- Foundation
- About 14 min
- 5 practice questions
Writing and balancing chemical equations
Turn a reaction into a word equation and a symbol equation, then balance it step by step so that atoms are conserved.
If something looks wrong, please tell us.
Describing a reaction in a full sentence every time is slow. Chemists use equations instead: a short way to show what reacts and what forms. An equation is only correct when it is balanced, because atoms are never created or destroyed in a reaction. This lesson shows how to write equations and balance them by a simple, careful method.
From words to symbols
A word equation names the substances: magnesium + oxygen → magnesium oxide. The arrow means 'react to form'. Reactants are written on the left, products on the right, and a plus sign separates substances on the same side. Replacing names with formulas gives a skeletal equation: Mg + O2 → MgO. This is not yet correct, because the left side has two oxygen atoms and the right side has one.
Why equations must balance
The law of conservation of mass says that mass is neither created nor destroyed in a chemical reaction. The total mass of the products equals the total mass of the reactants, because the same atoms are only rearranged. So every kind of atom must appear the same number of times on both sides. We balance an equation by putting whole numbers, called coefficients, in front of formulas. We never change the small numbers inside a formula (the subscripts), because that would change the substance itself: H2O is water, but H2O2 is hydrogen peroxide.
A step-by-step method
- Write the correct formulas of all reactants and products.
- Make a list of each element and count its atoms on each side.
- Start with the formula that has the most atoms, and balance one element at a time.
- Leave elements that appear on their own (like O2, H2 or Fe) until last.
- Recount every element. If all match, the equation is balanced; reduce the coefficients to the smallest whole numbers.
Worked example 1: magnesium burning
Skeletal: Mg + O2 → MgO. Oxygen: 2 on the left, 1 on the right. Put 2 in front of MgO: Mg + O2 → 2MgO. Now magnesium is 1 on the left and 2 on the right, so put 2 in front of Mg: 2Mg + O2 → 2MgO. Check: Mg 2 = 2, O 2 = 2. Balanced.
Worked example 2: methane burning
Skeletal: CH4 + O2 → CO2 + H2O. Carbon is already 1 and 1. Hydrogen: 4 on the left, 2 on the right, so write 2H2O. Now oxygen on the right is 2 (in CO2) + 2 (in 2H2O) = 4, so write 2O2 on the left. CH4 + 2O2 → CO2 + 2H2O. Check: C 1 = 1, H 4 = 4, O 4 = 4.
Worked example 3: iron and steam
Skeletal: Fe + H2O → Fe3O4 + H2. Start with Fe3O4, the formula with the most atoms. Oxygen: 4 on the right, so write 4H2O on the left. Hydrogen is now 8 on the left, so write 4H2 on the right. Iron: 3 on the right, so write 3Fe on the left. 3Fe + 4H2O → Fe3O4 + 4H2. Check: Fe 3 = 3, H 8 = 8, O 4 = 4.
State symbols
Equations often show the physical state of each substance: (s) solid, (l) liquid, (g) gas and (aq) aqueous, meaning dissolved in water. For example, Zn(s) + H2SO4(aq) → ZnSO4(aq) + H2(g). Conditions such as heat, light or a catalyst can be written above or below the arrow.
Balance with coefficients in front of formulas, never by changing subscripts. Count every element on both sides; start with the biggest formula and leave single elements to the end.
Key takeaways
Word equation, then skeletal equation, then balanced equation. Mass is conserved, so atoms must balance. Use the step-by-step method, check your final counts, and add state symbols when they are asked for.
Check your understanding
-
1. What are the coefficients that balance N2 + H2 → NH3?
- 1, 3, 2
- 1, 1, 2
- 2, 3, 2
- 1, 3, 1
Show answer
Answer: A. N: 2 on the left, so 2NH3. Then H on the right is 6, so 3H2. N2 + 3H2 → 2NH3: N 2 = 2, H 6 = 6.
-
2. Balance Al + O2 → Al2O3. What is the coefficient of Al?
- 2
- 3
- 4
- 6
Show answer
Answer: C. O: 2 and 3, the smallest common number is 6, so 3O2 and 2Al2O3. Al on the right is then 4, so 4Al. 4Al + 3O2 → 2Al2O3.
-
3. While balancing an equation, what must you never change?
- The coefficients
- The order of reactants
- The arrow
- The subscripts in a formula
Show answer
Answer: D. Changing a subscript changes the substance (H2O to H2O2, for example). Only coefficients may be changed.
-
4. What does the state symbol (aq) mean?
- A gas
- Dissolved in water
- A pure liquid
- A solid
Show answer
Answer: B. (aq) stands for aqueous: the substance is dissolved in water.
-
5. Balance C3H8 + O2 → CO2 + H2O. What is the coefficient of O2?
- 5
- 3
- 4
- 7
Show answer
Answer: A. C: 3CO2. H: 8 atoms, so 4H2O. O on the right: 3 × 2 + 4 × 1 = 10, so 5O2. C3H8 + 5O2 → 3CO2 + 4H2O.
Sign in to keep track of the lessons you finish.