Unit 1 Metallurgy

Practice questions

Which refining method relies on impurities being more soluble in the melt than in the solid metal?

  1. Zone refining
  2. Liquation
  3. Mond process
  4. Distillation
Answer and explanation

Answer: A

Zone refining moves a molten zone along a rod; impurities stay in the melt and are swept to one end, leaving ultrapure Ge, Si or Ga behind. Liquation instead uses the low melting point of the metal itself.

A charge of 2.895 × 10⁵ C deposits how much aluminium in a Hall-Héroult cell? (Al = 27.0, F = 96,500 C mol⁻¹)

  1. 81.0 g
  2. 54.0 g
  3. 9.0 g
  4. 27.0 g
Answer and explanation

Answer: D

Moles of electrons = 2.895 × 10⁵ ÷ 96,500 = 3.00 mol. Al³⁺ + 3e⁻ → Al, so Al = 3.00 ÷ 3 = 1.00 mol = 27.0 g.

Sodium metal is obtained by electrolysis of

  1. aqueous NaCl, at the cathode
  2. fused NaCl, at the cathode
  3. fused NaCl, at the anode
  4. aqueous NaOH, at the anode
Answer and explanation

Answer: B

In aqueous NaCl the cathode reaction is 2H₂O + 2e⁻ → H₂ + 2OH⁻, so hydrogen, not sodium, forms (and the solution turns basic). Sodium is deposited at the cathode only from the molten salt: Na⁺ + e⁻ → Na.

For the forward reaction 2FeO → 2Fe + O₂ alone, ΔG° is large and positive. Why does adding carbon at 1500 K make reduction feasible?

  1. Carbon lowers ΔH° of FeO.
  2. Carbon is a catalyst.
  3. The very negative ΔG° of 2C + O₂ → 2CO outweighs the positive ΔG° of decomposing FeO.
  4. Carbon raises the melting point of iron.
Answer and explanation

Answer: C

Coupling adds the two ΔG° values. At 1500 K the CO line is well below the FeO line, so the sum is negative. Carbon is a reactant, not a catalyst.

Using the Ellingham diagram, which metal can reduce alumina?

  1. Fe
  2. Cu
  3. Mg
  4. Zn
Answer and explanation

Answer: C

The MgO line lies below the Al₂O₃ line (MgO is more stable), so magnesium can take oxygen from alumina. Fe, Cu and Zn have oxide lines above Al₂O₃.

Which statement about the Ellingham diagram is NOT true?

  1. The line for CO₂ formation is almost parallel to the free energy (y) axis.
  2. A sudden change of slope indicates a phase change.
  3. The negative slope of the CO line shows CO becomes more stable with temperature.
  4. The positive slope of metal-oxide lines shows their stability falls as temperature rises.
Answer and explanation

Answer: A

For C + O₂ → CO₂, ΔS° ≈ 0, so the line is almost horizontal, i.e. parallel to the temperature (x) axis, not the free-energy axis. The other three statements are correct.

For the coupled reaction 2FeO + 2C → 2Fe + 2CO, the illustrative values ΔG°(2Fe + O₂ → 2FeO) = −350 kJ and ΔG°(2C + O₂ → 2CO) = −460 kJ give ΔG° per mole of FeO of

  1. −110 kJ
  2. −55 kJ
  3. +55 kJ
  4. −405 kJ
Answer and explanation

Answer: B

Reverse the FeO reaction: +350 kJ. Add the CO reaction: 350 + (−460) = −110 kJ for 2 mol FeO, so −110 ÷ 2 = −55 kJ per mole of FeO.

Carbon cannot be used to reduce which oxide in practice?

  1. ZnO
  2. Cr₂O₃
  3. Fe₂O₃
  4. Al₂O₃
Answer and explanation

Answer: D

Al₂O₃ lies very low in the Ellingham diagram (very stable), and aluminium is extracted electrolytically. Carbon reduces ZnO, Cr₂O₃ and iron oxides at high temperature.

Blister copper gets its name because

  1. it is coated with CuO
  2. SO₂ escapes as it solidifies, leaving blisters
  3. it contains bubbles of CO₂ from limestone
  4. it is made by electrolysis
Answer and explanation

Answer: B

In the converter 2Cu₂O + Cu₂S → 6Cu + SO₂. The SO₂ gas bubbles out as the copper solidifies, giving it a blistered surface.

In the extraction of copper, silica is added to the reverberatory furnace to

  1. remove iron as FeSiO₃ slag
  2. reduce Cu₂O
  3. make the matte volatile
  4. absorb SO₂
Answer and explanation

Answer: A

Iron in the ore becomes basic FeO; silica, an acidic flux, combines with it: FeO + SiO₂ → FeSiO₃, a fusible slag. Copper stays in the matte as Cu₂S.

Which pair is matched WRONGLY?

