Revision notes

Chapter 12 Surface Areas and Volumes: Foundation

The key points, rules to remember, tables and diagrams from all 5 lessons, on one page for quick revision. To keep a copy, use your browser's Print and choose "Save as PDF".

Lesson 1

Basic solids revisited: the formulas you will combine

Basic solids in this chapter

  • Solids with flat faces
    • Cuboid: length l, breadth b, height h
    • Cube: every edge a
  • Solids with a curved surface
    • Cylinder: radius r, height h
    • Cone: radius r, height h, slant height l
    • Sphere: radius r
    • Hemisphere: half a sphere, radius r
Every combined solid in this chapter is built from these pieces.
Formulas to know by heart
SolidCurved / lateral surface areaTotal surface areaVolume
Cuboid2h(l + b)2(lb + bh + hl)l × b × h
Cube4a²6a²a³
Cylinder2πrh2πr(r + h)πr²h
Coneπrlπr(l + r)⅓πr²h
Sphere4πr²4πr²⁴⁄₃πr³
Hemisphere2πr²3πr²⅔πr³

Slant height of a cone: l = √(h² + r²). Areas are in square units (cm², m²); volumes are in cubic units (cm³, m³). 1 litre = 1000 cm³ and 1 m³ = 1000 litres.

Key takeaways: learn the six sets of formulas as a table; find the slant height of a cone with l = √(h² + r²) before using πrl; decide from the situation whether a flat face is part of the surface; keep units consistent and convert cm³ to litres by dividing by 1000. Every combined-solid question in the next lessons uses these formulas as building blocks.

Read the full lesson

Lesson 2

Surface area of solids joined together

Finding the surface area of a combined solid

  1. Break it into parts Name the basic solids, e.g. a cylinder with two hemispheres.
  2. Find the joins Which faces are glued together and hidden?
  3. List visible surfaces Usually curved surfaces, plus any flat face still showing.
  4. Calculate and add Find each visible area and add them.
Common combinations
ObjectPartsSurface area to add
Medicine capsuleCylinder + two hemispheresCSA of cylinder + 2 × CSA of hemisphere
Toy topCone on a hemisphereCSA of cone + CSA of hemisphere
Tent (no floor)Cylinder + cone on topCSA of cylinder + CSA of cone
Cube with a domeCube + hemisphere on one faceTSA of cube − πr² + 2πr²
Two cubes end to endCuboidTSA of both cubes − 2 hidden squares

Surface area of a combined solid = sum of the surfaces you can still see. Faces that are glued together are not counted.

Key takeaways: never simply add two total surface areas; list what is visible after joining; the height of the cone in a cone-on-hemisphere toy is the total height minus the radius; in a capsule the cylinder's length is the total length minus the diameter; for cost, multiply the area by the rate per unit area.

Read the full lesson

Lesson 3

Surface area when a part is scooped out

Joining solids vs scooping out

  • Joining (lesson 2)
    • Glued faces disappear
    • Add the outer surfaces still visible
    • Volume = sum of volumes
  • Scooping out (this lesson)
    • The opening circle disappears
    • The inner curved wall is added
    • Volume = big solid − removed part

Cut-out rule: surface area of remaining solid = original surface area − area of the opening + area of the new inner surface.

What changes in each case
SolidRemoveAdd
Cylinder with a cone hollowed from one endOne circular base (πr²)Cone's curved surface (πrl)
Cylinder with hemispheres scooped from both endsBoth circular bases (2πr²)Two hemispherical surfaces (4πr²)
Cube with a hemispherical depressionCircle on one face (πr²)Hemisphere's curved surface (2πr²)

Key takeaways: for a cut-out, remove the area of the opening and add the inner wall; the result can be larger than the original surface area; draw a quick sketch and tick each surface you can touch before calculating.

Read the full lesson

Lesson 4

Volume of a combination of solids

Volume of a combined solid = sum of the volumes of its parts. (For a hollowed solid, subtract the part removed.)

Finding the volume of a combined solid

  1. Split into basic solids Cylinder, cone, hemisphere, cuboid...
  2. Find each dimension Use total length or height to find the missing one.
  3. Find each volume Use the formula for each part.
  4. Add (or subtract a hollow) Give units: cm³, m³ or litres.
Ready formulas (H = height of cylinder, h = height of cone)
ObjectVolume
Cone on a hemisphere (same r)⅓πr²h + ⅔πr³
Cylinder with two hemispherical endsπr²h + ⁴⁄₃πr³
Cylinder with two conical endsπr²H + 2 × ⅓πr²h
Cylinder with a cone on topπr²H + ⅓πr²h
Cube with a hemisphere on topa³ + ⅔πr³

Key takeaways: volumes of joined parts simply add; two hemispheres of the same radius make one sphere; find hidden dimensions (such as the cylinder's length) from the totals; write answers with units and convert to litres when a capacity is asked.

Read the full lesson

Lesson 5

Volume problems: hollows, water left, counting and mass

Four kinds of volume problems

  • Material left
    • Block volume − volume of holes or hollows
  • Water left or displaced
    • Water left = vessel volume − volume of solid inside
    • Rise in level × base area = volume of objects added
  • Counting objects
    • Number = total volume ÷ volume of one object
  • Mass and cost
    • Mass = volume × mass of 1 cm³
    • Cost = volume × rate per unit

A solid fully under water pushes out (displaces) water equal to its own volume. Number of objects = total volume ÷ volume of one object.

Key takeaways: subtract volumes for holes and for water pushed out; use the rise in water level times the base area to find the volume added; divide total volume by the volume of one object to count; multiply volume by the given mass of 1 cm³ to find mass. Always check that a solid actually fits inside the vessel.

Read the full lesson

Privacy · Terms · Refunds · Delivery