Chemistry practice for Punjab State Civil Services Combined Competitive Examination

50 practice questions on what the checked Punjab State Civil Services Combined Competitive Examination syllabus lists under Chemistry. Each has its answer and explanation. If an answer looks wrong, please tell us.

3 kg of a fuel on complete combustion releases 1,35,000 kJ. Its calorific value is:

  1. 45,000 kJ/kg
  2. 4,05,000 kJ/kg
  3. 15,000 kJ/kg
  4. 40,500 kJ/kg
Answer and explanation

Answer: A

Calorific value = 1,35,000 ÷ 3 = 45,000 kJ/kg. Multiplying instead of dividing gives the wrong answer 4,05,000 kJ/kg.

Which balanced equation shows the incomplete combustion of methane forming carbon monoxide?

  1. 2CH4 + 3O2 → 2CO + 4H2O
  2. CH4 + 2O2 → CO2 + 2H2O
  3. CH4 + O2 → CO + H2O
  4. 2CH4 + O2 → 2CO + 2H2O
Answer and explanation

Answer: A

Check atoms: left 2 C, 8 H, 6 O; right 2 C, 8 H, 2 + 4 = 6 O. Balanced. CH4 + 2O2 → CO2 + 2H2O is complete combustion; CH4 + O2 → CO + H2O and 2CH4 + O2 → 2CO + 2H2O do not balance.

Nylon-2–nylon-6 is formed from

  1. glycine and aminocaproic acid
  2. 3-hydroxybutanoic acid and 3-hydroxypentanoic acid
  3. adipic acid and hexamethylenediamine
  4. caprolactam alone
Answer and explanation

Answer: A

Nylon-2–nylon-6 is a biodegradable polyamide of glycine and aminocaproic acid. 3-hydroxybutanoic and 3-hydroxypentanoic acids give PHBV, adipic acid and hexamethylenediamine give nylon-6,6, and caprolactam alone gives nylon-6.

Which set contains only amphoteric oxides?

  1. Al2O3, ZnO, BeO
  2. Na2O, MgO, BaO
  3. SO3, P4O10, Cl2O7
  4. CO, NO, N2O
Answer and explanation

Answer: A

Al2O3, ZnO and BeO react with both acids and bases. Na2O, MgO and BaO are basic, SO3, P4O10 and Cl2O7 acidic, and CO, NO and N2O neutral.

Which reaction temporarily ends a chlorine chain in the stratosphere?

  1. Cl + O₃ → ClO + O₂
  2. Cl + CH₄ → HCl + CH₃
  3. ClO + O → Cl + O₂
  4. CF₂Cl₂ → CF₂Cl + Cl
Answer and explanation

Answer: B

Forming HCl locks chlorine into a reservoir. Cl + O₃ → ClO + O₂ and ClO + O → Cl + O₂ are chain steps; CF₂Cl₂ → CF₂Cl + Cl starts a chain.

Which of these is a disproportionation reaction?

  1. 2H2O2 → 2H2O + O2
  2. NaOH + HCl → NaCl + H2O
  3. CaCO3 → CaO + CO2
  4. Zn + 2HCl → ZnCl2 + H2
Answer and explanation

Answer: A

In H2O2 oxygen is −1; it becomes −2 in H2O and 0 in O2, so the same element is both reduced and oxidised. NaOH + HCl and the decomposition of CaCO3 involve no change in oxidation number; Zn + 2HCl is redox between two different elements.

Mixing solutions of which pair gives a precipitate?

  1. NaCl and KNO3
  2. NaNO3 and KCl
  3. HCl and NaOH
  4. AgNO3 and KCl
Answer and explanation

Answer: D

AgNO3 + KCl → AgCl + KNO3; silver chloride is insoluble. With NaCl and KNO3, or NaNO3 and KCl, all possible products are soluble, and HCl with NaOH only forms water and soluble NaCl.

What is the anode reaction of the lead storage battery on discharge?

  1. PbO2 + 4H+ + SO4 2- + 2e- gives PbSO4 + 2H2O
  2. 2H2O gives O2 + 4H+ + 4e-
  3. Pb2+ + 2e- gives Pb
  4. Pb + SO4 2- gives PbSO4 + 2e-
Answer and explanation

Answer: D

Lead is oxidised at the anode to PbSO4. PbO2 + 4H+ + SO4 2- + 2e- gives PbSO4 + 2H2O is the cathode reaction.

At illustrative prices of ₹8 per kg of lime and ₹40 per kg of soda, 2.0 kg of lime and 1.0 kg of soda cost:

  1. ₹48
  2. ₹56
  3. ₹66
  4. ₹80
Answer and explanation

Answer: B

Lime 2.0 × 8 = ₹16; soda 1.0 × 40 = ₹40; total ₹56.

