Revision notes

Chapter 4 Geometric Constructions: Foundation

The key points, rules to remember, tables and diagrams from all 5 lessons, on one page for quick revision. To keep a copy, use your browser's Print and choose "Save as PDF".

Lesson 1

Basic constructions you will need

The tools of this chapter
ConstructionMethod in briefWhy it works
Perpendicular bisector of ABArcs of equal radius (more than half AB) from A and B on both sides; join their meeting pointsPoints equidistant from A and B lie on the perpendicular bisector
Line through P parallel to lDraw any line through P meeting l; copy the angle it makes with l at P, in the corresponding positionEqual corresponding angles give parallel lines
Angle equal to a given angleArc from the vertex cuts both arms; same arc from the new vertex; copy the chord lengthThe two small triangles are congruent by SSS
Triangle with sides a, b, cDraw one side; arcs of the other two lengths from its endsThe meeting point is at the right distance from both ends
Perpendicular to a line at a point on itEqual arcs on both sides of the point, then the perpendicular bisector of that segmentSame as the perpendicular bisector

Dividing AB into n equal parts

  1. Draw a ray AX At an acute angle to AB.
  2. Mark n equal steps With one compass opening: A₁, A₂, ..., Aₙ on AX.
  3. Join Aₙ to B The last mark to the far end of the segment.
  4. Draw parallels Through A₁, A₂, ... parallel to AₙB; they cut AB into n equal parts.

Every construction in this chapter rests on two ideas: parallel lines cut transversals proportionally, and copied angles (by SSS) are equal.

— Geometric constructions

Key takeaways: practise the perpendicular bisector, parallel through a point, copying an angle and the triangle from three sides until they are quick and neat. To divide a segment equally or in a ratio, step off equal parts on a slanting ray and draw parallels. Always check a construction by measuring.

Read the full lesson

Lesson 2

Constructing a triangle similar to a given triangle: separate triangles

Similar triangle with no common vertex

  1. Rough figure Sketch both triangles and label corresponding vertices in the same order.
  2. Analysis Write AB/PQ = BC/QR = AC/PR = given ratio.
  3. Calculate Find each unknown side; angles stay the same.
  4. Construct the given triangle From its data.
  5. Construct the new triangle From the calculated sides (and copied angle if needed).
Reading the ratio
Given ratio (given : new)New side = given side ×New triangle is
3 : 22/3smaller
3 : 44/3bigger
5 : 44/5smaller
7 : 55/7smaller

For △ABC ~ △PQR with AB : PQ = m : n, every side of △PQR is n/m times the corresponding side of △ABC, and the corresponding angles are equal.

— Similar triangle construction

Key takeaways: for separate triangles, calculate first and construct second. A ratio given : new greater than 1 makes the new triangle smaller; less than 1 makes it bigger. Copy angles exactly, scale only the sides.

Read the full lesson

Lesson 3

Constructing a similar triangle with a common vertex

Steps for the smaller triangle

  1. Construct any △ABC Or the given triangle.
  2. Divide BC into 4 equal parts Use a ray from B on the side away from A, with 4 equal steps.
  3. Mark C′ at the end of the 3rd part So BC′ = (3/4) BC.
  4. Through C′ draw a line parallel to CA It meets AB at A′.
  5. △A′BC′ is required Its sides are 3/4 of those of △ABC.

Smaller or bigger?

  • New triangle smaller (e.g. 4 : 3)
    • Divide BC into 4 parts
    • C′ is inside BC, at 3 parts
    • A′ is on side AB
  • New triangle bigger (e.g. 3 : 5)
    • Divide BC into 3 parts
    • C′ is on BC extended, at 5 parts
    • A′ is on BA extended

Common-vertex method: divide BC into as many equal parts as the larger number of the ratio's denominator, locate C′, and draw C′A′ parallel to CA.

— Similar triangle with a common vertex

Key takeaways: with a common vertex, no side needs calculating. Divide BC into the number of parts given by the original triangle's term of the ratio, place C′ at the new triangle's number of parts, and draw a parallel to CA. Extend the sides when the new triangle is bigger.

Read the full lesson

Lesson 4

Tangent at a point on a circle

Tangent at P using the centre C

  1. Draw the circle with centre C Take any point P on it.
  2. Draw ray CP Extend it beyond P to a point X.
  3. Construct a perpendicular to ray CX at P Equal arcs on both sides of P, then their perpendicular bisector.
  4. Name it line l Line l is the tangent at P.

Using the centre: tangent ⊥ radius at P. Without the centre: copy an inscribed angle onto the chord at C; the new arm is the tangent (converse of the tangent-secant angle theorem).

— Tangent at a point on a circle

Key takeaways: only one tangent passes through a point on a circle. With the centre, draw the perpendicular to the radius. Without the centre, use a chord and an inscribed angle, and copy that angle at the point between the chord and the new line. Tangents at the ends of a diameter are parallel.

Read the full lesson

Lesson 5

Tangents from a point outside a circle

Constructing tangents from an external point P

  1. Draw the circle with centre O Take a point P outside it.
  2. Join OP and bisect it The perpendicular bisector gives the midpoint M.
  3. Draw a circle with centre M and radius MO It passes through O and P.
  4. Mark A and B Where the two circles intersect.
  5. Draw lines PA and PB These are the required tangents.
Where is the point, and how many tangents?
Position of PNumber of tangents through P
Inside the circle0
On the circle1
Outside the circle2 (and they are equal)

The points of contact of the tangents from P are the intersections of the given circle with the circle drawn on OP as diameter.

— Tangents from an external point

Key takeaways: bisect OP, draw the circle on OP as diameter, and join P to the two intersection points. The right angle in the semicircle makes each line perpendicular to a radius, hence a tangent. Check by computing PA = √(OP² − r²).

Read the full lesson

Privacy · Terms · Refunds · Delivery