- Advanced
- About 17 min
- 5 practice questions
Chain-growth polymerisation: radical, ionic and coordination routes
Choose the right chain-growth mechanism for a monomer, follow initiation to termination, and calculate chain length from initiator and termination mode.
If something looks wrong, please tell us.
At the advanced level, 'addition polymerisation' is not one process but four: free radical, cationic, anionic and coordination. Questions ask which mechanism suits a given monomer, what decides the chain length, and how the way chains stop changes the molar mass. This lesson assumes you already know the common addition polymers and their monomers, and goes underneath them.
Free radical chain growth
An initiator such as benzoyl peroxide splits on heating into two radicals. Initiation: a radical adds to the C=C of a monomer, making a new radical. Propagation: that radical adds monomer after monomer, very fast, so a long chain appears within a fraction of a second. Termination: two growing radicals meet. In combination (coupling) they join into one dead chain; in disproportionation one radical takes a hydrogen atom from the other, giving two dead chains, one with a saturated end and one with a double-bonded end. Chain transfer to solvent, monomer or an added agent stops one chain but starts another, and so lowers the average molar mass without lowering the rate much.
Ionic and coordination routes
| Route | Typical initiator | Monomers that suit it | Why |
|---|---|---|---|
| Cationic | Lewis acid (BF3, AlCl3) with a trace of water | Isobutylene, vinyl ethers | Electron-donating groups stabilise the carbocation |
| Anionic | n-Butyllithium, sodium amide | Acrylonitrile, methyl methacrylate, styrene | Electron-withdrawing groups stabilise the carbanion |
| Coordination | Ziegler-Natta: triethylaluminium + titanium tetrachloride | Ethene, propene | Monomer inserts at a metal centre: linear, stereoregular chains |
Anionic polymerisation in very pure conditions has no natural termination step: the chain ends stay active until a quencher is added. Such systems are called living polymers, and they allow block copolymers to be built by adding a second monomer after the first is used up. Ziegler-Natta catalysis gives linear high density polythene and isotactic polypropene, two results free radical routes cannot give.
Chain length from the initiator
Assume every radical starts one chain and every chain stops by one mode. Each benzoyl peroxide molecule gives two radicals, so 1 mol of initiator starts 2 mol of growing chains. If termination is by combination, every two growing chains become one dead chain; if by disproportionation, every growing chain becomes one dead chain. The average degree of polymerisation is then moles of monomer used ÷ moles of dead chains.
Worked example 1
0.010 mol of benzoyl peroxide fully decomposes, every radical starts a chain, and 10.0 mol of styrene polymerise. Find the average degree of polymerisation and molar mass if termination is (a) by combination, (b) by disproportionation. Radicals = 2 × 0.010 = 0.020 mol. (a) Combination: dead chains = 0.020 ÷ 2 = 0.010 mol; DP = 10.0 ÷ 0.010 = 1000; molar mass ≈ 1000 × 104 = 104,000 g/mol. (b) Disproportionation: dead chains = 0.020 mol; DP = 500; molar mass ≈ 52,000 g/mol. Initiator end groups are neglected because they are tiny compared with the chain.
Worked example 2
In the same system, a chain-transfer agent is added so that, on average, each radical generates three dead chains before termination: two by transfer and one by disproportionation. Dead chains = 3 × 0.020 = 0.060 mol, and DP = 10.0 ÷ 0.060 ≈ 167, molar mass ≈ 17,300 g/mol. The rate of monomer use is almost unchanged; only the chains are shorter. This is how manufacturers control molar mass.
Radicals = 2 × initiator. Combination: chains = radicals ÷ 2. Disproportionation: chains = radicals. DP = monomer used ÷ dead chains. Donating groups suit cationic, withdrawing groups suit anionic.
Key takeaways
- Combination doubles chain length compared with disproportionation for the same radicals.
- Chain transfer lowers molar mass, not the rate.
- Living anionic polymers have no termination and allow block copolymers.
- Ziegler-Natta gives linear and stereoregular chains.
Check your understanding
-
1. Which monomer is best suited to cationic polymerisation?
- Acrylonitrile
- Isobutylene
- Methyl methacrylate
- Tetrafluoroethene
Show answer
Answer: B. Isobutylene has two electron-donating methyl groups that stabilise the carbocation. Acrylonitrile and methyl methacrylate carry withdrawing groups and suit anionic routes.
-
2. 0.005 mol of benzoyl peroxide starts chains that use 5.0 mol of monomer; termination is by combination only. The average DP is:
- 500
- 250
- 2000
- 1000
Show answer
Answer: D. Radicals = 0.010 mol; combination gives 0.005 mol of chains. DP = 5.0 ÷ 0.005 = 1000.
-
3. Repeat the previous question with termination by disproportionation only. The DP is:
- 500
- 1000
- 2000
- 250
Show answer
Answer: A. Radicals = 0.010 mol, each giving one dead chain: 0.010 mol. DP = 5.0 ÷ 0.010 = 500.
-
4. Adding a chain-transfer agent to a radical polymerisation mainly:
- Increases the average molar mass
- Stops the reaction
- Lowers the average molar mass
- Makes the polymer isotactic
Show answer
Answer: C. Each transfer ends one chain and starts another, so more, shorter chains form from the same monomer.
-
5. 'Living polymers' are associated with:
- Free radical polymerisation in air
- Anionic polymerisation with no termination step
- Condensation polymerisation
- Vulcanisation
Show answer
Answer: B. In pure anionic systems the carbanion ends remain active until deliberately quenched, so chains can keep growing when more monomer is added.
Sign in to keep track of the lessons you finish.