Cl + O₃ → ClO + O₂ and ClO + O → Cl + O₂ are chain steps; CF₂Cl₂ → CF₂Cl + Cl starts a chain.

Mixing solutions of which pair gives a precipitate?

  1. NaCl and KNO3
  2. NaNO3 and KCl
  3. HCl and NaOH
  4. AgNO3 and KCl
Answer and explanation

Answer: D

AgNO3 + KCl → AgCl + KNO3; silver chloride is insoluble. With NaCl and KNO3, or NaNO3 and KCl, all possible products are soluble, and HCl with NaOH only forms water and soluble NaCl.

Which of these is a disproportionation reaction?

  1. 2H2O2 → 2H2O + O2
  2. NaOH + HCl → NaCl + H2O
  3. CaCO3 → CaO + CO2
  4. Zn + 2HCl → ZnCl2 + H2
Answer and explanation

Answer: A

In H2O2 oxygen is −1; it becomes −2 in H2O and 0 in O2, so the same element is both reduced and oxidised. NaOH + HCl and the decomposition of CaCO3 involve no change in oxidation number; Zn + 2HCl is redox between two different elements.

What is the anode reaction of the lead storage battery on discharge?

  1. PbO2 + 4H+ + SO4 2- + 2e- gives PbSO4 + 2H2O
  2. 2H2O gives O2 + 4H+ + 4e-
  3. Pb2+ + 2e- gives Pb
  4. Pb + SO4 2- gives PbSO4 + 2e-
Answer and explanation

Answer: D

Lead is oxidised at the anode to PbSO4. PbO2 + 4H+ + SO4 2- + 2e- gives PbSO4 + 2H2O is the cathode reaction.

Equal volumes of water with 81 mg/L Ca(HCO3)2 and water with 111 mg/L CaCl2 are mixed. The permanent hardness of the mixture is:

  1. 100 ppm
  2. 25 ppm
  3. 75 ppm
  4. 50 ppm
Answer and explanation

Answer: D

CaCl2 gives 100 ppm as CaCO3; after mixing equal volumes it is halved to 50 ppm.

A softener treats 3000 L/h of 200 ppm water for 10 hours. The hardness removed (as CaCO3) is:

  1. 600 g
  2. 60 kg
  3. 6.0 kg
  4. 600 kg
Answer and explanation

Answer: C

Volume = 30,000 L; hardness = 200 mg/L × 30,000 L = 6,000,000 mg = 6.0 kg.

An effluent has COD 160 mg/L and BOD 120 mg/L. The BOD/COD ratio is:

  1. 0.75
  2. 1.33
  3. 0.25
  4. 0.50
Answer and explanation

Answer: A

120 ÷ 160 = 0.75, which means that most of the organic matter is biodegradable. The ratio cannot exceed 1.

The volume of 0.01 M EDTA needed by 50 mL of the same water (200 ppm) is:

  1. 5 mL
  2. 20 mL
  3. 2 mL
  4. 10 mL
Answer and explanation

Answer: D

Hardness in 50 mL = 10 mg CaCO3 = 0.10 mmol; EDTA volume = 0.10 ÷ 0.01 = 10 mL.

5000 L of the water (200 ppm total hardness) is softened by sodium zeolite. The salt needed to regenerate the bed is:

  1. 1.00 kg
  2. 1.17 kg
  3. 2.34 kg
  4. 0.585 kg
Answer and explanation

Answer: B

Hardness removed = 200 × 5000 = 1,000,000 mg = 1.0 kg as CaCO3; NaCl = 1.0 × 117 ÷ 100 = 1.17 kg.

For the same water, the pure soda needed per litre is:

  1. 53 mg
  2. 159 mg
  3. 106 mg
  4. 212 mg
Answer and explanation

Answer: C

Soda = 1.06 × (50 + 50) = 106 mg per litre.

For the water analysed above (temporary Ca 50, temporary Mg 50, permanent Ca 50, permanent Mg 50 ppm), the pure lime needed per litre is:

  1. 148 mg
  2. 74 mg
  3. 111 mg
  4. 200 mg
Answer and explanation

Answer: A

Lime = 0.74 × (50 + 2 × 50 + 50) = 0.74 × 200 = 148 mg per litre.

