• Advanced
  • About 17 min
  • 5 practice questions

Missile flight in depth: trajectory phases, re-entry, hypersonics and multiple warheads

Analyse the boost, midcourse and terminal phases of ballistic flight, explain staging, re-entry heating, canisters and multiple warheads, and compare hypersonic glide vehicles with hypersonic cruise missiles.

If something looks wrong, please tell us.

Advanced questions on missiles rarely ask for a name. They describe a behaviour - a missile that sheds stages, a warhead that glows on re-entry, a vehicle that glides at hypersonic speed - and ask you to reason about it. This lesson takes the ballistic-versus-cruise idea from the earlier courses and opens it up phase by phase, then explains why hypersonic weapons are discussed so much.

The three phases of ballistic flight

Phases of a ballistic missile's flight
PhaseWhat happensWhy it matters for defence
BoostRocket stages burn and accelerate the missile upwardThe hot exhaust plume is bright in infrared and easy to detect, but the phase is short and close to the launcher
MidcourseThe missile, now unpowered, coasts along its arc; for long ranges this is above most of the atmosphereThe longest phase; without air drag, light decoys travel alongside heavy warheads and are hard to tell apart
TerminalThe warhead re-enters the atmosphere and falls on the target at very high speedLittle time to react; air drag now separates decoys from warheads

Staging, propellants and canisters

Long-range ballistic missiles are built in stages. When the propellant of one stage is used up, its empty casing is dropped, so the remaining stages do not carry dead weight and the missile reaches a higher final speed and longer range. Strategic missiles increasingly use solid propellant, because a solid motor can be stored fuelled for long periods and fired at short notice; liquid propellants allow throttling but need more careful handling. A canister is a sealed tube in which a missile is stored, transported and launched. Canisterisation protects the missile from weather and handling and shortens the time needed to launch it, which improves readiness and survivability.

Re-entry heating

A warhead returning from space meets the atmosphere at very high speed. The air in front of it is compressed and heated intensely, so the re-entry vehicle needs a heat shield. A common design uses ablative material, which chars and wears away in a controlled manner, carrying heat away with it. Re-entry technology is a major test of whether a long-range missile actually works.

One missile, several warheads

A multiple independently targetable re-entry vehicle (MIRV) system lets one missile carry several warheads, each released by a manoeuvring "bus" towards a different target. MIRVs multiply the effect of a single launch and complicate missile defence, because one interceptor engagement must now deal with several incoming objects.

Hypersonic weapons: two different families

PointHypersonic glide vehicleHypersonic cruise missile
PropulsionBoosted by a rocket, then glides without powerPowered throughout by a scramjet
PathGlides through the upper atmosphere, not a simple arcFlies within the atmosphere under power
Shared difficulty for the defenderSpeed above Mach 5 combined with manoeuvring and a flatter path, so radars see it later and its course is hard to predictThe same
Shared engineering challengeExtreme heating; hot ionised air around the body can disturb communicationThe same, plus keeping combustion going in supersonic airflow

Worked examples

Example 1. Statement: "A ballistic missile is most easily separated from its decoys during the midcourse phase." True or false? Working: in midcourse the objects are above most of the atmosphere, where there is almost no air drag, so a light decoy and a heavy warhead move together. They separate once air drag acts on re-entry, in the terminal phase. The statement is false.

Example 2. Why is a hypersonic glide vehicle harder to defend against than a ballistic warhead of similar speed? Working: a ballistic warhead follows a predictable arc after its motor stops, so its impact point can be calculated early. A glide vehicle flies a flatter path through the upper atmosphere, appearing later over the horizon, and can manoeuvre, so its target cannot be predicted from its early path.

Boost: bright and short. Midcourse: long and decoy-friendly. Terminal: fast and brief. Hypersonic danger = speed + manoeuvre + late detection.

Key takeaways: ballistic flight has boost, midcourse and terminal phases, each with different detection and interception problems. Staging sheds dead weight; solid propellant and canisters improve readiness. Re-entry demands heat shields. MIRVs put several warheads on one missile. Hypersonic glide vehicles and hypersonic cruise missiles share speed and manoeuvre but differ in propulsion.

Check your understanding

  1. 1. Consider: (1) In the boost phase, a missile's exhaust plume makes it easy to detect in infrared. (2) The midcourse phase is usually the shortest phase of a long-range ballistic missile's flight. (3) Air drag in the terminal phase helps separate decoys from warheads. Which are correct?

    1. 1 and 2 only
    2. 2 and 3 only
    3. 1 and 3 only
    4. 1, 2 and 3
    Show answer

    Answer: C. Statement 1 is correct: the hot plume is bright in infrared. Statement 2 is wrong: midcourse is the longest phase. Statement 3 is correct: once in the atmosphere, light decoys slow down faster than heavy warheads.

  2. 2. The main reason long-range missiles use several stages is to:

    1. Make the missile easier to see on radar
    2. Drop the empty casings so the remaining stages carry less dead weight and reach higher speed
    3. Let the missile land and be reused
    4. Allow the missile to use air-breathing engines in space
    Show answer

    Answer: B. Discarding spent stages removes dead weight, so the remaining propellant accelerates a lighter vehicle to a higher final speed and range.

  3. 3. An ablative heat shield on a re-entry vehicle works by:

    1. Reflecting all radar waves
    2. Cooling the warhead with liquid nitrogen
    3. Increasing the vehicle's speed
    4. Charring and wearing away in a controlled way, carrying heat away from the vehicle
    Show answer

    Answer: D. Ablative materials absorb heat as they char and erode, and the removed material carries heat away, protecting what lies beneath during re-entry.

  4. 4. Which statement correctly distinguishes a hypersonic glide vehicle from a hypersonic cruise missile?

    1. The glide vehicle is boosted by a rocket and then glides unpowered; the cruise missile is powered throughout, typically by a scramjet
    2. The glide vehicle is subsonic; the cruise missile is hypersonic
    3. The glide vehicle uses a turbofan; the cruise missile uses no engine at all
    4. Both follow a simple ballistic arc
    Show answer

    Answer: A. A hypersonic glide vehicle is carried to speed and height by a rocket and then glides; a hypersonic cruise missile keeps an air-breathing engine, typically a scramjet, running through its flight.

  5. 5. A MIRV system allows:

    1. A missile to be launched from a submarine
    2. One missile to carry several warheads aimed at different targets
    3. A cruise missile to fly at hypersonic speed
    4. A radar to track several aircraft at once
    Show answer

    Answer: B. MIRV stands for multiple independently targetable re-entry vehicles: several warheads on one missile, each directed at its own target.

Privacy · Terms · Refunds · Delivery