• Foundation
  • About 15 min
  • 5 practice questions

How a nuclear power reactor works: fuel, moderator, control rods and coolant

Name the main parts of a nuclear reactor and what each does, compare the common moderators and control-rod materials, and recognise the main reactor types.

If something looks wrong, please tell us.

A nuclear power station is, at heart, a steam power station. Like a coal plant, it boils water, the steam spins a turbine and the turbine turns a generator. The only difference is the source of heat: a controlled fission chain reaction in the reactor core instead of burning coal. Exams ask what each part of the reactor does and which material is used for which job.

The parts of a reactor

What each part of a reactor does
PartJobCommon materials
FuelUndergoes fission and gives heatUranium (natural or enriched), plutonium; usually as oxide pellets in metal tubes
ModeratorSlows fast neutrons so they can split uranium-235 easilyHeavy water, ordinary (light) water, graphite
Control rodsAbsorb neutrons to slow down or stop the chain reactionBoron, cadmium
CoolantCarries heat away from the coreHeavy water, light water, liquid sodium, carbon dioxide gas
Shielding and containmentKeep radiation and radioactive material inThick concrete and steel

Why neutrons need slowing down

Neutrons come out of fission very fast. Uranium-235 captures slow (thermal) neutrons far more readily than fast ones. A moderator slows them by letting them bump into light nuclei, losing a little speed at each collision, rather like a ball bouncing off other balls. A good moderator slows neutrons without swallowing them. Heavy water (D₂O, water made with deuterium) absorbs very few neutrons, so a reactor using it can run on natural uranium. Ordinary water absorbs more, so such reactors need uranium enriched to a few per cent uranium-235. Graphite (a form of carbon) is also used.

Do not mix up moderator and control rods: the moderator slows neutrons, which helps fission; control rods absorb neutrons, which reduces fission. Pushing control rods deeper into the core slows the reaction; pulling them out speeds it up. Dropping them fully in shuts the reactor down.

From heat to electricity

  1. Fission in the fuel heats the core.
  2. The coolant carries heat to a steam generator (or the water boils directly in the core).
  3. Steam spins a turbine, which turns a generator to make electricity.
  4. The steam is cooled back into water in a condenser - which is why nuclear stations are built beside rivers, lakes or the sea - and the water is pumped back.

Main reactor types

Reactor types you should know
TypeFuelModeratorCoolant
Pressurised Heavy Water Reactor (PHWR)Natural uraniumHeavy waterHeavy water
Boiling Water Reactor (BWR)Enriched uraniumLight waterLight water, boiling in the core
Pressurised Water Reactor (PWR)Enriched uraniumLight waterLight water kept under pressure so it does not boil
Fast Breeder Reactor (FBR)Plutonium with uraniumNone - uses fast neutronsLiquid sodium

A breeder reactor makes more fissile fuel than it uses: fast neutrons turn the plentiful but non-splitting uranium-238 into plutonium-239, which can then be used as fuel. The PHWR is the workhorse of India's nuclear power programme.

Worked example 1: which reactor?

A reactor uses natural uranium as fuel. Which moderator must it use, heavy water or light water? Working: natural uranium has only about 0.7 per cent uranium-235, so very few neutrons can be wasted. Light water absorbs too many neutrons to sustain a chain reaction with natural uranium. Heavy water absorbs very few, so the answer is heavy water - this is the PHWR.

Worked example 2: efficiency

Suppose a reactor produces 3,000 megawatts of heat and the station sends out 1,000 megawatts of electricity. What is its efficiency? Working: efficiency = output ÷ input × 100 = 1,000 ÷ 3,000 × 100 = about 33 per cent. The other two-thirds of the heat goes to the condenser cooling water. (Figures are illustrative.)

Moderator slows neutrons (heavy water, light water, graphite). Control rods absorb neutrons (boron, cadmium). Coolant carries heat away. Natural uranium needs heavy water.

Key takeaways: a reactor is a heat source for a steam turbine. Fuel splits, the moderator slows neutrons, control rods absorb them and the coolant removes heat. PHWRs run on natural uranium with heavy water; BWRs and PWRs use enriched uranium with light water; fast breeders need no moderator and use liquid sodium.

Check your understanding

  1. 1. In a nuclear reactor, the function of the moderator is to:

    1. Absorb all the neutrons and stop the reaction
    2. Slow down fast neutrons so they can cause fission
    3. Carry heat from the core to the turbine
    4. Stop radiation from leaving the building
    Show answer

    Answer: B. The moderator slows fast neutrons to thermal speeds, at which uranium-235 captures them easily. Absorbing neutrons is the job of control rods; carrying heat is the coolant's job.

  2. 2. Which of these materials is used in control rods?

    1. Graphite
    2. Heavy water
    3. Liquid sodium
    4. Cadmium
    Show answer

    Answer: D. Cadmium and boron absorb neutrons strongly, so they are used in control rods. Graphite and heavy water are moderators; liquid sodium is a coolant.

  3. 3. A reactor that runs on natural uranium uses which moderator?

    1. Heavy water
    2. Light water
    3. Liquid sodium
    4. Boron
    Show answer

    Answer: A. Heavy water absorbs very few neutrons, so the small share of uranium-235 in natural uranium can still sustain a chain reaction. Light-water reactors need enriched uranium; sodium is a coolant and boron an absorber.

  4. 4. Which type of reactor uses no moderator?

    1. Pressurised Heavy Water Reactor
    2. Boiling Water Reactor
    3. Fast Breeder Reactor
    4. Pressurised Water Reactor
    Show answer

    Answer: C. A fast breeder reactor runs on fast neutrons, so it deliberately has no moderator. It is cooled by liquid sodium.

  5. 5. To shut down a nuclear reactor quickly, operators:

    1. Pull the control rods out of the core
    2. Drop the control rods fully into the core
    3. Add more fuel to the core
    4. Remove the moderator and add more fuel
    Show answer

    Answer: B. Fully inserted control rods absorb so many neutrons that the chain reaction stops. Pulling them out would increase the reaction.

Privacy · Terms · Refunds · Delivery