- Practice
- About 15 min
- 5 practice questions
Geomorphic processes and plate tectonics
Distinguish endogenetic from exogenetic processes, explain plate tectonics and the three kinds of plate boundary, and describe how folding and the Indian Plate built the Himalayas.
If something looks wrong, please tell us.
By the end of this lesson you can
- Distinguish internal (endogenetic) from external (exogenetic) processes.
- Explain plate tectonics and describe convergent, divergent and transform boundaries.
- Explain folding, faulting and how the Indian Plate's movement formed the Himalayas.
Mountains rise and plains are worn down, but too slowly for us to see in a lifetime. Two sets of forces are at work: one pushing up from inside the Earth and one wearing down from outside. This lesson covers the internal forces, which are the subject of this chapter.
Geomorphic processes
Endogenetic (internal) processes are forces that act from the Earth's interior towards the surface. They build the landscape and create relief such as mountains and plateaus. The principal source of their energy is the heat from radioactivity deep inside the Earth. Exogenetic (external) processes are forces acting on the surface through natural agents such as running water, glaciers, wind and waves. They wear down the landscape built by internal forces into lower plains. The next chapter studies the external processes.
Internal and external processes
-
Endogenetic (internal)
Act from inside the Earth
- Build landforms
- Powered by internal heat (radioactivity)
- Folding, faulting, earthquakes, volcanoes
-
Exogenetic (external)
Act on the surface
- Wear landforms down
- Agents: rivers, glaciers, wind, waves
- Weathering, erosion, deposition
Plate tectonics
The lithosphere is broken into huge slabs of rock called tectonic plates, both major and minor. These plates move independently over the mantle beneath them. The movement is driven by thermal (heat) energy from the mantle. Where plates collide, they produce mountain ranges and other uneven features on land and on the ocean floor. This whole idea is called plate tectonics, and it also explains where earthquakes and volcanoes occur.
Three kinds of plate boundary
Types of plate boundaries
-
Convergent
Plates move towards each other
- One plate may sink under another: a subduction zone
- Fold mountains, e.g. the Himalayas
- Trenches, volcanoes, earthquakes
-
Divergent
Plates pull away from each other
- Magma pushes up from the mantle
- New crust forms
- e.g. the Mid-Atlantic Ridge
-
Transform (conservative)
Plates slide past each other sideways
- Crust is neither made nor destroyed
- Mainly earthquakes
- e.g. the San Andreas Fault, USA
Folding and faulting
When plates push against each other, sideways (lateral) compression bends rock layers up and down into wave-like folds. This is folding, and mountains formed this way are fold mountains, such as the Himalayas and the Alps. When movement instead stretches rocks or puts them under so much stress that they crack and the blocks shift along the crack, the break is called a fault.
How the Himalayas were born
Plates move only a few centimetres a year on average, but over millions of years that adds up to thousands of kilometres. According to the textbook, about 250 million years ago the Indian Plate was part of a supercontinent called Gondwana (Gondwanaland), which also included today's Africa, Australia, Antarctica and South America. About 140 million years ago, it says, the Indian Plate broke away and moved north until it collided with the Eurasian Plate. The collision crumpled the crust into the Himalayan Mountains and raised the Tibetan Plateau.
From Gondwana to the Himalayas
- Indian Plate is part of Gondwana
- It breaks away and drifts north
- It collides with the Eurasian Plate
- Lateral compression folds the crust
- Himalayas and Tibetan Plateau rise
Convergent = plates meet (fold mountains, subduction); divergent = plates part (ridges, new crust); transform = plates slide past (earthquakes).
Worked example 1: Naming the boundary
Clue: 'Under the Atlantic Ocean, two plates move apart and magma rises to form an underwater mountain chain.' Step 1: moving apart means a divergent boundary. Step 2: rising magma forms new crust. Answer: a divergent boundary; the example is the Mid-Atlantic Ridge. If one plate were sinking beneath another, it would be convergent with a subduction zone.
Worked example 2: Rate times time
Suppose (an illustrative figure) a plate moves 5 cm every year. How far does it move in 1 million years? Step 1: 5 cm × 1,000,000 = 5,000,000 cm. Step 2: 100 cm = 1 m, so this is 50,000 m. Step 3: 1,000 m = 1 km, so it is 50 km. Over 100 million years, the same rate gives 5,000 km, which shows how a slow plate can cross an ocean.
Key takeaways: Endogenetic forces build landforms using internal heat; exogenetic forces wear them down. The lithosphere is broken into tectonic plates moved by heat from the mantle. Plates converge (subduction, fold mountains), diverge (ridges like the Mid-Atlantic Ridge) or slide past one another (San Andreas Fault). Folding made the Himalayas and Alps; the Indian Plate's drift north from Gondwana and its collision with Eurasia raised the Himalayas.
Check your understanding
-
1. The movement of tectonic plates is caused mainly by:
- Tidal energy
- Wind energy
- Thermal energy from the mantle
- Hydel energy
Show answer
Answer: C. Heat energy from the mantle drives the plates. Tides, wind and hydel power act at the surface and cannot move plates.
-
2. The place where one plate sinks beneath another at a convergent boundary is called a:
- Subduction zone
- Mid-ocean ridge
- Transform fault
- Crater
Show answer
Answer: A. At a convergent boundary a denser plate can sink under another; that sinking area is the subduction zone.
-
3. The San Andreas Fault is an example of which type of plate boundary?
- Convergent
- Divergent
- Subduction zone
- Transform
Show answer
Answer: D. At the San Andreas Fault the plates slide horizontally past each other, which is a transform (conservative) boundary.
-
4. Mountains like the Himalayas and the Alps were formed mainly by:
- Deposition by rivers
- Folding caused by lateral compression
- Erosion by wind
- Cooling of lava flows
Show answer
Answer: B. When plates push together, sideways compression bends rock layers into folds, forming fold mountains such as the Himalayas and Alps.
-
5. Suppose a plate moves 4 cm a year. How far does it move in 1 million years?
- 4 km
- 400 km
- 4,000 km
- 40 km
Show answer
Answer: D. 4 cm × 1,000,000 = 4,000,000 cm = 40,000 m = 40 km.
Sign in to keep track of the lessons you finish.