  1. Calcination: ZnCO₃ → ZnO + CO₂
  2. Roasting: 2ZnS + 3O₂ → 2ZnO + 2SO₂
  3. Calcination: heating in excess of air
  4. Roasting: removes arsenic as volatile As₂O₃
Answer and explanation

Answer: C

Calcination is heating in the absence of air (or limited air). Heating in excess air is roasting, which also removes As as As₂O₃.

In the cementation step, 2[Au(CN)₂]⁻ + Zn → [Zn(CN)₄]²⁻ + 2Au, how many grams of zinc are needed to recover 3.94 g of gold? (Au = 197, Zn = 65.4)

  1. 0.327 g
  2. 1.31 g
  3. 13.1 g
  4. 0.654 g
Answer and explanation

Answer: D

Moles of Au = 3.94 ÷ 197 = 0.0200 mol. The equation uses 1 Zn per 2 Au, so Zn = 0.0100 mol = 0.0100 × 65.4 = 0.654 g.

When galena containing ZnS is concentrated, NaCN is added because it

  1. acts as the frothing agent
  2. converts PbS into a complex
  3. forms Na₂[Zn(CN)₄] on ZnS and stops it floating
  4. collects PbS particles
Answer and explanation

Answer: C

NaCN is a depressant: it coats zinc sulphide with the zinc cyanide complex so ZnS stays in the water while PbS rises with the froth.

Match: cyanide process, froth flotation, electrolytic reduction, zone refining with (i) ultrapure Ge, (ii) dressing of ZnS, (iii) extraction of Al, (iv) extraction of Au. The correct order is

  1. (iv), (ii), (iii), (i)
  2. (i), (ii), (iii), (iv)
  3. (iii), (iv), (ii), (i)
  4. (ii), (iii), (i), (iv)
Answer and explanation

Answer: A

Cyanide process → gold (iv); froth flotation → concentrating zinc blende (ii); electrolytic reduction → aluminium (iii); zone refining → ultrapure germanium (i).

Which statement about minerals and ores is correct?

  1. Every mineral is an ore.
  2. An ore is a mineral from which the metal can be extracted conveniently and economically.
  3. Ores contain no gangue.
  4. China clay is the main ore of aluminium.
Answer and explanation

Answer: B

All ores are minerals, but only those from which extraction is economic are ores; ores always carry gangue. Bauxite, not china clay, is the ore of aluminium.

How many coulombs are needed to deposit 10.8 g of silver from Ag⁺ during electrolytic refining? (Ag = 108 g mol⁻¹, F = 96,485 C mol⁻¹)

  1. 96,485 C
  2. 9,648.5 C
  3. 19,297 C
  4. 1,042 C
Answer and explanation

Answer: B

Moles of Ag = 10.8 ÷ 108 = 0.100 mol. Ag⁺ + e⁻ → Ag needs 1 mol electrons per mol Ag, so 0.100 mol e⁻. Q = 0.100 × 96,485 = 9,648.5 C.

Zr(impure) + 2I₂ → ZrI₄ at about 523 K, then ZrI₄ → Zr(pure) + 2I₂ at about 1800 K. This method is

  1. the Mond process
  2. zone refining
  3. liquation
  4. the Van Arkel method
Answer and explanation

Answer: D

Forming a volatile tetraiodide and decomposing it on a hot tungsten filament is the Van Arkel method, used for Zr and Ti. The Mond process uses CO to refine nickel.

In the electrolytic refining of copper, the anode is

  1. impure copper
  2. pure copper
  3. a carbon rod
  4. a platinum electrode
Answer and explanation

Answer: A

The impure metal is made the anode so that copper dissolves from it; pure copper deposits on the pure-copper cathode, and less electropositive impurities collect as anode mud.

In the Hall-Héroult process, cryolite is added mainly to

  1. remove impurities from alumina
  2. act as the anode
  3. lower the melting point of alumina and make the melt conduct
  4. reduce Al³⁺ chemically
Answer and explanation

Answer: C

Pure alumina melts at a very high temperature. Dissolving it in molten cryolite (with some CaCl₂) gives a melt that can be worked at about 1270 K and conducts electricity.

Which reaction is NOT feasible under standard conditions? (E°: Zn²⁺/Zn −0.76 V, Fe²⁺/Fe −0.44 V, Cu²⁺/Cu +0.34 V, Ag⁺/Ag +0.80 V)

  1. Zn + Cu²⁺ → Cu + Zn²⁺
  2. Cu + Zn²⁺ → Zn + Cu²⁺
  3. Cu + 2Ag⁺ → 2Ag + Cu²⁺
  4. Fe + Cu²⁺ → Cu + Fe²⁺
Answer and explanation

Answer: B

For Cu + Zn²⁺, E° = E°(Zn²⁺/Zn) − E°(Cu²⁺/Cu) = −0.76 − 0.34 = −1.10 V. A negative E° makes ΔG° = −nFE° positive, so copper cannot displace zinc. The other three have positive E° (1.10, 0.46 and 0.78 V).

Privacy · Terms · Refunds · Delivery