Unit 4 Electromagnetic Induction And Alternating Current

Practice questions

In an ideal LC circuit the maximum charge on the capacitor is Q_m. At the instant the energy is shared equally between the capacitor and the inductor, the charge is:

  1. Q_m/2
  2. Q_m/4
  3. Q_m/√2
  4. zero
Answer and explanation

Answer: C

Total energy = Q_m²/2C. Equal sharing means q²/2C = ½ × Q_m²/2C, so q² = Q_m²/2 and q = Q_m/√2.

An RMS current of 10 A lags the voltage by 30°. The wattless component of the current is:

  1. 8.66 A
  2. 5 A
  3. 10 A
  4. 0 A
Answer and explanation

Answer: B

Wattless current = I_RMS sin φ = 10 × sin 30° = 5 A. The wattful part is 10 cos 30° = 8.66 A.

A series circuit of impedance 80 Ω and resistance 48 Ω is connected to 240 V RMS. The average power consumed is:

  1. 720 W
  2. 576 W
  3. 240 W
  4. 432 W
Answer and explanation

Answer: D

I_RMS = 240/80 = 3 A; power factor = R/Z = 48/80 = 0.6; P = 240 × 3 × 0.6 = 432 W. Check: I²R = 9 × 48 = 432 W.

A series RLC circuit has R = 20 Ω, L = 0.2 H and C = 5 μF and is driven at its resonant frequency by a 5 V (RMS) source. The RMS voltage across the inductor is:

  1. 50 V
  2. 5 V
  3. 0.5 V
  4. 100 V
Answer and explanation

Answer: A

Q = (1/R)√(L/C) = (1/20)√(0.2/5 × 10⁻⁶) = 0.05 × √40 000 = 0.05 × 200 = 10. At resonance V_L = Q × applied voltage = 10 × 5 = 50 V.

In a series RLC circuit R = 100 Ω, X_L = 50 Ω and X_C = 150 Ω. Which statement is correct?

  1. The voltage leads the current by 45°
  2. Current and voltage are in phase
  3. The current leads the voltage by 45°
  4. The current leads the voltage by 90°
Answer and explanation

Answer: C

tan φ = (X_L − X_C)/R = (50 − 150)/100 = −1, so φ = −45°. A negative φ means a capacitive circuit: the current leads the voltage by 45°.

A current i = 4√2 sin ωt A flows through a 10 Ω resistor. The heat produced in one minute is:

  1. 160 J
  2. 19 200 J
  3. 4800 J
  4. 9600 J
Answer and explanation

Answer: D

I_RMS = I_m/√2 = 4 A. Heat = I_RMS² R t = 16 × 10 × 60 = 9600 J. Using the peak value (4√2) would double this to 19 200 J.

The same power is transmitted along the same line first at 11 kV and then at 110 kV. The ratio (loss at 11 kV)/(loss at 110 kV) is:

  1. 10
  2. 100
  3. 1/100
  4. 1
Answer and explanation

Answer: B

I = P/V, so the current at 11 kV is 10 times the current at 110 kV. Loss = I²R, so the loss is 10² = 100 times greater at 11 kV.

A step-down transformer of efficiency 90% takes 2.0 kW from the mains and supplies its load at 50 V. The current in the load is:

  1. 40 A
  2. 4 A
  3. 36 A
  4. 3.6 A
Answer and explanation

Answer: C

Output power = 0.90 × 2000 = 1800 W. I_s = P/V = 1800/50 = 36 A. Assuming 100% efficiency would give 40 A.

A generator coil has 100 turns of area 0.1 m² and rotates at 50 rad s⁻¹ in a field of 0.2 T. The peak emf is:

  1. 100 V
  2. 10 V
  3. 50 V
  4. 1000 V
Answer and explanation

Answer: A

ε_m = NBAω = 100 × 0.2 × 0.1 × 50 = 100 V.

The magnetic energy density in a region where B = 0.5 T is about (μ₀ = 4π × 10⁻⁷ T m A⁻¹):

  1. 2.0 × 10⁵ J m⁻³
  2. 9.9 × 10⁴ J m⁻³
  3. 4.0 × 10⁵ J m⁻³
  4. 9.9 × 10⁻⁸ J m⁻³
Answer and explanation

Answer: B

u = B²/2μ₀ = 0.25/(2 × 4π × 10⁻⁷) = 0.25/(2.513 × 10⁻⁶) = 9.9 × 10⁴ J m⁻³. Forgetting the 2 gives 2.0 × 10⁵.

