• Practice
  • About 15 min
  • 5 practice questions

Diode, Zener and transistor numericals

Solve simple diode circuits, a Zener regulator and transistor current and gain problems, using the fixed relations between the currents.

If something looks wrong, please tell us.

Electronics questions in physics exams are short and numerical. They ask for a current in a diode circuit, the currents in a Zener voltage regulator, or the gain of a transistor stage. Each uses only Ohm's law and a few fixed relations. This lesson sets out the method for each.

Diode circuits

A silicon diode in forward bias drops about 0.7 V across itself, and the rest of the supply voltage appears across the resistor. In reverse bias, it passes almost no current. For an ideal diode, the forward drop is taken as zero. In a half-wave rectifier, the output frequency equals the input frequency; in a full-wave rectifier it is twice the input frequency.

Worked example 1: a silicon diode

The values are for practice. A 5 V supply is connected through a silicon diode (0.7 V drop) in series with a 1 kΩ resistor. I = (5 − 0.7)/1000 = 4.3 mA. With two such diodes in series, the drop is 1.4 V and I = (5 − 1.4)/1000 = 3.6 mA. With the diode reversed, I ≈ 0.

The Zener regulator

A Zener diode is used in reverse bias. Once the voltage reaches the Zener value V_Z, it holds the voltage almost constant while the current changes. In a regulator, a series resistor R_s carries the total current, which divides between the Zener and the load: I_s = (V_in − V_Z)/R_s and I_s = I_Z + I_L.

Worked example 2: a regulator

A 12 V supply feeds a 6 V Zener through R_s = 300 Ω, with a load of 600 Ω across the Zener. Total current: I_s = (12 − 6)/300 = 20 mA. Load current: I_L = 6/600 = 10 mA. Zener current: I_Z = 20 − 10 = 10 mA. If the load is removed, the Zener takes all 20 mA, and the power in it is 6 × 0.02 = 0.12 W. The output stays at 6 V.

The transistor

  • In a transistor, the emitter current is the sum of the base and collector currents: I_E = I_B + I_C.
  • Current gain in the common-emitter circuit: β = I_C/I_B. In the common-base circuit: α = I_C/I_E. They are related by α = β/(1 + β) and β = α/(1 − α).
  • Voltage gain of a common-emitter amplifier: A_v = β R_L/R_in, where R_in is the input resistance and R_L the load resistance. Power gain = β × A_v.
  • As a switch, a transistor with no base current is off (cut off), and with enough base current it is on (saturated).

Worked example 3: transistor currents

A transistor has a base current of 40 µA and β = 100. I_C = β I_B = 100 × 40 µA = 4 mA. I_E = I_B + I_C = 0.04 + 4 = 4.04 mA. α = I_C/I_E = 4/4.04 ≈ 0.99, and the check α = β/(1 + β) = 100/101 ≈ 0.99 agrees.

Worked example 4: amplifier gain

With β = 100, R_L = 5 kΩ and R_in = 1 kΩ, the voltage gain is A_v = 100 × 5000/1000 = 500, and the power gain is 100 × 500 = 5 × 10⁴. A small input voltage of 2 mV would be raised to 500 × 2 mV = 1 V at the output.

I_E = I_B + I_C. β = I_C/I_B. α = β/(1 + β). A_v = βR_L/R_in. Zener: I_s = I_Z + I_L.

— Relations to remember

Key takeaways

Work from the known resistor: find the current there, then split it. In a transistor, remember that the base current is tiny, so α is slightly less than 1 and β is large.

Check your understanding

  1. 1. A 3 V supply is connected to an ideal forward-biased diode in series with a 100 Ω resistor. The current is:

    1. 30 mA
    2. 3 mA
    3. 0.3 A
    4. 0.03 mA
    Show answer

    Answer: A. I = V/R = 3/100 = 0.03 A = 30 mA.

  2. 2. A transistor has I_B = 20 µA and β = 50. The collector current is:

    1. 2.5 mA
    2. 0.4 mA
    3. 1 mA
    4. 70 mA
    Show answer

    Answer: C. I_C = βI_B = 50 × 20 µA = 1000 µA = 1 mA.

  3. 3. A transistor has α = 0.98. The value of β is:

    1. 49
    2. 98
    3. 0.02
    4. 4.9
    Show answer

    Answer: A. β = α/(1 − α) = 0.98/0.02 = 49.

  4. 4. In a Zener regulator, the current in the series resistor is 15 mA and the load takes 9 mA. The Zener current is:

    1. 24 mA
    2. 6 mA
    3. 135 mA
    4. 1.7 mA
    Show answer

    Answer: B. I_Z = I_s − I_L = 15 − 9 = 6 mA.

  5. 5. A full-wave rectifier is connected to a 50 Hz supply. The frequency of the pulsating output is:

    1. 25 Hz
    2. 50 Hz
    3. 200 Hz
    4. 100 Hz
    Show answer

    Answer: D. A full-wave rectifier produces two pulses per cycle, so the output frequency is 2 × 50 = 100 Hz.

Privacy · Terms · Refunds · Delivery