Revision notes

Chapter 3 Chemical reactions and equations: Foundation

The key points, rules to remember, tables and diagrams from all 5 lessons, on one page for quick revision. To keep a copy, use your browser's Print and choose "Save as PDF".

Lesson 1

Chemical reactions and the rules for writing equations

Two kinds of change

  • Physical change
    • Brought about by changes in temperature, pressure and so on
    • Composition of matter stays the same
    • Often reversible: ice melts on heating and water freezes on cooling
    • Examples: evaporation of water, breaking a glass, naphthalene balls shrinking in air
  • Chemical change
    • Composition of matter changes
    • New substances with new properties are formed
    • Change is usually permanent
    • Examples: cooking food, ripening of fruit, milk turning into curd, digestion of food
Examples of the conventions
ConventionExample
StatesCuSO₄(aq) + Zn(s) → ZnSO₄(aq) + Cu(s)
Heat supplied (Δ) and gas given off (↑)CaCO₃(s) —Δ→ CaO(s) + CO₂↑
Heat given outCuSO₄(aq) + Zn(s) → ZnSO₄(aq) + Cu(s) + Heat
Conditions over the arrowVegetable oil(l) + H₂(g) —Ni catalyst, about 60 °C→ Vanaspati ghee(s)
Precipitate (↓)AgNO₃(aq) + NaCl(aq) → AgCl↓ (white) + NaNO₃(aq)

Key takeaways: a chemical change forms new substances by breaking and forming bonds; a physical change does not alter composition. Reactants go on the left and products on the right of an arrow. States, ↑, ↓, Δ, '+ Heat' and conditions over the arrow make an equation more informative.

Read the full lesson

Lesson 2

Balancing a chemical equation step by step

Law of conservation of mass: in any reaction, the total mass of each element in the reactants equals its total mass in the products. So the number of atoms of each element must be the same on both sides of an equation.

Balancing an equation

  1. Step 1: Write the equation Turn the word equation into formulae.
  2. Step 2: Count the atoms Make a table of each element on the left and the right.
  3. Step 3: Balance one element at a time Start with the compound having the most atoms, and with an element that is unequal. Put a factor in front of a formula.
  4. Step 4: Recheck and write the final equation Count every element again; repeat Step 3 until all are equal.
Atom count before balancing
ElementLeftRight
Ca11
N12
O2 + 3 = 56 + 1 = 7
H2 + 1 = 32

Key takeaways: mass is conserved, so atoms of each element must balance. Count, pick the largest compound, adjust one element at a time with factors, never change formulae, and recheck every element at the end.

Read the full lesson

Lesson 3

Types of reactions: combination, decomposition, displacement and double displacement

Four types of chemical reactions

  • Combination
    • Two or more reactants form a single product
    • A + B → AB
  • Decomposition
    • One reactant gives two or more products
    • AB → A + B
  • Displacement
    • A more reactive element takes the place of a less reactive one
    • A + BC → AC + B
  • Double displacement
    • Ions of two compounds are exchanged, forming a precipitate
    • AB + CD → AD + CB

Key takeaways: combination makes one product; decomposition breaks one reactant, using heat or electricity; in displacement a more reactive element replaces a less reactive one; in double displacement ions are exchanged and a precipitate forms.

Read the full lesson

Lesson 4

Exothermic and endothermic changes, and the rate of a reaction

Heat in physical processes

  • Endothermic processes
    • Melting of ice
    • Dissolving potassium nitrate (KNO₃) in water: the solution becomes colder
  • Exothermic processes
    • Freezing of water into ice
    • Dissolving sodium hydroxide (NaOH) in water: the solution becomes warmer
    • Diluting concentrated sulphuric acid: a very large amount of heat is released

Factors affecting the rate of a reaction

  • Nature of reactants
    • A more reactive substance reacts faster
    • Aluminium reacts faster than zinc with dilute hydrochloric acid
  • Size of particles
    • Smaller particles react faster
    • Powdered limestone fizzes faster in acid than lumps of the same mass
  • Concentration
    • More concentrated reactants react faster
    • Concentrated HCl dissolves calcium carbonate faster than dilute HCl
  • Temperature
    • Higher temperature, faster reaction
    • Limestone does not decompose at room temperature but does on strong heating
  • Catalyst
    • A substance that increases the rate without itself undergoing any chemical change
    • MnO₂ speeds up the decomposition of KClO₃ and of H₂O₂

Key takeaways: endothermic changes absorb heat and exothermic changes release it; this applies to both physical processes and chemical reactions. Add concentrated acid slowly to water, never water to acid. The rate of a reaction increases with more reactive reactants, smaller particles, higher concentration, higher temperature and a catalyst.

Read the full lesson

Lesson 5

Oxidation, reduction, redox, corrosion and rancidity

Oxidation: gain of oxygen, loss of hydrogen, loss of electrons. Reduction: loss of oxygen, gain of hydrogen, gain of electrons. Both happen together: Redox = Reduction + Oxidation.

How rust forms (an electrochemical process)

  1. Anode region: iron is oxidised Fe(s) → Fe²⁺(aq) + 2e⁻
  2. Cathode region: oxygen is reduced O₂(g) + 4H⁺(aq) + 4e⁻ → 2H₂O(l)
  3. Fe²⁺ moves and is oxidised further It reacts with water and oxygen to form Fe³⁺ ions.
  4. Rust collects on the surface Fe³⁺ forms reddish hydrated iron(III) oxide, Fe₂O₃·xH₂O.
Different regions of the same iron surface act as anode and cathode.

Key takeaways: oxidation is gain of oxygen, loss of hydrogen or loss of electrons; reduction is the opposite, and the two always occur together as redox. The oxidant is reduced and the reductant is oxidised. Rusting needs air and water and is an electrochemical redox process. Rancidity is air oxidation of fats and oils.

Read the full lesson

Privacy · Terms · Refunds · Delivery