Revision notes

Chapter 9 The Amazing World of Solutes, Solvents, and Solutions: Foundation

The key points, rules to remember, tables and diagrams from all 5 lessons, on one page for quick revision. To keep a copy, use your browser's Print and choose "Save as PDF".

Lesson 1

Solutes, solvents and solutions

Solute + solvent → solution. A solution is a uniform mixture in which the solute is evenly spread through the solvent.

Mixtures with water

  • Solutions (uniform)
    • Sugar in water
    • Salt in water
    • ORS
    • Oxygen dissolved in water
  • Non-uniform mixtures
    • Sand in water (sinks)
    • Sawdust in water (floats)
    • Chalk powder in water
Solutes and solvents
SolutionSoluteSolvent
Salt waterSaltWater
Sugar syrup (chashni)SugarWater
VinegarAcetic acid (smaller amount)Water (larger amount)
Soda waterCarbon dioxide gasWater
Water in a pondDissolved oxygenWater

Key takeaways: a solution is a uniform mixture of a solute dissolved in a solvent. In a solid-liquid solution, the liquid is the solvent even if there is more solid; in a liquid-liquid solution, the larger amount is the solvent. Sand, chalk and sawdust in water are non-uniform mixtures, not solutions. Water dissolves many substances and is widely used as a solvent.

Read the full lesson

Lesson 2

How much can dissolve? Saturation, concentration and solubility

From unsaturated to saturated

  1. Add a little solute It dissolves completely: unsaturated
  2. Keep adding and stirring Still dissolving, but the solution is getting more concentrated
  3. Limit reached Extra solute settles at the bottom: saturated at this temperature
  4. Heat it Most solids then dissolve further: it becomes unsaturated again

Effect of heating on solubility in water

  • Most solids (salt, sugar, baking soda)
    • Solubility increases
    • More dissolves in hot water
    • Saturated solution becomes unsaturated
  • Gases (oxygen, carbon dioxide)
    • Solubility decreases
    • Gas escapes from warm water
    • Less oxygen for aquatic life
Key terms
TermMeaning
Unsaturated solutionMore solute can still dissolve at that temperature
Saturated solutionNo more solute can dissolve at that temperature
ConcentrationAmount of solute in a fixed amount of solution
SolubilityMaximum amount of solute that dissolves in a fixed amount of solvent at a given temperature

Solubility is the maximum amount of solute that dissolves in a fixed amount of solvent at a given temperature; for most solids it rises with temperature, but for gases it falls.

Key takeaways: an unsaturated solution can dissolve more solute; a saturated one cannot at that temperature. Concentration compares how much solute is in a fixed amount of solution; dilute and concentrated are relative terms. Solubility is the maximum that can dissolve; for most solids it increases with temperature, while gases like oxygen dissolve less in warm water, which affects aquatic life.

Read the full lesson

Lesson 3

Density: how heavy for its size

Density = Mass ÷ Volume. SI unit: kg/m³; for small samples, g/cm³ or g/mL are used.

Compare with water's density (about 1 g/cm³)

  • Less dense than water
    • Floats
    • Wood, cooking oil, ice, rice husk
  • Denser than water
    • Sinks
    • Iron, stone, aluminium, rice grains
Density formulas
To findUse
DensityMass ÷ Volume
MassDensity × Volume
VolumeMass ÷ Density
Relative densityDensity of substance ÷ Density of water

Key takeaways: density is mass per unit volume, density = mass ÷ volume, measured in kg/m³ or g/cm³ (= g/mL). Water's density is about 1 g/cm³. Relative density compares a substance with water and has no unit. Substances less dense than water tend to float in it; denser ones sink. Rearranging the formula gives mass or volume.

Read the full lesson

Lesson 4

Measuring mass and volume to find density

Using a digital balance

  1. Switch on The display should read zero; if not, press tare (reset)
  2. Place a clean watch glass or butter paper on the pan It shows the container's mass
  3. Press tare again The display returns to zero, so the container is not counted
  4. Add the object The reading is the object's mass alone
Finding the volume of a solid
ShapeMethodExample
Regular (cuboid)Volume = length × width × heightA box 20 cm × 15 cm × 1.5 cm = 450 cm³
Irregular (stone, key)Displacement: volume = final water level − initial water levelWater rises from 60 mL to 72 mL, so volume = 12 mL = 12 cm³

Volume of an irregular solid by displacement

  1. Pour water Fill a measuring cylinder to a known level, for example 60 mL
  2. Lower the object on a thread Gently, so no water splashes out
  3. Read the new level For example 72 mL
  4. Subtract 72 mL − 60 mL = 12 mL = 12 cm³

For an irregular solid, volume = final level − initial level in a measuring cylinder; 1 mL = 1 cm³. Then density = mass ÷ volume.

Key takeaways: tare the balance so only the object's mass is shown. Find a measuring cylinder's smallest reading by dividing the value between numbered marks by the number of divisions, choose a suitable size, and read the bottom of the meniscus for clear liquids. Regular solids: volume = l × w × h; irregular solids: volume by water displacement. Then density = mass ÷ volume.

Read the full lesson

Lesson 5

How temperature and pressure change density

Why hot air rises

  1. Air is heated Its particles move faster and spread out
  2. Volume increases The same mass of air takes up more space
  3. Density decreases Mass ÷ larger volume = smaller density
  4. Hot air rises Less dense air is pushed up by the denser cool air around it
Effect of increasing pressure
StateEffect on densityReason
GasIncreases a lotParticles are far apart and are pushed much closer
LiquidIncreases very slightlyParticles are already close; nearly incompressible
SolidPractically no changeParticles are closest of all

Most substances and water on freezing

  • Most substances
    • Contract on cooling and freezing
    • Solid is denser than liquid
    • Solid sinks in its own liquid
  • Water
    • Expands on freezing
    • Ice is less dense than water
    • Ice floats

Density = mass ÷ volume: heating usually increases volume and lowers density; water is unusual because ice is less dense than liquid water.

Key takeaways: heating spreads particles out, increasing volume and lowering density, which is why hot air rises. Pressure greatly increases the density of gases, hardly affects liquids and practically not solids. Water expands on freezing, so ice floats and protects life below. Dissolving salt raises water's density enough to float an egg. Changing an object's shape does not change its density.

Read the full lesson

Privacy · Terms · Refunds · Delivery