Water has temporary Ca 40 ppm and temporary Mg 20 ppm and no other hardness. The pure lime needed per litre is:

  1. 29.6 mg
  2. 44.4 mg
  3. 59.2 mg
  4. 74.0 mg
Answer and explanation

Answer: C

Lime = 0.74 × (40 + 2 × 20) = 0.74 × 80 = 59.2 mg per litre.

P = 40 ppm and M = 200 ppm. The hydrogencarbonate alkalinity is:

  1. 160 ppm
  2. 120 ppm
  3. 80 ppm
  4. 40 ppm
Answer and explanation

Answer: B

P < M/2, so HCO3− = M − 2P = 200 − 80 = 120 ppm (and CO3 2− = 80 ppm).

An effluent has COD 160 mg/L and BOD 120 mg/L. The BOD/COD ratio is:

  1. 0.75
  2. 1.33
  3. 0.25
  4. 0.50
Answer and explanation

Answer: A

120 ÷ 160 = 0.75, which means that most of the organic matter is biodegradable. The ratio cannot exceed 1.

P = 90 ppm and M = 120 ppm. The hydroxide alkalinity is:

  1. 30 ppm
  2. 90 ppm
  3. 60 ppm
  4. 120 ppm
Answer and explanation

Answer: C

P > M/2, so OH− = 2P − M = 180 − 120 = 60 ppm.

A calculation gives 2.072 kg of pure lime. The lime available is 80% pure. The mass to be used is:

  1. 1.66 kg
  2. 2.59 kg
  3. 2.07 kg
  4. 3.20 kg
Answer and explanation

Answer: B

Mass = 2.072 ÷ 0.80 = 2.59 kg.

A softener treats 3000 L/h of 200 ppm water for 10 hours. The hardness removed (as CaCO3) is:

  1. 600 g
  2. 60 kg
  3. 6.0 kg
  4. 600 kg
Answer and explanation

Answer: C

Volume = 30,000 L; hardness = 200 mg/L × 30,000 L = 6,000,000 mg = 6.0 kg.

Equal volumes of water with 81 mg/L Ca(HCO3)2 and water with 111 mg/L CaCl2 are mixed. The permanent hardness of the mixture is:

  1. 100 ppm
  2. 25 ppm
  3. 75 ppm
  4. 50 ppm
Answer and explanation

Answer: D

CaCl2 gives 100 ppm as CaCO3; after mixing equal volumes it is halved to 50 ppm.

A 100 mL sample needs 5.0 mL of 0.02 N HCl to the phenolphthalein end point. P in ppm of CaCO3 is:

  1. 25 ppm
  2. 50 ppm
  3. 100 ppm
  4. 10 ppm
Answer and explanation

Answer: B

P = 5.0 × 0.02 × 50 × 1000 ÷ 100 = 50 ppm.

5000 L of the water (200 ppm total hardness) is softened by sodium zeolite. The salt needed to regenerate the bed is:

  1. 1.00 kg
  2. 1.17 kg
  3. 2.34 kg
  4. 0.585 kg
Answer and explanation

Answer: B

Hardness removed = 200 × 5000 = 1,000,000 mg = 1.0 kg as CaCO3; NaCl = 1.0 × 117 ÷ 100 = 1.17 kg.

74 g of pure lime removes temporary calcium hardness equal to 100 g of CaCO3. In 500 L of water this corresponds to a hardness of:

  1. 50 ppm
  2. 100 ppm
  3. 400 ppm
  4. 200 ppm
Answer and explanation

Answer: D

100 g = 100,000 mg; 100,000 mg ÷ 500 L = 200 mg/L = 200 ppm.

For the same water, the pure soda needed per litre is:

  1. 53 mg
  2. 159 mg
  3. 106 mg
  4. 212 mg
Answer and explanation

Answer: C

Soda = 1.06 × (50 + 50) = 106 mg per litre.

10,000 L of 60 ppm water is made by blending fully softened water with raw water of 300 ppm. The volume of softened water needed is:

  1. 2000 L
  2. 5000 L
  3. 8000 L
  4. 6000 L
Answer and explanation

Answer: C

Raw fraction = 60 ÷ 300 = 0.2, so raw = 2000 L and softened = 8000 L.

Water has permanent Ca 30 ppm and permanent Mg 20 ppm. The pure soda needed per litre is:

  1. 53 mg
  2. 74 mg
  3. 37 mg
  4. 106 mg
Answer and explanation

Answer: A

Soda = 1.06 × (30 + 20) = 53 mg per litre.