A water has total hardness 120 ppm and alkalinity 200 ppm (all HCO3−). Its non-carbonate hardness is:

  1. 0 ppm
  2. 80 ppm
  3. 120 ppm
  4. 200 ppm
Answer and explanation

Answer: A

Alkalinity exceeds hardness, so all of the hardness is carbonate hardness and the non-carbonate hardness is zero.

A 100 mL sample needs 5.0 mL of 0.02 N HCl to the phenolphthalein end point. P in ppm of CaCO3 is:

  1. 25 ppm
  2. 50 ppm
  3. 100 ppm
  4. 10 ppm
Answer and explanation

Answer: B

P = 5.0 × 0.02 × 50 × 1000 ÷ 100 = 50 ppm.

P = 90 ppm and M = 120 ppm. The hydroxide alkalinity is:

  1. 30 ppm
  2. 90 ppm
  3. 60 ppm
  4. 120 ppm
Answer and explanation

Answer: C

P > M/2, so OH− = 2P − M = 180 − 120 = 60 ppm.

P = 40 ppm and M = 200 ppm. The hydrogencarbonate alkalinity is:

  1. 160 ppm
  2. 120 ppm
  3. 80 ppm
  4. 40 ppm
Answer and explanation

Answer: B

P < M/2, so HCO3− = M − 2P = 200 − 80 = 120 ppm (and CO3 2− = 80 ppm).

A sample gives P = 0 and M = 160 ppm. The alkalinity is due to:

  1. Hydroxide only
  2. Carbonate only
  3. Hydrogencarbonate only
  4. Hydroxide and carbonate
Answer and explanation

Answer: C

With P = 0 there is no hydroxide or carbonate, so the whole alkalinity is hydrogencarbonate.

74 g of pure lime removes temporary calcium hardness equal to 100 g of CaCO3. In 500 L of water this corresponds to a hardness of:

  1. 50 ppm
  2. 100 ppm
  3. 400 ppm
  4. 200 ppm
Answer and explanation

Answer: D

100 g = 100,000 mg; 100,000 mg ÷ 500 L = 200 mg/L = 200 ppm.

At illustrative prices of ₹8 per kg of lime and ₹40 per kg of soda, 2.0 kg of lime and 1.0 kg of soda cost:

  1. ₹48
  2. ₹56
  3. ₹66
  4. ₹80
Answer and explanation

Answer: B

Lime 2.0 × 8 = ₹16; soda 1.0 × 40 = ₹40; total ₹56.

A calculation gives 2.072 kg of pure lime. The lime available is 80% pure. The mass to be used is:

  1. 1.66 kg
  2. 2.59 kg
  3. 2.07 kg
  4. 3.20 kg
Answer and explanation

Answer: B

Mass = 2.072 ÷ 0.80 = 2.59 kg.

Water has permanent Ca 30 ppm and permanent Mg 20 ppm. The pure soda needed per litre is:

  1. 53 mg
  2. 74 mg
  3. 37 mg
  4. 106 mg
Answer and explanation

Answer: A

Soda = 1.06 × (30 + 20) = 53 mg per litre.

Water has temporary Ca 40 ppm and temporary Mg 20 ppm and no other hardness. The pure lime needed per litre is:

  1. 29.6 mg
  2. 44.4 mg
  3. 59.2 mg
  4. 74.0 mg
Answer and explanation

Answer: C

Lime = 0.74 × (40 + 2 × 20) = 0.74 × 80 = 59.2 mg per litre.

10,000 L of 60 ppm water is made by blending fully softened water with raw water of 300 ppm. The volume of softened water needed is:

  1. 2000 L
  2. 5000 L
  3. 8000 L
  4. 6000 L
Answer and explanation

Answer: C

Raw fraction = 60 ÷ 300 = 0.2, so raw = 2000 L and softened = 8000 L.

A sample has total hardness 300 ppm and alkalinity 200 ppm (all HCO3−). Its non-carbonate hardness is:

  1. 500 ppm
  2. 100 ppm
  3. 200 ppm
  4. 300 ppm
Answer and explanation

Answer: B

Alkalinity is less than total hardness, so carbonate hardness = 200 ppm and non-carbonate hardness = 300 − 200 = 100 ppm.

