• Practice
  • About 18 min
  • 5 practice questions

Techniques of plant tissue culture: sterilization, media, callus and hardening

Describe how glassware, media, rooms and explants are sterilized, the composition and preparation of MS and other media, the culture conditions, and the steps from callus induction to embryoids and hardening.

If something looks wrong, please tell us.

By the end of this lesson you can

  • Describe sterilization of tools, culture room, media and explants.
  • Name common media and explain the role of agar, sucrose and hormones.
  • State the culture conditions: pH, temperature, light, humidity, aeration.
  • Trace the steps from explant to a hardened plant.

Tissue culture succeeds or fails on details: a medium a little too acidic, an autoclave run cut short, or a plantlet moved too quickly into open air can waste weeks of work. This lesson follows the standard steps.

1. Sterilization

Sterilization steps
WhatHow (as given in the Tamil Nadu textbook)
Glassware, forceps, scalpelsWet steam in an autoclave at 15 psi (121 °C) for 15-30 minutes, or dipping in 70% ethanol followed by flaming and cooling
Culture roomFloor and walls washed with detergent, then 2% sodium hypochlorite or 95% ethanol; laminar air-flow cabinet wiped with 95% ethanol and exposed to UV for 15 minutes
Culture mediaDispensed in glass vessels, plugged with non-absorbent cotton or closures, autoclaved at 121 °C for 15-30 minutes
Heat-sensitive additivesPlant extracts, vitamins, amino acids and hormones are filter-sterilised through a fine membrane filter and added inside the laminar air-flow chamber
ExplantsWashed in running tap water, then surface-sterilised with agents such as 0.1% mercuric chloride or 70% ethanol under aseptic conditions

2. Media preparation

No single medium suits every tissue. The most common is MS medium (Murashige and Skoog, 1962); others are B5 (Gamborg et al., 1968), White's medium (1943) and Nitsch's medium (1969). A medium supplies inorganic macro- and micronutrients, a carbon source (sucrose - about 30 g per litre in MS, according to the textbook's appendix), vitamins, myo-inositol and plant growth regulators (auxins, cytokinins). It may be liquid, semi-solid or solid; agar, a mucilaginous polysaccharide from seaweeds, is the usual gelling agent (about 8 g per litre).

3. Culture conditions

  • pH: adjusted to 5.6-6.0.
  • Temperature: constant 25 °C ± 2 °C.
  • Humidity and light: 50-60% relative humidity; a 16-hour photoperiod under cool white fluorescent light of about 1000 lux.
  • Aeration: for liquid cultures, by automatic shakers or by bubbling filter-sterilised air.

4. From explant to plant

Basic steps in plant tissue culture

  1. Explant 1-2 cm sterile piece of leaf, stem, tuber or root
  2. Inoculation Placed on MS medium with auxin
  3. Callus induction 25 ± 2 °C, alternate light and dark; unorganised cell mass forms
  4. Embryogenesis Callus differentiates somatic embryos (embryoids)
  5. Plantlets Embryoids sub-cultured into plantlets
  6. Hardening Gradual exposure to normal conditions

Hardening is the gradual exposure of in vitro plantlets, first in humid chambers under diffused light in a greenhouse, to normal field conditions. Plantlets grown in glass have thin cuticles and weak stomatal control, so moving them straight into the open would make them lose water and wilt.

Autoclave: 121 °C, 15 psi, 15-30 min. Medium pH 5.6-6.0. Culture at 25 ± 2 °C. Heat-sensitive additives are filter-sterilised, not autoclaved.

Worked example 1: preparing a medium

A student must prepare 750 mL of medium containing sucrose at 30 g/L and agar at 8 g/L. How much of each is needed? Working: 750 mL = 0.75 L. Sucrose = 30 × 0.75 = 22.5 g. Agar = 8 × 0.75 = 6 g. Check: for 1 L the amounts would be 30 g and 8 g; three quarters of these are 22.5 g and 6 g.

Worked example 2: diluting a stock

A hormone stock solution contains 1 mg/mL. How much is needed to give 2 mg/L in 500 mL of medium? Working: amount needed = 2 mg/L × 0.5 L = 1 mg. Volume of stock = 1 mg ÷ 1 mg/mL = 1 mL. This stock is filter-sterilised and added after autoclaving, because many hormones and vitamins are damaged by heat.

Worked reasoning example 3: find the error

A medium's pH was set to 4.2 and the cultures failed to grow; the agar also stayed soft. What went wrong? Reasoning: the textbook's working range is 5.6-6.0; at much lower pH plant cells grow poorly and agar does not set firmly. Adjusting the pH to the correct range before autoclaving corrects both problems.

Key takeaways: tools, rooms, media and explants are each sterilised in a specific way (autoclave at 121 °C, ethanol, hypochlorite, UV, filter sterilisation, mercuric chloride); MS medium is most widely used, with sucrose, vitamins, hormones and agar; cultures need pH 5.6-6.0, 25 ± 2 °C, light and humidity control; the steps run from explant to callus, embryoids, plantlets and hardening.

Check your understanding

  1. 1. Media are sterilised in an autoclave at:

    1. 121 °C and 15 psi for 15-30 minutes
    2. 100 °C for 5 minutes
    3. 196 °C and 30 psi for 1 hour
    4. 60 °C overnight
    Show answer

    Answer: A. The textbook gives 15 psi (121 °C) for 15 to 30 minutes for wet-steam sterilization of media and glassware.

  2. 2. Why are vitamins and hormones usually filter-sterilised rather than autoclaved?

    1. They are too sticky to autoclave
    2. Many of them are destroyed by the heat of autoclaving
    3. They contain no microbes
    4. Autoclaving makes them more active
    Show answer

    Answer: B. Heat-labile substances break down at 121 °C, so they are passed through a fine filter that removes microbes and are added to the cooled sterile medium under aseptic conditions.

  3. 3. The usual pH range for plant tissue culture media is:

    1. 3.0 to 4.0
    2. 7.5 to 8.5
    3. 9.0 to 10.0
    4. 5.6 to 6.0
    Show answer

    Answer: D. The Tamil Nadu textbook states that the medium's pH is normally adjusted between 5.6 and 6.0.

  4. 4. How much agar is needed to make 250 mL of medium at 8 g/L?

    1. 8 g
    2. 0.8 g
    3. 2 g
    4. 32 g
    Show answer

    Answer: C. 250 mL = 0.25 L. 8 g/L × 0.25 L = 2 g.

  5. 5. Gradual exposure of in vitro plantlets to normal field conditions is called:

    1. hardening
    2. inoculation
    3. callus induction
    4. dedifferentiation
    Show answer

    Answer: A. Hardening (acclimatisation) moves plantlets through humid, shaded conditions so that they can survive in the open field.

Privacy · Terms · Refunds · Delivery