A sample gives P = 0 and M = 160 ppm. The alkalinity is due to:

  1. Hydroxide only
  2. Carbonate only
  3. Hydrogencarbonate only
  4. Hydroxide and carbonate
Answer and explanation

Answer: C

With P = 0 there is no hydroxide or carbonate, so the whole alkalinity is hydrogencarbonate.

The volume of 0.01 M EDTA needed by 50 mL of the same water (200 ppm) is:

  1. 5 mL
  2. 20 mL
  3. 2 mL
  4. 10 mL
Answer and explanation

Answer: D

Hardness in 50 mL = 10 mg CaCO3 = 0.10 mmol; EDTA volume = 0.10 ÷ 0.01 = 10 mL.

For the water analysed above (temporary Ca 50, temporary Mg 50, permanent Ca 50, permanent Mg 50 ppm), the pure lime needed per litre is:

  1. 148 mg
  2. 74 mg
  3. 111 mg
  4. 200 mg
Answer and explanation

Answer: A

Lime = 0.74 × (50 + 2 × 50 + 50) = 0.74 × 200 = 148 mg per litre.

A water has total hardness 120 ppm and alkalinity 200 ppm (all HCO3−). Its non-carbonate hardness is:

  1. 0 ppm
  2. 80 ppm
  3. 120 ppm
  4. 200 ppm
Answer and explanation

Answer: A

Alkalinity exceeds hardness, so all of the hardness is carbonate hardness and the non-carbonate hardness is zero.

Water of 200 ppm is mixed with water of 50 ppm to give 125 ppm. The volumes needed are in the ratio (hard : soft):

  1. 1 : 1
  2. 1 : 2
  3. 2 : 1
  4. 1 : 3
Answer and explanation

Answer: A

200x + 50(1 − x) = 125 gives x = 0.5, so the volumes are equal.

Which method forces water through a semipermeable membrane using high pressure to remove salts?

  1. Reverse osmosis
  2. Distillation
  3. Filtration through sand
  4. Coagulation with alum
Answer and explanation

Answer: A

Reverse osmosis applies pressure above the osmotic pressure, driving water through the membrane.

A roof of area 50 m² receives 100 mm of rain. If 80% is captured, the volume collected is:

  1. 5000 L
  2. 500 L
  3. 4000 L
  4. 40,000 L
Answer and explanation

Answer: C

Total volume = 50 × 0.1 = 5 m³ = 5000 L; 80% of that is 4000 L.

Heat to evaporate 10 kg of water already at 100 °C (L = 22.6 × 10⁵ J/kg) is:

  1. 2.26 × 10⁶ J
  2. 2.26 × 10⁷ J
  3. 2.26 × 10⁵ J
  4. 4.2 × 10⁴ J
Answer and explanation

Answer: B

Q = 10 × 22.6 × 10⁵ = 2.26 × 10⁷ J.

Distilled water is almost pure because:

  1. Germs are all killed by filtration
  2. Chlorine is added during boiling
  3. Dissolved salts stay behind as water evaporates
  4. Alum is mixed in and removes the salts
Answer and explanation

Answer: C

When water boils, the dissolved salts do not form vapour, so the condensed steam is almost free of them.

400 L of water of 300 ppm is mixed with 600 L of water of 100 ppm. The hardness of the mixture is:

  1. 200 ppm
  2. 180 ppm
  3. 220 ppm
  4. 150 ppm
Answer and explanation

Answer: B

Mass = 400 × 300 + 600 × 100 = 180,000 mg in 1000 L, so 180 ppm.

0.01% by mass of a substance in water is equivalent to:

  1. 100 ppm
  2. 1 ppm
  3. 10 ppm
  4. 1000 ppm
Answer and explanation

Answer: A

1% = 10,000 ppm, so 0.01% = 100 ppm.

A 5000 L tank has dissolved oxygen of 6 mg/L. The mass of dissolved oxygen is:

  1. 3 g
  2. 30 g
  3. 300 g
  4. 30 mg
Answer and explanation

Answer: B

6 mg/L × 5000 L = 30,000 mg = 30 g.

A 40 L sample contains 20 mg of a pollutant. Its concentration is:

  1. 20 mg/L
  2. 800 mg/L
  3. 0.5 mg/L
  4. 2 mg/L
Answer and explanation

Answer: C

20 mg ÷ 40 L = 0.5 mg/L = 0.5 ppm.

0.5 g of salt dissolved in 2 L of water gives a concentration of:

  1. 25 mg/L
  2. 2.5 mg/L
  3. 1000 mg/L
  4. 250 mg/L
Answer and explanation

Answer: D

0.5 g = 500 mg; 500 mg ÷ 2 L = 250 mg/L = 250 ppm.