A sample has cations 8.0 meq/L. Its anions are HCO3− 4.0, Cl− 3.0 and SO4 2− 1.0 meq/L. The ion balance:

  1. Is exact, since the anions also total 8.0 meq/L
  2. Fails by 1 meq/L because of the sulphate
  3. Fails because sulphate is divalent
  4. Cannot be checked using meq/L values
Answer and explanation

Answer: A

4.0 + 3.0 + 1.0 = 8.0 meq/L, equal to the cations, so the balance is exact.

Raw water has alkalinity 10 mg/L (as CaCO3) and the alum dose consumes 13.5 mg/L. The lime, Ca(OH)2, needed to supply the deficiency is about:

  1. 3.5 mg/L
  2. 5.0 mg/L
  3. 1.3 mg/L
  4. 2.6 mg/L
Answer and explanation

Answer: D

Deficiency = 3.5 mg/L as CaCO3; lime = 3.5 × 74 ÷ 100 = 2.6 mg/L.

A dose of 30 mg/L of Al2(SO4)3·18H2O (666 g/mol) consumes alkalinity (as CaCO3) of:

  1. 13.5 mg/L
  2. 27 mg/L
  3. 30 mg/L
  4. 6.7 mg/L
Answer and explanation

Answer: A

30 × 300 ÷ 666 = 13.5 mg/L.

Per mg of anhydrous Al2(SO4)3 (342 g/mol), the alkalinity consumed as CaCO3 is about (3 mol CaCO3 = 300 g per mole of alum):

  1. 0.45 mg
  2. 1.14 mg
  3. 0.50 mg
  4. 0.88 mg
Answer and explanation

Answer: D

300 ÷ 342 = 0.877 mg. The hydrated form gives 0.45 mg per mg, so check which form the question names.

A dose of 3.0 mg/L leaves a free residual of 0.8 mg/L. The chlorine demand of the water is:

  1. 3.8 mg/L
  2. 2.2 mg/L
  3. 0.8 mg/L
  4. 3.0 mg/L
Answer and explanation

Answer: B

Demand = dose − residual = 3.0 − 0.8 = 2.2 mg/L.

A hypochlorite solution holds 5% w/v available chlorine. What volume gives 2 kg of chlorine?

  1. 400 L
  2. 10 L
  3. 40 L
  4. 4 L
Answer and explanation

Answer: C

5% w/v is 50 g per litre; 2000 g ÷ 50 g/L = 40 L.

What mass of bleaching powder with 25% available chlorine gives a dose of 2 mg/L to 1,000,000 L?

  1. 0.5 kg
  2. 2 kg
  3. 4 kg
  4. 8 kg
Answer and explanation

Answer: D

Chlorine = 2 kg; powder = 2 ÷ 0.25 = 8 kg.

A 25 mL aliquot containing 0.2 g of bleaching powder needs 12.0 mL of 0.1 N thiosulphate. The available chlorine is:

  1. 21.3%
  2. 42.6%
  3. 17.0%
  4. 10.7%
Answer and explanation

Answer: A

Equivalents = 1.2 meq; chlorine = 1.2 × 35.5 = 42.6 mg; 42.6 ÷ 200 × 100 = 21.3%.

The theoretical available chlorine in pure CaOCl2 (formula mass 127; Cl2 = 71) is:

  1. 27.9%
  2. 35.5%
  3. 55.9%
  4. 71.0%
Answer and explanation

Answer: C

127 g of CaOCl2 gives 71 g of Cl2, so 71 ÷ 127 × 100 = 55.9%.

The theoretical oxygen demand of 100 mg/L of ethanol (C2H5OH, 46 g/mol) is about:

  1. 48 mg/L
  2. 96 mg/L
  3. 417 mg/L
  4. 209 mg/L
Answer and explanation

Answer: D

C2H5OH + 3O2 → 2CO2 + 3H2O; 96 g of O2 per 46 g of ethanol = 2.087, so 100 mg/L needs 208.7 mg/L.

The time taken to exert half of the ultimate BOD for k = 0.23 per day is about:

  1. 0.69 days
  2. 5.0 days
  3. 3.0 days
  4. 1.15 days
Answer and explanation

Answer: C

t = ln 2 ÷ k = 0.693 ÷ 0.23 = 3.0 days.

