- Practice
- About 18 min
- 5 practice questions
Metallurgy: ores, concentration and extraction of reactive metals
Define metallurgy, mineral, ore and gangue, describe gravity, magnetic, froth flotation and leaching methods of concentration, and explain extraction of sodium and aluminium by electrolysis.
If something looks wrong, please tell us.
By the end of this lesson you can
- Define metallurgy, minerals, ores and gangue.
- Describe four methods of concentrating ores and say which ores they suit.
- Explain how reactive metals such as sodium and aluminium are obtained by electrolytic reduction.
Metallurgy is the science and technology of extracting metals from their ores and purifying them for use. Most metals are reactive, so in nature they occur in the combined state as oxides, carbonates, sulphides, nitrates and so on. The least reactive metals, such as silver, gold and platinum, which are not affected by air and water, generally occur in the free state.
Minerals, ores and gangue
- Minerals: compounds of metals that occur naturally, along with impurities.
- Ores: minerals from which the metal can be extracted economically. Every ore is a mineral, but not every mineral is an ore.
- Gangue: the impurities in an ore, such as soil, sand and rocky material.
Main stages of metallurgy
- Concentration of the ore Remove gangue to increase the proportion of the metal compound.
- Extraction of the metal Reduce the metal compound to metal; the method depends on the metal's reactivity.
- Refining Purify the impure metal, usually by electrolysis.
Concentration of ores
The method chosen depends on the physical properties of the ore and gangue, the reactivity of the metal, the facilities available and possible pollution.
- Separation based on gravitation: heavier ore particles are separated from lighter gangue using water. On a Wilfley table, a sloping vibrating table with thin wooden riffles, water washes light gangue away while heavy ore particles collect between the riffles. In hydraulic separation, finely ground ore is put in a tapering tank with a strong jet of water from below; light gangue is carried out at the top and heavy ore particles settle at the bottom.
- Magnetic separation: powdered ore falls on a conveyor belt moving over a magnetic roller. Magnetic particles stick to the roller and drop close to it; non-magnetic particles fall farther away. In cassiterite (a tin ore), non-magnetic tin oxide (SnO₂) is separated from magnetic ferrous tungstate (FeWO₄) this way.
- Froth flotation: used for sulphide ores such as zinc blende (ZnS) and copper pyrites (CuFeS₂). Finely ground ore is put in water with a little pine or eucalyptus oil, and air is blown through while an agitator stirs. Sulphide particles are hydrophobic and get wetted by the oil; they rise with the froth. Gangue particles are hydrophilic, get wetted by water and sink.
- Leaching: the ore is soaked for a long time in a solution that dissolves the metal compound by a chemical reaction but not the gangue. It is the first step for aluminium, gold and silver; bauxite is leached with aqueous NaOH or Na₂CO₃.
Extraction of highly reactive metals
Metals at the top of the reactivity series hold on to oxygen and chlorine very strongly, so carbon cannot reduce their compounds. They are obtained by electrolytic reduction. Sodium, calcium and magnesium are obtained by electrolysis of their molten chlorides: the metal is deposited at the cathode and chlorine is released at the anode.
Electrolysis of molten NaCl. Cathode: Na⁺ + e⁻ → Na (reduction). Anode: 2Cl⁻ → Cl₂ + 2e⁻ (oxidation).
Extraction of aluminium
Aluminium (Al, atomic number 13, configuration 2,8,3, valency 3) is the third most abundant element in the earth's crust, after oxygen and silicon, but being reactive it never occurs free. Its main ore is bauxite, Al₂O₃·nH₂O, which contains impurities such as silica (SiO₂), ferric oxide (Fe₂O₃) and titanium oxide (TiO₂).
Step 1, concentration by leaching. In Bayer's process, ground bauxite is heated with concentrated caustic soda under pressure. Aluminium oxide is amphoteric, so it dissolves to form sodium aluminate: Al₂O₃·2H₂O + 2NaOH → 2NaAlO₂ + 3H₂O. Iron oxide does not dissolve and is filtered off. Diluting and cooling the solution precipitates aluminium hydroxide: NaAlO₂ + 2H₂O → NaOH + Al(OH)₃. In Hall's process, bauxite is leached with aqueous sodium carbonate: Al₂O₃·2H₂O + Na₂CO₃ → 2NaAlO₂ + CO₂ + 2H₂O; then carbon dioxide is passed in to precipitate the hydroxide: 2NaAlO₂ + 3H₂O + CO₂ → 2Al(OH)₃ + Na₂CO₃. In both, the hydroxide is heated strongly (calcined, about 1000 °C) to get pure alumina: 2Al(OH)₃ → Al₂O₃ + 3H₂O.
Step 2, electrolytic reduction. Alumina melts above 2000 °C, so cryolite (Na₃AlF₆) and fluorspar (CaF₂) are added to lower the melting point to about 1000 °C. The molten mixture is electrolysed in a steel tank lined with graphite, which acts as the cathode; graphite rods dipping in the melt are the anodes. Cathode: Al³⁺ + 3e⁻ → Al. Anode: 2O²⁻ → O₂ + 4e⁻. Molten aluminium, heavier than the electrolyte, collects at the bottom and is tapped off. The oxygen reacts with the graphite anodes to form carbon dioxide, so the anodes burn away and must be replaced from time to time.
Key takeaways: ores are minerals from which metals can be extracted economically; gangue is the impurity. Ores are concentrated by gravity, magnetic, froth flotation or leaching methods. Highly reactive metals are extracted by electrolysis of their molten compounds; aluminium comes from bauxite by leaching (Bayer's or Hall's process) followed by electrolysis of alumina with cryolite.
Check your understanding
-
1. The impurities such as sand and soil present in an ore are called:
- Minerals
- Gangue
- Alloys
- Flux
Show answer
Answer: B. Gangue is the unwanted earthy and rocky material present along with the metal compound in an ore.
-
2. Which method is used to concentrate sulphide ores such as zinc blende?
- Froth flotation
- Magnetic separation
- Leaching with NaOH
- Hydraulic separation only
Show answer
Answer: A. Sulphide particles are wetted by oil and rise with the froth, while gangue is wetted by water and sinks. This is froth flotation.
-
3. In the extraction of aluminium, why is cryolite added to alumina?
- To make aluminium magnetic
- To act as the cathode
- To remove iron oxide
- To lower the melting point of the mixture to about 1000 °C
Show answer
Answer: D. Alumina melts above 2000 °C. Cryolite and fluorspar lower the melting point of the mixture to about 1000 °C, saving energy.
-
4. Why do the graphite anodes have to be replaced during the electrolysis of alumina?
- Aluminium deposits on them
- They melt
- Oxygen released at the anode reacts with the carbon to form carbon dioxide
- They become magnetic
Show answer
Answer: C. Oxygen formed at the anode combines with the graphite (carbon), so the anodes slowly burn away as CO₂.
-
5. In the electrolysis of molten sodium chloride, what is formed at the cathode?
- Sodium metal
- Chlorine gas
- Hydrogen gas
- Oxygen gas
Show answer
Answer: A. At the cathode Na⁺ ions gain electrons: Na⁺ + e⁻ → Na. Chlorine gas is released at the anode.
Sign in to keep track of the lessons you finish.