- Foundation
- About 24 min
- 5 practice questions
Friction and the dynamics of circular motion
Apply the laws of static and kinetic friction, find the angle of repose, explain the uses of friction, and analyse cars on level and banked circular roads.
If something looks wrong, please tell us.
By the end of this lesson you can
- Distinguish static, limiting and kinetic friction, and use fₛ ≤ μₛN and f_k = μ_kN.
- Show that the angle at which a block begins to slide satisfies tan θ = μₛ.
- Explain rolling friction and ways of reducing or using friction.
- Identify the force that provides the centripetal force mv²/R in different situations.
- Derive the maximum safe speed on a level road and the optimum speed on a banked road.
Push a heavy box gently and it does not move; push harder and it suddenly starts sliding. Something along the floor must be opposing your push and growing with it. That force is friction, the component of the contact force along the surfaces in contact. Friction opposes relative motion, actual or impending, between surfaces.
Static and kinetic friction
While the box stays at rest, the friction fₛ exactly balances the applied force. It is self-adjusting: zero when nothing pushes, and growing as the push grows, up to a maximum, the limiting friction (fₛ)ₘₐₓ = μₛN, where N is the normal force and μₛ is the coefficient of static friction, which depends only on the pair of surfaces. So fₛ ≤ μₛN. Experiments show limiting friction is independent of the area of contact. Once sliding starts, the friction falls to the kinetic (sliding) friction f_k = μ_kN, also independent of the area and nearly independent of speed, with μ_k < μₛ. A sliding body then accelerates at (F − f_k)/m. These are empirical laws, approximately true, but very useful.
Friction as the applied force grows
- No push No static friction at all.
- Small push F Static friction fₛ = F; the body stays at rest.
- F reaches μₛN Limiting friction; motion is just about to start.
- F exceeds μₛN Body slides; friction drops to f_k = μ_kN, and a = (F − f_k)/m.
Friction can make things move. A box on the floor of an accelerating train moves with the train only because static friction from the floor pushes it forward. Its largest possible acceleration is when fₛ is at its limit: ma = μₛmg, so aₘₐₓ = μₛg. If the train accelerates faster, the box slides back relative to the floor.
Angle of repose
Place a block on a plank and slowly tilt the plank. Resolving the weight, the force down the slope is mg sin θ and the normal force is N = mg cos θ. Static friction balances mg sin θ until it reaches μₛN = μₛmg cos θ. At the angle θₘₐₓ where the block just begins to slide, mg sin θₘₐₓ = μₛmg cos θₘₐₓ, so tan θₘₐₓ = μₛ. This angle, independent of the block's mass, is the angle of repose.
Rolling friction; friction good and bad
An ideal wheel rolling without slipping touches the ground at a point that is momentarily at rest, so it would face no sliding friction. In practice the surfaces deform slightly and a small rolling friction remains, often hundreds of times smaller than sliding friction for the same load, which is why the wheel was such a major invention. Friction wastes energy as heat in machines, so we reduce it with lubricants, ball bearings and cushions of compressed air. But friction is also essential: we can walk, cars can accelerate, turn and brake, and nails and knots hold, all because of friction.
Centripetal force
A body moving in a circle of radius R at speed v has acceleration v²/R towards the centre, so by the second law the net force on it towards the centre must be f_c = mv²/R, the centripetal force. It is not a new kind of force: it is provided by tension (a stone on a string), gravity (a planet round the Sun) or friction (a car turning on a level road).
Level road. For a car on a flat circular turn, N = mg and the centripetal force must come from static friction: mv²/R = fₛ ≤ μₛmg. So v² ≤ μₛRg and vₘₐₓ = √(μₛRg), independent of the car's mass. Driving faster than this, the car skids outward.
Banked road. If the road is tilted at angle θ towards the centre, the normal force itself has a horizontal component N sin θ pointing inward. Vertical balance: N cos θ = mg + f sin θ. Inward: N sin θ + f cos θ = mv²/R. Setting f = μₛN for the largest speed and eliminating N gives vₘₐₓ = √[Rg(μₛ + tan θ)/(1 − μₛ tan θ)], larger than on a flat road. With no friction needed at all (μₛ = 0), the optimum speed is v₀ = √(Rg tan θ); driving at v₀ causes the least tyre wear. Below v₀, friction acts up the slope.
| Situation | Source of centripetal force | Key result |
|---|---|---|
| Stone whirled on a string | Tension in the string | T = mv²/R (horizontal circle, ignoring gravity's effect on the string) |
| Car on a level curve | Static friction from the road | vₘₐₓ = √(μₛRg) |
| Car on a banked curve | Horizontal parts of N and friction | v₀ = √(Rg tan θ) without friction |
| Planet round the Sun | Gravitational pull of the Sun | GMm/r² = mv²/r |
fₛ ≤ μₛN, f_k = μ_kN, μ_k < μₛ; tan θ (repose) = μₛ. Centripetal force mv²/R; level road vₘₐₓ = √(μₛRg); banked road v₀ = √(Rg tan θ).