The theoretical oxygen demand of 50 mg/L of glucose (C6H12O6 + 6O2 → 6CO2 + 6H2O) is about:

  1. 26.7 mg/L
  2. 53.3 mg/L
  3. 160 mg/L
  4. 192 mg/L
Answer and explanation

Answer: B

192 g of O2 per 180 g of glucose gives 1.067; 50 × 1.067 = 53.3 mg/L.

A waste has ultimate BOD L0 = 200 mg/L and k = 0.23 per day. Its BOD5 is about (e^(−1.15) = 0.3166):

  1. 200 mg/L
  2. 137 mg/L
  3. 63 mg/L
  4. 100 mg/L
Answer and explanation

Answer: B

BOD5 = 200 × (1 − 0.3166) = 136.7 mg/L.

250 mL of a sample needs 7.5 mL of 0.025 N thiosulphate in a Winkler titration. The DO is:

  1. 3.0 mg/L
  2. 12.0 mg/L
  3. 7.5 mg/L
  4. 6.0 mg/L
Answer and explanation

Answer: D

DO = 7.5 × 0.025 × 8 × 1000 ÷ 250 = 1500 ÷ 250 = 6.0 mg/L.

In hypothetical salt pairing, which salt represents temporary hardness?

  1. MgSO4, a magnesium sulphate
  2. CaCl2, a calcium chloride
  3. NaHCO3, a sodium hydrogencarbonate
  4. Mg(HCO3)2, a magnesium salt
Answer and explanation

Answer: D

Calcium and magnesium hydrogencarbonates give temporary hardness. NaHCO3 gives alkalinity, not hardness.

Using the pairing order, 4.0 meq/L of Ca2+ and 4.0 meq/L of HCO3− give Ca(HCO3)2 equal to what mass per litre (formula mass 162)?

  1. 648 mg
  2. 162 mg
  3. 324 mg
  4. 81 mg
Answer and explanation

Answer: C

4.0 meq ÷ 2 = 2.0 mmol; 2.0 × 162 = 324 mg/L.

A dose of 30 mg/L of Al2(SO4)3·18H2O releases carbon dioxide of about:

  1. 11.9 mg/L
  2. 30 mg/L
  3. 3.5 mg/L
  4. 26.4 mg/L
Answer and explanation

Answer: A

6 mol CO2 (264 g) per 666 g of alum: 30 × 264 ÷ 666 = 11.9 mg/L.

A 5000 L tank has dissolved oxygen of 6 mg/L. The mass of dissolved oxygen is:

  1. 3 g
  2. 30 g
  3. 300 g
  4. 30 mg
Answer and explanation

Answer: B

6 mg/L × 5000 L = 30,000 mg = 30 g.

After alum treatment of a water containing Ca(HCO3)2, the calcium appears as:

  1. Solid CaCO3 trapped inside the floc
  2. Dissolved Ca(OH)2 raising the pH
  3. Dissolved CaSO4 (non-carbonate hardness)
  4. Gaseous calcium escaping with the CO2
Answer and explanation

Answer: C

The equation gives 3CaSO4 per mole of alum. Calcium stays dissolved, so total hardness is unchanged and the carbonate hardness becomes non-carbonate.

0.01% by mass of a substance in water is equivalent to:

  1. 100 ppm
  2. 1 ppm
  3. 10 ppm
  4. 1000 ppm
Answer and explanation

Answer: A

1% = 10,000 ppm, so 0.01% = 100 ppm.

The pH of a 0.001 M solution of hydrochloric acid (fully ionised) is:

  1. 1
  2. 7
  3. 11
  4. 3
Answer and explanation

Answer: D

[H+] = 10^−3, so pH = 3.

A tank measures 2 m by 1.5 m by 1 m. When full, it holds:

  1. 300 L
  2. 30 L
  3. 3000 L
  4. 30,000 L
Answer and explanation

Answer: C

Volume = 3 m³ = 3 × 1000 = 3000 L.

0.5 g of salt dissolved in 2 L of water gives a concentration of:

  1. 25 mg/L
  2. 2.5 mg/L
  3. 1000 mg/L
  4. 250 mg/L
Answer and explanation

Answer: D

0.5 g = 500 mg; 500 mg ÷ 2 L = 250 mg/L = 250 ppm.

Privacy · Terms · Refunds · Delivery