Chapter 8 Mechanical Properties of Solids
Practice questions
Taking the elastic limit of a rock as 3.0 × 10⁸ N m⁻², its density as 2.5 × 10³ kg m⁻³ and g = 10 m s⁻², the greatest height a mountain of this rock could have is about
- 1.2 km
- 8.3 km
- 30 km
- 12 km
Answer and explanation
Answer: D
The stress at the base, about hρg, must not exceed the elastic limit: h = (3.0 × 10⁸)/(2.5 × 10³ × 10) = 1.2 × 10⁴ m = 12 km.
A centrally loaded beam is replaced by one of the same material and length with twice the breadth and half the depth. The sag under the same load becomes
- 4 times as large
- the same
- one quarter
- 16 times as large
Answer and explanation
Answer: A
δ = Wl³/(4bd³Y), so δ ∝ 1/(b d³). New: 1/[(2b)(d/2)³] = 1/[2b × d³/8] = 4/(b d³). The sag is 4 times larger, which shows why depth matters more than breadth.
A steel wire (Y = 2.0 × 10¹¹ N m⁻²) has a strain of 2.0 × 10⁻³. What is the elastic energy stored per unit volume?
- 2.0 × 10⁵ J m⁻³
- 4.0 × 10⁸ J m⁻³
- 8.0 × 10⁵ J m⁻³
- 4.0 × 10⁵ J m⁻³
Answer and explanation
Answer: D
u = ½ Yε² = ½ × 2.0 × 10¹¹ × (2.0 × 10⁻³)² = ½ × 2.0 × 10¹¹ × 4.0 × 10⁻⁶ = 4.0 × 10⁵ J m⁻³. Forgetting the half gives 8.0 × 10⁵.
A steel wire 1.0 mm in diameter is stretched so that its longitudinal strain is 1.0 × 10⁻³. Its Poisson's ratio is 0.30. By how much does its diameter decrease?
- 3.0 × 10⁻⁴ mm
- 3.0 × 10⁻³ mm
- 1.0 × 10⁻³ mm
- 3.3 × 10⁻⁴ mm
Answer and explanation
Answer: A
Lateral strain = Poisson's ratio × longitudinal strain = 0.30 × 1.0 × 10⁻³ = 3.0 × 10⁻⁴. Δd = lateral strain × d = 3.0 × 10⁻⁴ × 1.0 mm = 3.0 × 10⁻⁴ mm.
What is the SI unit of compressibility?
- N m⁻²
- Pa⁻¹
- N m
- It has no unit
Answer and explanation
Answer: B
Compressibility k = 1/B. Bulk modulus is in Pa (N m⁻²), so k is in Pa⁻¹, that is m² N⁻¹. It is the fractional change in volume (no unit) per unit change in pressure.
A copper cube of edge 10 cm is placed where the pressure on it rises by 2.8 × 10⁷ Pa. Taking B(copper) = 1.4 × 10¹¹ Pa, by how much does its volume decrease?
- 0.020 cm³
- 2.0 cm³
- 0.20 cm³
- 20 cm³
Answer and explanation
Answer: C
ΔV/V = p/B = (2.8 × 10⁷)/(1.4 × 10¹¹) = 2.0 × 10⁻⁴. V = (10 cm)³ = 1000 cm³, so ΔV = 2.0 × 10⁻⁴ × 1000 = 0.20 cm³.
A steel wire 3.0 m long and 1.0 mm in radius carries a tension of 200 N. With Y = 2.0 × 10¹¹ N m⁻², its extension is closest to
- 0.095 mm
- 0.95 mm
- 9.5 mm
- 3.0 mm
Answer and explanation
Answer: B
A = π(1.0 × 10⁻³)² = 3.14 × 10⁻⁶ m². ΔL = FL/(AY) = (200 × 3.0)/(3.14 × 10⁻⁶ × 2.0 × 10¹¹) = 600/(6.28 × 10⁵) = 9.55 × 10⁻⁴ m, about 0.95 mm.
A wire is replaced by one of the same material with twice the length and twice the radius. For the same load, the extension becomes
- twice as large
- the same
- half as large
- four times as large
Answer and explanation
Answer: C
ΔL = FL/(πr²Y), so ΔL ∝ L/r². New value ∝ 2L/(2r)² = 2L/(4r²) = ½ (L/r²). The extension is halved.
A copper wire and a steel wire of the same length and cross-section are joined end to end and loaded. With Y(steel) = 2.0 × 10¹¹ and Y(copper) = 1.1 × 10¹¹ N m⁻², what is extension of copper ÷ extension of steel?
- 0.55
- 1.0
- 1.8
- 3.3
Answer and explanation
Answer: C
In series both wires carry the same tension F. ΔL = FL/(AY), and F, L and A are equal, so ΔL ∝ 1/Y. Ratio = Y(steel)/Y(copper) = 2.0/1.1 ≈ 1.8.
Assertion (A): Rubber is more elastic than steel. Reason (R): Rubber stretches much more than steel under the same stress.