A water sample has pH 9 at 25 °C. Its hydroxide ion concentration is:

  1. 10^−9 mol/L
  2. 10^−5 mol/L
  3. 10^−7 mol/L
  4. 10^−14 mol/L
Answer and explanation

Answer: B

pOH = 14 − 9 = 5, so [OH−] = 10^−5 mol/L.

A drop of phenolphthalein is added to lime water (a base). The colour becomes:

  1. Colourless
  2. Pink
  3. Red
  4. Yellow
Answer and explanation

Answer: B

Phenolphthalein is colourless in acid and pink in base.

500 mL of water leaves a residue of 0.15 g on evaporation. The TDS is:

  1. 30 mg/L
  2. 75 mg/L
  3. 300 mg/L
  4. 3000 mg/L
Answer and explanation

Answer: C

Residue = 150 mg; volume = 0.5 L; TDS = 150 ÷ 0.5 = 300 mg/L.

In sewage treatment, microbes break down organic matter and lower the BOD in which stage?

  1. Primary treatment
  2. Secondary treatment
  3. Screening
  4. Skimming of oil
Answer and explanation

Answer: B

Secondary (biological) treatment uses air and microbes to oxidise organic matter, lowering the BOD.

A household of 5 persons uses 100 L per person per day (illustrative). The use over 30 days is:

  1. 5,000 L
  2. 1,500 L
  3. 150,000 L
  4. 15,000 L
Answer and explanation

Answer: D

5 × 100 × 30 = 15,000 L, which is 15 m³.

In the water cycle, the change of water vapour into droplets that form clouds is called:

  1. Evaporation
  2. Condensation
  3. Precipitation
  4. Transpiration
Answer and explanation

Answer: B

Vapour cooling into liquid droplets is condensation.

Well water is often hard because it:

  1. Dissolves calcium and magnesium salts from rocks
  2. Collects dust while falling through the air
  3. Carries sodium chloride in from the sea
  4. Has been distilled underground first
Answer and explanation

Answer: A

Groundwater is in long contact with rock, from which it dissolves calcium and magnesium salts.

A dose of 30 mg/L of Al2(SO4)3·18H2O (666 g/mol) consumes alkalinity (as CaCO3) of:

  1. 13.5 mg/L
  2. 27 mg/L
  3. 30 mg/L
  4. 6.7 mg/L
Answer and explanation

Answer: A

30 × 300 ÷ 666 = 13.5 mg/L.

Raw water has alkalinity 10 mg/L (as CaCO3) and the alum dose consumes 13.5 mg/L. The lime, Ca(OH)2, needed to supply the deficiency is about:

  1. 3.5 mg/L
  2. 5.0 mg/L
  3. 1.3 mg/L
  4. 2.6 mg/L
Answer and explanation

Answer: D

Deficiency = 3.5 mg/L as CaCO3; lime = 3.5 × 74 ÷ 100 = 2.6 mg/L.

After alum treatment of a water containing Ca(HCO3)2, the calcium appears as:

  1. Solid CaCO3 trapped inside the floc
  2. Dissolved Ca(OH)2 raising the pH
  3. Dissolved CaSO4 (non-carbonate hardness)
  4. Gaseous calcium escaping with the CO2
Answer and explanation

Answer: C

The equation gives 3CaSO4 per mole of alum. Calcium stays dissolved, so total hardness is unchanged and the carbonate hardness becomes non-carbonate.

A tank measures 2 m by 1.5 m by 1 m. When full, it holds:

  1. 300 L
  2. 30 L
  3. 3000 L
  4. 30,000 L
Answer and explanation

Answer: C

Volume = 3 m³ = 3 × 1000 = 3000 L.

A dose of 30 mg/L of Al2(SO4)3·18H2O releases carbon dioxide of about:

  1. 11.9 mg/L
  2. 30 mg/L
  3. 3.5 mg/L
  4. 26.4 mg/L
Answer and explanation

Answer: A

6 mol CO2 (264 g) per 666 g of alum: 30 × 264 ÷ 666 = 11.9 mg/L.

Rain water is slightly acidic because it:

  1. Collects chlorine from the pipes it runs through
  2. Dissolves carbon dioxide from air, forming carbonic acid
  3. Carries sea salt up from the ocean surface
  4. Is full of dissolved calcium from the clouds
Answer and explanation

Answer: B

Dissolved CO2 forms a very weak acid, carbonic acid, so even clean rain has a pH a little below 7.

Compared with a solution of pH 5, a solution of pH 3 has a hydrogen-ion concentration that is:

  1. 2 times greater
  2. 20 times greater
  3. 100 times greater
  4. 1000 times greater
Answer and explanation

Answer: C

A difference of 2 pH units is a factor of 10^2 = 100.

Privacy · Terms · Refunds · Delivery