Worked example 1: pushing a box
A 10 kg box rests on a floor with μₛ = 0.40 and μ_k = 0.30 (g = 9.8 m s⁻²). N = 98 N, so limiting friction = 0.40 × 98 = 39.2 N and kinetic friction = 0.30 × 98 = 29.4 N. Push of 30 N: less than 39.2 N, so the box stays at rest and the friction is exactly 30 N (not 39.2 N). Push of 50 N: the box slides and a = (50 − 29.4)/10 = 2.06 m s⁻².
Worked example 2: a car on a level curve
What is the greatest speed at which a car can take a flat curve of radius 40 m if μₛ = 0.50 (g = 9.8 m s⁻²)? vₘₐₓ = √(μₛRg) = √(0.50 × 40 × 9.8) = √196 = 14 m s⁻¹ (about 50 km h⁻¹). A cyclist doing 5.0 m s⁻¹ on a 3.0 m radius turn with μₛ = 0.10 needs v² = 25 m² s⁻² but μₛRg = 2.94 m² s⁻² only, so she will skid.
Worked example 3: a banked curve
A curve of radius 50 m is banked so that tan θ = 0.20 (θ ≈ 11°), and μₛ = 0.30. Optimum speed: v₀ = √(50 × 9.8 × 0.20) = √98 ≈ 9.9 m s⁻¹. Maximum speed: vₘₐₓ = √[50 × 9.8 × (0.30 + 0.20)/(1 − 0.30 × 0.20)] = √(245/0.94) = √260.6 ≈ 16 m s⁻¹. On a level road of the same radius and friction, vₘₐₓ would be √(0.30 × 50 × 9.8) ≈ 12 m s⁻¹, so banking helps.
Key takeaways
- Static friction adjusts itself up to μₛN; kinetic friction is μ_kN and is smaller.
- The angle of repose satisfies tan θ = μₛ, whatever the mass.
- Centripetal force is the net inward force (tension, friction, gravity), never an extra force.
- Banking lets the normal force supply part of the centripetal force, raising the safe speed.
Check your understanding
-
1. A 5.0 kg block rests on a horizontal surface with μₛ = 0.50. A horizontal push of 10 N is applied (g = 9.8 m s⁻²). The friction force on the block is:
- 24.5 N
- 10 N
- zero
- 49 N
Show answer
Answer: B. Limiting friction = μₛmg = 0.50 × 5.0 × 9.8 = 24.5 N. The push of 10 N is less than this, so the block stays at rest and static friction adjusts to exactly balance it: 10 N.
-
2. A block just begins to slide down a plank when the plank makes 30° with the horizontal. The coefficient of static friction is about:
- 0.50
- 0.87
- 0.58
- 1.73
Show answer
Answer: C. At the angle of repose, μₛ = tan θ = tan 30° ≈ 0.577, about 0.58.
-
3. A car takes a flat circular turn of radius 90 m. If μₛ = 0.40 and g = 9.8 m s⁻², its maximum safe speed is about:
- 18.8 m s⁻¹
- 35.3 m s⁻¹
- 6.0 m s⁻¹
- 353 m s⁻¹
Show answer
Answer: A. vₘₐₓ = √(μₛRg) = √(0.40 × 90 × 9.8) = √352.8 ≈ 18.8 m s⁻¹.
-
4. What provides the centripetal force for a car turning on a level (unbanked) road?
- The weight of the car
- The normal reaction of the road
- The engine force
- Static friction between the tyres and the road
Show answer
Answer: D. On a flat road the weight and normal force are vertical and cancel. The only horizontal force from the road towards the centre is static friction on the tyres, which provides mv²/R.
-
5. Assertion (A): The maximum safe speed of a car on a level circular road does not depend on the car's mass. Reason (R): Both the centripetal force needed and the maximum friction available are proportional to the mass.
- Both A and R are true, and R is the correct explanation of A.
- Both A and R are true, but R is not the correct explanation of A.
- A is true, but R is false.
- A is false, but R is true.
Show answer
Answer: A. Both are true. mv²/R ≤ μₛmg; the mass cancels, giving vₘₐₓ = √(μₛRg). R gives exactly this reason.
Sign in to keep track of the lessons you finish.