- Both A and R are true, and R is the correct explanation of A
- Both A and R are true, but R is not the correct explanation of A
- A is true, but R is false
- A is false, but R is true
Answer and explanation
Answer: D
R is true: rubber has a far smaller modulus, so it stretches more. But in physics the more elastic material is the one that deforms less for a given stress (larger modulus), so steel is more elastic than rubber and A is false.
On a stress-strain graph (made-up data) the straight part passes through stress 1.0 × 10⁸ N m⁻² at strain 5.0 × 10⁻⁴. What is Young's modulus of the material?
- 5.0 × 10⁴ N m⁻²
- 2.0 × 10¹¹ N m⁻²
- 5.0 × 10¹¹ N m⁻²
- 2.0 × 10¹² N m⁻²
Answer and explanation
Answer: B
Y = slope of the straight part = stress/strain = (1.0 × 10⁸)/(5.0 × 10⁻⁴) = 0.2 × 10¹² = 2.0 × 10¹¹ N m⁻².
A wire is loaded beyond its yield point and then unloaded. Which statement is true?
- Its strain returns to zero because it is still elastic
- It is left with a permanent set: strain remains at zero stress
- Its Young's modulus has become zero
- It must already have fractured
Answer and explanation
Answer: B
Beyond the yield point (elastic limit) deformation is plastic. When the stress is removed the wire does not return to its original length: a permanent set remains. Fracture happens only at the end of the curve.
A wire hangs from a ceiling with a weight F at its lower end; its cross-sectional area is A. What is the tensile stress in the wire?
- 2F/A, because the ceiling and the weight both pull
- F/(2A)
- F/A
- Zero, because the two pulls cancel
Answer and explanation
Answer: C
The ceiling pulls up with F and the weight pulls down with F, but the tension at any cross-section is just F, not 2F. The stress is tension per unit area, F/A.
Which kind of stress changes the volume of a body but not its shape?
- Tensile stress
- Shearing stress
- Compressive stress on two opposite faces only
- Hydraulic stress
Answer and explanation
Answer: D
Hydraulic stress acts perpendicularly and equally on every part of the surface, so the body shrinks uniformly and keeps its shape. Tensile and compressive stress on two faces change the length; shearing stress changes the shape.
A rubber block 5.0 cm tall has its base fixed; a tangential force moves its top face 1.0 mm sideways. What is the shear angle?
- 0.20 rad
- 0.020 rad
- 0.0020 rad
- 2.0 rad
Answer and explanation
Answer: B
θ ≈ tan θ = Δx/L = 1.0 mm/50 mm = 0.020 rad. Both lengths are converted to millimetres before dividing.
Why are girders for bridges and buildings commonly made with an I-shaped cross-section?
- It gives depth to resist bending and a wide load-bearing surface while using less material, and it resists buckling better than a thin deep bar
- It is the only shape steel can be rolled into
- It increases the Young's modulus of steel
- It makes the beam bend more so it can absorb shocks
Answer and explanation
Answer: A
Sag falls steeply with depth (δ ∝ 1/d³), but a thin deep bar can buckle. The I-section keeps the depth, adds wide flanges to bear the load and removes metal where it does little work, cutting weight and cost. The shape does not change Y, which is a property of the material.
A crane rope of mild steel (yield strength 3.0 × 10⁸ N m⁻²) must hold 3000 kg without permanent stretch. Taking g = 9.8 m s⁻² and no safety margin, what is the least cross-sectional area?
- 1.0 × 10⁻⁵ m²
- 9.8 × 10⁻⁵ m²
- 3.3 × 10⁻⁴ m²
- 2.9 × 10⁻³ m²
Answer and explanation
Answer: B
A ≥ Mg/σy = (3000 × 9.8)/(3.0 × 10⁸) = 29400/(3.0 × 10⁸) = 9.8 × 10⁻⁵ m². A real crane would use about ten times this area as a safety margin.
A beam is supported at its ends and loaded at the centre. If its depth is doubled, keeping everything else the same, the sag becomes
- half
- one quarter
- one eighth
- twice as large
Answer and explanation
Answer: C
δ = Wl³/(4bd³Y), so δ ∝ 1/d³. Doubling d divides the sag by 2³ = 8.
A wire is under a stress of 2.0 × 10⁸ N m⁻² and a strain of 1.0 × 10⁻³. What is the elastic energy stored per unit volume?
- 2.0 × 10⁵ J m⁻³
- 5.0 × 10⁴ J m⁻³
- 2.0 × 10¹¹ J m⁻³
- 1.0 × 10⁵ J m⁻³
Answer and explanation
Answer: D
u = ½ × stress × strain = ½ × 2.0 × 10⁸ × 1.0 × 10⁻³ = 1.0 × 10⁵ J m⁻³.
A wire obeying Hooke's law is stretched by 2.0 mm by a final force of 200 N. How much elastic potential energy does it store?
- 0.40 J
- 0.20 J
- 400 J
- 0.10 J
Answer and explanation
Answer: B
The force rises steadily from 0 to 200 N, so U = ½ F l = ½ × 200 × 2.0 × 10⁻³ = 0.20 J. Using F × l without the half would double-count and give 0.40 J.