• Foundation
  • About 15 min
  • 5 practice questions

Pressure in liquids

Show that a liquid exerts pressure that grows with the height of the liquid column and acts in all directions, and use this to explain overhead tanks and the shape of dams.

If something looks wrong, please tell us.

By the end of this lesson you can

  • Explain that liquid pressure depends on the height of the liquid column.
  • Show that liquids press on the sides of a container, in all directions.
  • Explain why water tanks are placed high and why dams have broad bases.

Why are water tanks placed on rooftops or tall towers? Why does water spurt from a leaking pipe? Both are answered by the pressure that liquids exert.

Pressure depends on height, not on width

Take two clear pipes of the same length but different widths. Tie a balloon over the bottom end of each, clamp them upright and fill both with water to the same height. Both balloons bulge by the same amount, even though the wide pipe holds much more water. So the bulge is not decided by the total weight of water but by the height of the water column. Now add more water to one pipe: its balloon bulges more. The taller the column, the greater the pressure at the bottom.

The pressure exerted by a liquid at the bottom of a column increases with the height (depth) of the liquid; for the same liquid and the same height, the pressure is the same whatever the width of the vessel.

Worked example 1: which floor gets the strongest flow?

A three-storey building has its water tank on the roof. Which tap gives the stronger stream: one on the second floor or one on the first floor? Working: the pressure at a tap depends on the height of water above it. The first-floor tap is further below the tank, so the water column above it is taller. Taller column, higher pressure, so the first-floor tap gives the stronger stream.

Liquids press sideways too

Make four small holes around a plastic bottle, all at the same height near the bottom, cover them with tape and fill the bottle. Remove the tape: water spurts out of all four holes equally. So water presses on the sides of the container as well as the bottom. In fact, liquids exert pressure in all directions. That is why water sprays out of a leaking joint in a pipe.

Liquid pressure acts

  • Downwards
    • On the bottom of the container
    • Makes the balloon at the base of a pipe bulge
  • Sideways
    • On the walls
    • Water spurts from side holes
  • Upwards
    • On objects in the liquid
    • Related to upthrust
in all directions at any point in the liquid

Tanks and dams

Using and resisting liquid pressure
StructureIdea used
Overhead tankA taller water column gives more pressure at the taps
Broad base of a damWater pressure on the wall is greatest at the bottom, where the water is deepest, so the wall is made thickest there
Water spurting from a leaking pipeWater presses outward on the pipe walls

Why a dam is broad at the base

  1. Water stored behind the dam The deeper the water, the higher the pressure
  2. Pressure greatest at the bottom It pushes hardest on the lowest part of the wall
  3. Thick, broad base Resists the large sideways push and supports the structure

Worked example 2: two vessels, same level

Vessel A is narrow and vessel B is wide; both hold water to the same height. Compare the pressure at the bottom and the total force on the bottom. Working: pressure depends only on height for the same liquid, so the pressure at the bottom is equal in A and B. Force = pressure × area; B has a bigger base area, so the total force on B's bottom is larger. So pressures are equal, but force on B is greater.

Worked example 3: raising a tank

A family on the ground floor wants a stronger flow from their taps. Should they raise the tank, or buy a wider tank at the same height? Working: pressure at the taps depends on the height of water above them, not the width of the tank. Raising the tank increases that height, increasing the pressure. A wider tank at the same height holds more water but gives the same pressure. So they should raise the tank.

Key takeaways: liquid pressure increases with the height of the liquid column and does not depend on the width of the vessel. Liquids press in all directions, including on the sides of containers. Overhead tanks are placed high to give good pressure at taps; dams have broad bases because pressure is greatest at the bottom.

Check your understanding

  1. 1. Two pipes of different widths are filled with water to the same height, each with a balloon at the bottom. How do the balloons bulge?

    1. Equally, because the water columns have the same height
    2. More in the wide pipe, because it holds more water
    3. More in the narrow pipe, because it is thinner
    4. Neither bulges
    Show answer

    Answer: A. Liquid pressure at the bottom depends on the height of the column, not on the width or total weight of water. Equal heights give equal bulges.

  2. 2. Why are overhead water tanks placed at a height?

    1. To keep the water cold.
    2. A taller water column gives more pressure at the taps.
    3. To reduce the pressure at the taps.
    4. So that the water weighs less.
    Show answer

    Answer: B. Pressure increases with the height of water above the tap. Placing the tank high increases that height and gives a strong flow.

  3. 3. Water spurts equally from four holes made at the same height around a bottle. What does this show?

    1. Liquids exert pressure only on the bottom.
    2. Liquids exert pressure on the sides of a container, in all directions.
    3. Water has no pressure at the sides.
    4. The bottle is pushing water out by itself.
    Show answer

    Answer: B. Water flowing out of side holes shows that liquids press on the walls of their container; liquid pressure acts in all directions.

  4. 4. Why is the base of a dam made much broader than its top?

    1. Water pressure is greatest at the surface.
    2. To store more fish.
    3. To make the dam look attractive.
    4. Water pressure is greatest near the bottom, where the water is deepest.
    Show answer

    Answer: D. Pressure increases with depth, so the push on the dam wall is largest at the bottom. A broad base withstands this large pressure.

  5. 5. In a building with a rooftop tank, which tap usually has the weakest flow?

    1. The tap on the ground floor
    2. All taps have exactly equal flow
    3. The tap on the top floor, just below the tank
    4. The tap furthest from the tank
    Show answer

    Answer: C. The top-floor tap has the shortest water column above it, so the pressure there is lowest and the flow weakest.

Sign in to keep track of the lessons you finish.

Next lesson → Air pressure and how winds form

Privacy · Terms · Refunds · Delivery