• Foundation
  • About 14 min
  • 5 practice questions

Using electromagnets: cranes, bells and motors

Explain how lifting electromagnets, electric bells, motors and loudspeakers use the magnetic effect of current, and reason about why an electromagnet stops working.

If something looks wrong, please tell us.

By the end of this lesson you can

  • Explain how a lifting electromagnet picks up and drops iron and steel.
  • Describe in simple steps how an electric bell rings.
  • Reason about faults in electromagnet devices.

Because an electromagnet can be switched on, switched off and made stronger, it is far more useful than a permanent magnet in many machines. Let us look at a few.

Lifting electromagnets

Strong electromagnets hang from cranes in factories and scrap yards. The operator switches the current on to lift iron and steel objects, moves the crane, and switches off to drop them exactly where needed. A permanent magnet could not do this: it would hold on to the scrap and never let go. Lifting magnets also help sort iron and steel from other metals such as aluminium and copper, which are not attracted.

Working cycle of a lifting electromagnet

  1. Current ON The electromagnet becomes a strong magnet
  2. Lift Iron and steel scrap is attracted and lifted
  3. Move The crane swings to the drop point
  4. Current OFF The magnetism disappears and the scrap falls

Then back to step 1: Current ON

Worked example 1: sorting scrap

A heap contains iron rods, aluminium cans and copper wire. What does a lifting electromagnet pick up? Working: only magnetic materials are attracted. Iron is magnetic; aluminium and copper are not. So it lifts the iron rods and leaves the aluminium and copper behind, separating them.

The electric bell

An electric bell uses an electromagnet that switches itself on and off very quickly.

How an electric bell rings

  1. Press the switch Current flows through the electromagnet's coil
  2. Electromagnet pulls It attracts an iron strip attached to a hammer, which strikes the gong
  3. Circuit breaks Moving the strip separates a contact, so the current stops
  4. Strip springs back With no magnetism, the strip returns and touches the contact again, so current flows and the cycle repeats

Then back to step 1: Press the switch

This on-off cycle repeats many times a second while the button is held, so the hammer strikes again and again and the bell rings continuously.

Motors and loudspeakers

An electric motor uses the magnetic effect of current to produce turning motion. Fans, mixers, washing machines, water pumps and electric vehicles all use motors. A loudspeaker uses a coil and a magnet: a changing current in the coil makes it move back and forth, and this moves a cone that pushes the air to make sound.

Devices using the magnetic effect of current
DeviceWhat the magnetic effect does
Lifting electromagnetPicks up iron and steel, releases them when switched off
Electric bellRepeatedly pulls a hammer onto a gong
Electric motor (fan, mixer, pump)Produces turning motion
LoudspeakerMoves a cone back and forth to make sound

A glimpse ahead

Electricity can produce magnetism; in higher classes you will learn that a moving magnet can also produce an electric current. This two-way link is the basis of electric generators in power stations as well as motors.

Worked example 2: why did the crane model stop?

Sumana leaves her nail-and-coil model switched on for a long time. Later the nail no longer lifts the clips, though the wire is still warm. Give reasons. Working: Step 1, the electromagnet needs enough current. Step 2, a coil connected for a long time drains the cell quickly, so the current becomes very small and the magnet becomes too weak to lift clips. Step 3, the warmth shows that current was flowing and some energy turned into heat (the heating effect, next lesson). Fix: use a fresh cell and switch on only when lifting.

Electromagnets are useful because they can be switched on and off, and their strength can be controlled.

Key takeaways: lifting electromagnets pick up iron and steel when current flows and release them when it stops, which also sorts magnetic from non-magnetic metals. An electric bell's electromagnet breaks and remakes its own circuit, so the hammer strikes repeatedly. Motors and loudspeakers also depend on the magnetic effect. A weak cell gives too little current, so an electromagnet loses strength.

Check your understanding

  1. 1. Why is an electromagnet, not a permanent magnet, used on scrap-yard cranes?

    1. It never needs electricity.
    2. It attracts aluminium cans.
    3. It can be switched off to release the load where needed.
    4. It cannot lift heavy objects.
    Show answer

    Answer: C. The operator turns the current on to lift and off to drop. A permanent magnet would keep holding the scrap.

  2. 2. A lifting electromagnet is lowered onto a pile of iron nails, copper wires and aluminium foil. Which will it lift?

    1. Only the copper wires
    2. Only the aluminium foil
    3. Only the iron nails
    4. All three
    Show answer

    Answer: C. Only magnetic materials such as iron are attracted. Copper and aluminium are not magnetic, so they stay behind.

  3. 3. In an electric bell, what happens just after the hammer is pulled to strike the gong?

    1. The current becomes permanently stronger.
    2. The bell turns into a permanent magnet.
    3. The gong produces electricity.
    4. The circuit breaks, the electromagnet stops working and the strip springs back.
    Show answer

    Answer: D. The moving strip separates from a contact, breaking the circuit. With no magnetism, the strip returns, remakes the contact and the cycle repeats.

  4. 4. Which household device uses the magnetic effect of electric current to produce turning motion?

    1. The motor in a ceiling fan
    2. An electric iron
    3. An immersion rod
    4. A filament bulb
    Show answer

    Answer: A. A motor turns because of the magnetic effect of current. Irons, immersion rods and filament bulbs use the heating effect.

  5. 5. An electromagnet model gets weaker over time while left switched on. Which is the most likely reason?

    1. The iron nail has turned into copper.
    2. The cell is running down, so less current flows.
    3. The coil has gained more turns.
    4. Electromagnets get stronger with time.
    Show answer

    Answer: B. Strength depends on current. A coil left connected drains the cell, the current falls and the magnet becomes weaker.

Sign in to keep track of the lessons you finish.

Next lesson → The heating effect of electric current

Privacy · Terms · Refunds · Delivery