Revision notes

Chapter 11 Sound: Foundation

The key points, rules to remember, tables and diagrams from all 5 lessons, on one page for quick revision. To keep a copy, use your browser's Print and choose "Save as PDF".

Lesson 1

How sound is produced and how it travels

What vibrates to make the sound
Source of soundPart that vibratesHow it is set vibrating
Human voiceVocal cordsAir from the lungs
Sitar or guitarStretched stringsPlucking
FluteAir column inside the tubeBlowing
Dholak or tablaStretched skin (membrane)Striking
Buzzing beeWingsRapid flapping
Plucked rubber bandThe band itselfPlucking

One vibration of a source in air

  1. Source moves forward Air in front is squeezed: compression (high pressure)
  2. Source moves back Air thins out: rarefaction (low pressure)
  3. Source moves forward again A new compression follows the first one outwards

Then back to step 1: Source moves forward

Sound = vibrations passed from particle to particle as compressions (high pressure) and rarefactions (low pressure). The particles stay; the disturbance travels.

Key takeaways: sound is produced by vibrating objects and is a form of energy. It needs a medium (solid, liquid or gas) and cannot pass through a vacuum. The particles of the medium only vibrate about their places, passing on compressions and rarefactions, so sound is a mechanical wave.

Read the full lesson

Lesson 2

Longitudinal waves and the measures of a sound wave

Two kinds of wave

  • Longitudinal wave
    • Particles vibrate along the direction of travel
    • Forms compressions and rarefactions
    • Example: sound in air, pulses on a slinky
  • Transverse wave
    • Particles vibrate at right angles to the direction of travel
    • Forms crests and troughs
    • Example: ripples on water; light (not mechanical)
Measures of a sound wave
QuantityMeaningSymbolSI unit
WavelengthDistance between two consecutive compressions (or two consecutive rarefactions)λ (lambda)metre (m)
FrequencyNumber of complete oscillations (of density or pressure) per unit timeν (nu)hertz (Hz)
Time periodTime for one complete oscillation, or for two consecutive compressions to pass a pointTsecond (s)
AmplitudeSize of the maximum disturbance on either side of the mean valueAUnit of density or pressure

ν = 1/T and T = 1/ν. A higher frequency means a shorter time period.

Key takeaways: sound waves are longitudinal: particles vibrate along the direction of travel, forming compressions and rarefactions. Transverse waves vibrate at right angles to the direction of travel. A sound wave is described by wavelength λ (m), frequency ν (Hz), time period T (s) and amplitude A, with ν = 1/T.

Read the full lesson

Lesson 3

Pitch, loudness, quality and the speed of sound

Characteristics of sound

  • Pitch
    • Depends on frequency
    • Faster vibration = higher pitch
  • Loudness
    • Depends on amplitude
    • Harder vibration = louder
  • Quality (timbre)
    • Depends on the mix of frequencies
    • Tells a flute from a violin at the same pitch

Speed = wavelength × frequency: v = λ ν. Also v = distance ÷ time.

A few speeds from the textbook's table (at 25 °C); you need not memorise them
StateMediumSpeed (m s⁻¹)
SolidAluminium6420
SolidIron5950
LiquidWater (distilled)1498
GasAir346

Key takeaways: pitch follows frequency, loudness follows amplitude, and quality follows the mixture of frequencies. Loudness is the ear's response to intensity. For any wave, v = λν. Sound is fastest in solids and slowest in gases, and speeds up as temperature rises.

Read the full lesson

Lesson 4

Reflection of sound, echo and reverberation

Echo: sound goes to the obstacle and back, so distance of obstacle d = (speed × time) ÷ 2. For a distinct echo, time ≥ 0.1 s.

Solving an echo problem

  1. Note the speed v and the echo time t
  2. Total path = v × t Sound goes to the obstacle and comes back
  3. Distance of obstacle = v × t ÷ 2
Putting reflection of sound to use
Device or designHow reflection helps
Megaphone, horn, trumpet, shehnaiA tube with a conical opening reflects sound again and again, sending most of it forward towards the listeners instead of in all directions
StethoscopeSounds of the heart or lungs travel along the tubes to the doctor's ears by multiple reflection
Curved ceiling of a hallReflected sound is spread to all corners of the hall
Curved soundboard behind the stageReflects the speaker's sound evenly across the width of the hall

Key takeaways: sound obeys the same laws of reflection as light. An echo needs a gap of at least 0.1 s, which in air at about 344 m s⁻¹ means an obstacle at least 17.2 m away; obstacle distance = v × t ÷ 2. Reverberation is persistence of sound by repeated reflection and is reduced with absorbing materials. Megaphones, stethoscopes, curved ceilings and soundboards all use multiple reflection.

Read the full lesson

Lesson 5

Range of hearing, infrasound and uses of ultrasound

The frequency scale of sound

  1. Infrasound Below 20 Hz
  2. Audible sound About 20 Hz to 20 kHz
  3. Ultrasound Above 20 kHz

How a hearing aid works

  1. Microphone Changes sound waves into electrical signals
  2. Amplifier Makes the electrical signals stronger
  3. Speaker Changes the amplified signals back into sound
  4. Ear Receives the louder sound
Uses of ultrasound described in the chapter
UseHow it works
CleaningObjects with hard-to-reach parts (spiral tubes, odd-shaped parts, electronic components) are put in a cleaning solution; ultrasound sent into it shakes loose dust, grease and dirt
Finding flaws in metalUltrasound is passed through metal blocks used in buildings, bridges and machines; a crack or flaw reflects it back, revealing the defect
EchocardiographyUltrasound reflected from different parts of the heart forms an image of the heart
UltrasonographyAn ultrasound scanner images organs such as the liver, gall bladder, kidney and uterus, helping doctors find stones or tumours; it is also used to examine the foetus during pregnancy

Audible: 20 Hz to 20 kHz. Below 20 Hz: infrasound. Above 20 kHz: ultrasound, which travels in well-defined paths and is used for cleaning, flaw detection and medical imaging.

Key takeaways: humans hear roughly 20 Hz to 20 kHz. Infrasound lies below this and ultrasound above it. A hearing aid turns sound into electrical signals, amplifies them and turns them back into sound. Ultrasound's short wavelength lets it be aimed precisely, so it is used to clean parts, detect hidden flaws and image organs of the body.

Read the full lesson

Privacy · Terms · Refunds · Delivery