Tamil Nadu Board Class 12 Geography

Practice questions

When plotting a compass traverse, why is a new north line drawn at the start of each line?

  1. Because north changes at every station
  2. To make the plot look neater
  3. Because each bearing is measured clockwise from north at that station, so the protractor must start from a north line there
  4. Because the scale changes for every line
Answer and explanation

Answer: C

Each bearing is measured from north at the station where it was observed. Drawing a parallel north line there lets the protractor measure the bearing correctly.

Made-up closed traverse: AB 0°, 30 m; BC 90°, 30 m; CD 180°, 30 m; DA 270°, 30 m. The figure and its area are:

  1. a square of area 900 m²
  2. a rectangle of area 1,200 m²
  3. a triangle of area 450 m²
  4. a square of area 120 m²
Answer and explanation

Answer: A

North 30 m, east 30 m, south 30 m and west 30 m return to the start, forming a square of side 30 m. Area = 30 × 30 = 900 m². 120 m is the perimeter, not an area.

The fore bearing of line XY is 75° and its back bearing was read as 259°. What does this show?

  1. The readings are correct
  2. There is a 4° discrepancy, so local attraction or a misreading is likely and the line should be checked
  3. The line is due east
  4. The traverse is open
Answer and explanation

Answer: B

The expected back bearing is 75° + 180° = 255°. The reading of 259° is 4° off, which points to local attraction at a station or a reading error.

The fore bearing of a line is 200°. Its back bearing is:

  1. 380°
  2. 160°
  3. 110°
  4. 20°
Answer and explanation

Answer: D

200° is more than 180°, so subtract 180°: 200° - 180° = 20°.

Which part of a prismatic compass is used when sighting an object that is much higher or lower than the observer?

  1. Sun glasses
  2. Ball and socket
  3. Adjustable mirror
  4. Brake pin
Answer and explanation

Answer: C

The hinged adjustable mirror on the sighting vane lets an observer sight objects that are too high or too low by reflection.

In a prismatic compass, which part reflects and magnifies the ring's readings to the eye?

  1. The prism
  2. The brake pin
  3. The mirror on the object vane
  4. The glass cover
Answer and explanation

Answer: A

The prism on the eye vane magnifies the graduations on the aluminium ring and reflects them to the eye while sighting. The mirror on the object vane is for sighting high or low objects.

Made-up data: the top of a tower is 24 m above your eye level and the angle of elevation is 50° (tan 50° = 1.1918). Your distance from the tower is about:

  1. 28.6 m
  2. 24.0 m
  3. 13.2 m
  4. 20.1 m
Answer and explanation

Answer: D

d = x ÷ tan θ = 24 ÷ 1.1918 = 20.14, about 20.1 m. Check: 20.14 × 1.1918 = 24.0 m. 28.6 m comes from multiplying instead of dividing.

Made-up data: clinometer reading 30°, distance 10 m, eye-height 1.5 m, tan 60° = 1.7321. The height of the building is about:

  1. 7.3 m
  2. 18.8 m
  3. 17.3 m
  4. 11.5 m
Answer and explanation

Answer: B

Angle of elevation = 90° - 30° = 60°. x = 10 × 1.7321 = 17.321 m. h = 17.321 + 1.5 = 18.821, about 18.8 m. 7.3 m comes from wrongly using tan 30°.

Made-up data: angle of elevation 35° (tan 35° = 0.7002), distance 20 m, eye-height 1.5 m. The height of the tree is about:

  1. 14.0 m
  2. 12.5 m
  3. 15.5 m
  4. 29.3 m
Answer and explanation

Answer: C

x = 20 × 0.7002 = 14.004 m. h = 14.004 + 1.5 = 15.504, about 15.5 m. 14.0 m forgets the eye-height.

Why is the eye-height added at the end of the height calculation?

  1. Because the triangle's opposite side starts at eye level, not at the ground
  2. Because the tangent table assumes it
  3. Because the clinometer reading includes it twice
  4. Because it corrects for the earth's curvature
Answer and explanation

Answer: A

The horizontal line of sight is at eye level, so d × tan θ gives only the height above the eye. The eye-height (the part below) must be added to get the full height from the ground.

Looking down from the top of a lighthouse at a boat, the angle between the horizontal and the line of sight is the:

  1. angle of elevation
  2. angle of depression
  3. back bearing
  4. magnetic declination
Answer and explanation

Answer: B

Looking down below the horizontal gives an angle of depression. Looking up gives an angle of elevation.

On a protractor clinometer the string crosses 38°. The angle of elevation is:

  1. 38°
  2. 128°
  3. 52°
  4. 62°
Answer and explanation

Answer: C

The reading is measured from the vertical, so the angle of elevation is 90° - 38° = 52°.

A side of 36 m is drawn on a plan at 1 cm to 4 m. Its length on the plan is:

  1. 9 cm
  2. 4 cm
  3. 36 cm
  4. 144 cm
Answer and explanation

Answer: A

Plan length = ground length ÷ ground value of 1 cm = 36 ÷ 4 = 9 cm.

Which quantity is NOT named in the chapter's definition of what surveying measures and records?

  1. Distances
  2. Angles
  3. Heights
  4. Temperatures
Answer and explanation

Answer: D

Surveying measures distances, angles, heights and sizes on the earth's surface. Temperature is measured by meteorologists, not in surveying.

A town planner needs the outline of a new housing plot and the height of an old water tower beside it. Which pair of instruments suits these two jobs?

  1. Clinometer for the outline, prismatic compass for the height
  2. Prismatic compass with a tape for the outline, clinometer with a tape for the height
  3. Rain gauge for both
  4. Prismatic compass alone for both
Answer and explanation

Answer: B

The outline needs bearings (horizontal angles) and lengths, so a prismatic compass and tape. The height needs a vertical angle and a distance, so a clinometer and tape.

Made-up data: on a plot at 1 cm to 10 m, a line has bearing 270° and length 50 m. How is it drawn?

  1. 5 cm due east
  2. 50 cm due west
  3. 5 cm due south
  4. 5 cm due west
Answer and explanation

Answer: D

A bearing of 270° is due west, and 50 m at 1 cm to 10 m is 50 ÷ 10 = 5 cm.

Which survey would be an open traverse?

  1. The boundary of a school ground
  2. The walls of a rectangular building
  3. The course of a winding canal from a dam to a village
  4. The fence round a temple tank
Answer and explanation

Answer: C

An open traverse starts and ends at different points, as along a canal, road or river. Boundaries of grounds, buildings and tanks return to the start and are closed traverses.

The fore bearing of a line is 300°. Its back bearing is:

  1. 480°
  2. 60°
  3. 210°
  4. 120°
Answer and explanation

Answer: D

300° is more than 180°, so subtract 180°: 300° - 180° = 120°.

The fore bearing of a line is 125°. Its back bearing is:

  1. 305°
  2. 55°
  3. 235°
  4. 145°
Answer and explanation

Answer: A

125° is less than 180°, so add 180°: 125° + 180° = 305°.

A magnetic bearing is measured from magnetic north in which direction?

  1. Anticlockwise
  2. Clockwise
  3. Towards the nearest of north or south
  4. Vertically upwards
Answer and explanation

Answer: B

The prismatic compass gives the horizontal angle of a line measured from magnetic north in the clockwise direction, from 0° to 360°.

Privacy · Terms · Refunds · Delivery