• Advanced
  • About 14 min
  • 5 practice questions

Stress, strain and Young's modulus

Calculate extension, stored energy and compare wires using Young's modulus, and read the stress-strain curve.

If something looks wrong, please tell us.

Solids resist deformation. Stress and strain describe this resistance independent of the sample's size, so the modulus is a property of the material, not of the particular wire.

Definitions

  • Stress = force / area (unit pascal, Pa).
  • Longitudinal strain = change in length / original length (no unit).
  • Hooke's law: within the elastic limit, stress ∝ strain.
  • Young's modulus Y = stress / strain = F L / (A ΔL).
  • Elastic potential energy stored in a stretched wire U = (1/2) F ΔL = (1/2) × stress × strain × volume.

From Y = F L / (A ΔL), the extension is ΔL = F L / (A Y). For the same material and force, ΔL ∝ L / r², since A = π r².

Worked example 1: extension of a wire

A steel wire 2 m long and 1 mm in diameter carries a load of 100 N. Take Y = 2 × 10¹¹ Pa. A = π (0.5 × 10⁻³)² = 7.85 × 10⁻⁷ m². ΔL = 100 × 2 / (7.85 × 10⁻⁷ × 2 × 10¹¹) = 200 / (1.57 × 10⁵) = 1.27 × 10⁻³ m, which is about 1.3 mm. Stored energy = (1/2) × 100 × 1.27 × 10⁻³ ≈ 0.064 J.

Worked example 2: comparing wires

Wire A has length L and radius r. Wire B is of the same material with length 2L and radius 2r. Under the same load, ΔL ∝ L / r². For B: ΔL_B / ΔL_A = (2 / 4) = 1/2. So B stretches half as much as A. The stiffness of a wire (force per unit extension) is k = A Y / L, so B is twice as stiff.

On a stress-strain curve, the straight part is the Hooke's-law region, the elastic limit marks where permanent deformation begins, and the breaking stress is the maximum stress the wire can bear before it fails.

Y = FL/(AΔL). ΔL = FL/(AY) ∝ L/r². Stored energy = (1/2) F ΔL = (1/2) stress × strain × volume. Spring constant of a wire k = AY/L.

— Formulas to remember

Key takeaways

  • Young's modulus belongs to the material; stiffness belongs to the wire.
  • Extension scales as L / r² for a given force and material.
  • Stored energy equals half of force times extension.

Check your understanding

  1. 1. A wire of cross-section 1 mm² is stretched by a force of 100 N. What is the stress?

    1. 10² Pa
    2. 10⁸ Pa
    3. 10⁵ Pa
    4. 10¹⁰ Pa
    Show answer

    Answer: B. 1 mm² = 10⁻⁶ m². Stress = 100 ÷ 10⁻⁶ = 10⁸ Pa. Forgetting to convert mm² to m² gives the wrong 10² Pa.

  2. 2. A steel wire 2 m long and 1 mm in diameter carries a load of 100 N. Taking Y = 2 × 10¹¹ Pa, what is its extension?

    1. About 0.32 mm
    2. 1.0 mm
    3. About 2.5 mm
    4. About 1.3 mm
    Show answer

    Answer: D. Radius = 0.5 mm, so A = π(0.5 × 10⁻³)² ≈ 7.85 × 10⁻⁷ m². ΔL = FL ÷ (AY) = 200 ÷ (7.85 × 10⁻⁷ × 2 × 10¹¹) = 200 ÷ 1.57 × 10⁵ ≈ 1.27 × 10⁻³ m ≈ 1.3 mm. Using the diameter as the radius gives the wrong 0.32 mm.

  3. 3. Wire A has length L and radius r. Wire B, of the same material, has length 2L and radius 2r. Under the same load, wire B stretches:

    1. Half as much as A
    2. Twice as much as A
    3. Four times as much as A
    4. The same as A
    Show answer

    Answer: A. ΔL ∝ L/r². For B: 2L/(2r)² = 2L/4r² = ½ × L/r². So B stretches half as much as A (and is twice as stiff).

  4. 4. A wire is cut to half its length and the same load is hung from it. How does the extension change?

    1. It doubles
    2. It stays the same
    3. It halves
    4. It becomes one quarter
    Show answer

    Answer: C. ΔL = FL ÷ (AY) is proportional to L for the same load, material and area, so halving L halves the extension.

  5. 5. A wire stretches by 2 mm under a load of 200 N. How much elastic energy does it store?

    1. 0.4 J
    2. 200 J
    3. 0.2 J
    4. 0.1 J
    Show answer

    Answer: C. U = ½ F ΔL = ½ × 200 × 0.002 = 0.2 J. Leaving out the ½ gives 0.4 J.

Privacy · Terms · Refunds · Delivery