An air-core solenoid has inductance 2.0 mH. With an iron core filling it, the inductance becomes 0.90 H. The relative permeability of the iron is:

  1. 45
  2. 4500
  3. 1.8
  4. 450
Answer and explanation

Answer: D

L = μ₀μ_r n²Al, so μ_r = L_iron/L_air = 0.90/(2.0 × 10⁻³) = 450.

A solid copper plate and an identical plate with slots cut in it swing as pendulums between the poles of a strong magnet. Compared with the solid plate, the slotted plate:

  1. stops sooner, since the slots increase the eddy currents
  2. stops at the same time
  3. keeps swinging longer, since the slots reduce the eddy currents
  4. stops at once, since slots make it non-magnetic
Answer and explanation

Answer: C

The slots break up the circulating eddy current paths, so the eddy currents and their damping force are smaller. The slotted plate swings for longer.

A metal rod 1.0 m long rotates at 10 rad s⁻¹ about one end in a plane perpendicular to a uniform field of 0.4 T. The emf between its ends is:

  1. 4 V
  2. 0.4 V
  3. 20 V
  4. 2 V
Answer and explanation

Answer: D

ε = ½Bωl² = 0.5 × 0.4 × 10 × 1.0² = 2 V. Using Blv with the tip speed (10 m s⁻¹) would give 4 V, which is wrong because the speed varies along the rod; the average speed is half the tip speed.

The north pole of a bar magnet is pulled away from one end of a coil. Seen from the magnet, the induced current makes the near end of the coil:

  1. a south pole, attracting the magnet
  2. a north pole, repelling the magnet
  3. a north pole, attracting the magnet
  4. neither pole, since the magnet is moving away
Answer and explanation

Answer: A

By Lenz's law the coil opposes the withdrawal, so it attracts the receding north pole: its near end becomes a south pole.

A coil of 100 turns and area 0.02 m² is in a uniform field of 0.5 T with its plane perpendicular to the field. It is turned in 0.1 s until its plane is parallel to the field. The average induced emf is:

  1. 1 V
  2. 10 V
  3. 0.1 V
  4. 100 V
Answer and explanation

Answer: B

Initial flux per turn = BA cos 0° = 0.5 × 0.02 = 0.01 Wb; final = BA cos 90° = 0. ε = NΔΦ/Δt = 100 × 0.01/0.1 = 10 V.

An LC circuit has L = 0.5 H and C = 2 μF. The angular frequency of its oscillations is:

  1. 100 rad s⁻¹
  2. 500 rad s⁻¹
  3. 10 000 rad s⁻¹
  4. 1000 rad s⁻¹
Answer and explanation

Answer: D

LC = 0.5 × 2 × 10⁻⁶ = 1.0 × 10⁻⁶ s², √(LC) = 1.0 × 10⁻³ s, so ω = 1/√(LC) = 1000 rad s⁻¹.

In the analogy between an LC circuit and a spring-mass system, the inductance L corresponds to:

  1. the force constant k
  2. the mass m
  3. the displacement x
  4. the velocity v
Answer and explanation

Answer: B

Magnetic energy ½Li² matches kinetic energy ½mv², with i matching v, so L matches m. It is 1/C that matches k.

The power factor of a series RLC circuit at resonance is:

  1. 1
  2. 0
  3. 0.5
  4. 0.707
Answer and explanation

Answer: A

At resonance X_L = X_C, so Z = R and φ = 0: cos φ = R/Z = 1.

A circuit draws 2 A RMS from a 100 V RMS supply with a power factor of 0.8. The true power is:

  1. 200 W
  2. 250 W
  3. 120 W
  4. 160 W
Answer and explanation

Answer: D

P_av = V_RMS I_RMS cos φ = 100 × 2 × 0.8 = 160 W. The apparent power is 200 VA.

The average power consumed over a cycle by a pure inductor connected to an AC source is:

  1. V_RMS I_RMS
  2. ½V_mI_m
  3. zero
  4. V_mI_m
Answer and explanation

Answer: C

In a pure inductor φ = 90°, so cos φ = 0 and P_av = V_RMS I_RMS × 0 = 0. The current is wholly wattless.

Privacy · Terms · Refunds · Delivery