Chapter 11 Electricity
Practice questions
Why is tungsten used for the filament of an incandescent bulb?
- It has a very high melting point
- It has zero resistance
- It does not get hot
- It is a good insulator
Answer and explanation
Answer: A
The filament must become hot enough to glow without melting. Tungsten's very high melting point allows this; the bulb is also filled with inactive gas to make the filament last longer.
A 2 kW geyser runs on a 220 V supply. Which fuse rating is the most suitable for its circuit?
- 1 A
- 5 A
- 10 A
- 100 A
Answer and explanation
Answer: C
I = P ÷ V = 2000 ÷ 220 ≈ 9.1 A. The fuse must be a little above the normal current, so 10 A suits; 1 A or 5 A would blow at once, and 100 A would give no protection.
Five 40 W bulbs are used for 6 hours a day for 30 days. At an illustrative rate of ₹5 per unit, the cost is
- ₹36
- ₹1,800
- ₹900
- ₹180
Answer and explanation
Answer: D
Energy = 5 × 40 W × 6 h × 30 = 36,000 W h = 36 kW h. Cost = 36 × ₹5 = ₹180.
A bulb is rated 100 W, 220 V. Its resistance when working normally is
- 2.2 Ω
- 484 Ω
- 22,000 Ω
- 0.45 Ω
Answer and explanation
Answer: B
R = V² ÷ P = 220² ÷ 100 = 48400 ÷ 100 = 484 Ω.
A current of 0.5 A flows through a 40 Ω resistor for 5 minutes. The heat produced is
- 3000 J
- 100 J
- 6000 J
- 50 J
Answer and explanation
Answer: A
t = 5 × 60 = 300 s. H = I²Rt = 0.5² × 40 × 300 = 0.25 × 40 × 300 = 3000 J.
A string of decorative bulbs is connected in series. One bulb's filament breaks. What happens?
- Only that bulb goes off
- The other bulbs glow more brightly
- All the bulbs go off
- The fuse in the house melts
Answer and explanation
Answer: C
In series there is only one path. A broken filament opens the circuit, so current stops in every bulb.
Resistors of 2 Ω and 4 Ω are connected in parallel across a 6 V battery. The total current drawn from the battery is
- 1 A
- 4.5 A
- 3 A
- 1.5 A
Answer and explanation
Answer: B
Each gets 6 V. I₁ = 6 ÷ 2 = 3 A and I₂ = 6 ÷ 4 = 1.5 A. Total I = 3 + 1.5 = 4.5 A. (Check: Rp = 8/6 = 4/3 Ω, and 6 ÷ 4/3 = 4.5 A.)
You have three 6 Ω resistors. How can you join all three to get 9 Ω?
- All three in series
- All three in parallel
- Two in series, and that pair in parallel with the third
- Two in parallel, and that pair in series with the third
Answer and explanation
Answer: D
Two 6 Ω in parallel give 3 Ω; adding the third in series gives 3 + 6 = 9 Ω. (All in series = 18 Ω; all in parallel = 2 Ω; 12 Ω in parallel with 6 Ω = 4 Ω.)
A metal wire of resistivity 1.7 × 10⁻⁸ Ω m is 100 m long with a cross-sectional area of 1 mm². Its resistance is
- 1.7 Ω
- 0.17 Ω
- 17 Ω
- 1.7 × 10⁻⁶ Ω
Answer and explanation
Answer: A
A = 1 mm² = 1 × 10⁻⁶ m². R = ρl ÷ A = (1.7 × 10⁻⁸ × 100) ÷ 10⁻⁶ = 1.7 × 10⁻⁶ ÷ 10⁻⁶ = 1.7 Ω.
A uniform wire is stretched to three times its original length without changing its volume. Its resistance becomes
- 3 times
- 1/3 of the original
- 9 times
- 6 times
Answer and explanation
Answer: C
Length becomes 3l and area becomes A/3 (volume unchanged). R′ = ρ(3l) ÷ (A/3) = 9ρl/A = 9R.
A wire of resistance R is cut into four equal pieces, and the four pieces are joined in parallel. The equivalent resistance is
- R/16
- R/4
- 4R
- R
Answer and explanation
Answer: A
Each piece has resistance R/4. Four equal resistances of R/4 in parallel give (R/4) ÷ 4 = R/16.
A wire carries 0.25 A when the potential difference across it is 2.0 V. At the same temperature, what current flows when the potential difference is 5.0 V?
- 0.10 A
- 1.25 A
- 0.4 A
- 0.625 A
Answer and explanation
Answer: D
R = V ÷ I = 2.0 ÷ 0.25 = 8 Ω. At 5.0 V, I = 5.0 ÷ 8 = 0.625 A.
Assertion (A): An ammeter is connected in series with a component.
Reason (R): The current is the same at every point of a series path, so the ammeter reads the current through the component.
- Both A and R are true, and R is the correct explanation of A
- Both A and R are true, but R is not the correct explanation of A
- A is true, but R is false
- A is false, but R is true
Answer and explanation
Answer: A
Both are true. Placing the ammeter in the same single path makes the component's whole current pass through it, so R correctly explains A.
How much work is done in moving 50 C of charge across a potential difference of 220 V?
- 4.4 J
- 270 J
- 11,000 J
- 1,100 J
Answer and explanation
Answer: C
W = V × Q = 220 × 50 = 11,000 J (11 kJ).
A current of 1.6 A flows in a wire for 10 s. How many electrons pass a point in the wire? (charge on an electron = 1.6 × 10⁻¹⁹ C)
- 10¹⁹
- 10²⁰
- 1.6 × 10²⁰
- 2.56 × 10⁻¹⁸
Answer and explanation
Answer: B
Q = I × t = 1.6 × 10 = 16 C. n = Q ÷ e = 16 ÷ (1.6 × 10⁻¹⁹) = 10 × 10¹⁹ = 10²⁰ electrons.
Assertion (A): A fuse is connected in series with the appliance it protects.
Reason (R): When a fuse melts, it breaks the only path for current to that appliance.
- Both A and R are true, and R is the correct explanation of A
- Both A and R are true, but R is not the correct explanation of A
- A is true, but R is false
- A is false, but R is true
Answer and explanation
Answer: A
Both are true. Because the fuse is in series, all the current passes through it, and when it melts the circuit is broken; R correctly explains A.
An electric kettle of 1500 W is used for 20 minutes every day for 30 days. The energy used is
- 15 kW h
- 45 kW h
- 900 kW h
- 150 kW h
Answer and explanation
Answer: A
Power = 1.5 kW; time per day = 20 min = 1/3 h. Energy = 1.5 × (1/3) × 30 = 0.5 × 30 = 15 kW h.
One kilowatt hour is equal to
- 1000 J
- 3600 J
- 3.6 × 10⁵ J
- 3.6 × 10⁶ J
Answer and explanation
Answer: D
1 kW h = 1000 W × 3600 s = 3,600,000 J = 3.6 × 10⁶ J.
An appliance draws 5 A from a 220 V supply. Its power is
- 44 W
- 225 W
- 1100 W
- 2200 W
Answer and explanation
Answer: C
P = V × I = 220 × 5 = 1100 W, i.e. 1.1 kW.
If the current through a heater coil is doubled, the heat produced in the same time becomes
- four times
- double
- half
- the same
Answer and explanation
Answer: A
H = I²Rt. Doubling I multiplies I² by 2² = 4, so the heat becomes four times.