• Practice
  • About 16 min
  • 5 practice questions

Folds, faults, rift valleys and block mountains

Name the parts and types of folds, explain how fold mountains form, and describe normal, reverse and strike-slip faults with the rift valleys and horsts they create.

If something looks wrong, please tell us.

By the end of this lesson you can

  • Label the parts of a fold and describe five types of fold.
  • Describe the parts of a fault and the three main types of fault.
  • Explain the formation of rift valleys (graben) and block mountains (horst) with examples.

Rock layers are laid down flat, yet in a road cutting through hills you often see them bent into arches or broken and shifted. Squeezing makes rocks bend; pulling or shearing makes them break. These two responses, folding and faulting, build many of the world's great landforms.

Folds

Horizontal earth movements produce compression and tension. Folding is the bending of rock strata by compression; folding on a large scale builds mountains (orogeny).

  • Anticline: the upfolded arch of a fold.
  • Syncline: the downfolded trough.
  • Limb: the side of a fold.
  • Crest: the top of the fold.
  • Axial plane (axis): the plane that bisects the angle between the two limbs.
Five types of fold
TypeHow it formsShape
Symmetrical (open)Equal compression from both sidesBoth limbs dip at the same angle
AsymmetricalStronger compression from one sideOne limb steeper than the other
IsoclinalIntense compressionBoth limbs at the same angle and parallel to each other
OverturnedOne limb pushed over the otherBoth limbs dip the same way
RecumbentVery strong one-sided pushThe fold lies almost flat on its side

When plates converge, weak rocks and sediments between them are squeezed into long parallel folds, forming fold mountain ranges such as the Himalaya, Alps, Andes, Rockies and Atlas. Anticline tops tend to become peaks and synclines valleys. High intermontane plateaus, surrounded by ranges on all sides, can lie between them; Tibet is the textbook's example.

Faults

A fault is a break in the crust along which blocks of rock have moved past each other. Faults usually occur along plate boundaries, where plate motion compresses, pulls or shears the crust, and sudden slip on active faults causes most earthquakes. Parts of a fault: the fault plane (surface of movement), the fault dip (angle between the fault plane and the horizontal), the hanging wall (block above the fault plane), the footwall (block below it), the upthrown and downthrown sides, and the fault scarp, a steep, sometimes cliff-like slope produced by faulting.

Three main types of fault

  • Normal fault
    • Caused by tension where crust is pulled apart
    • Hanging wall moves down relative to the footwall
    • Forms rift valleys and horsts
  • Reverse fault
    • Caused by compression where crust is pushed together
    • Hanging wall moves up over the footwall
    • Common at convergent boundaries
  • Strike-slip (transform) fault
    • Caused by shearing
    • Blocks slide sideways past each other with little up-down movement
    • Common at transform boundaries and offsets of mid-ocean ridges

Rift valleys and block mountains

A rift valley or graben (German for 'trough') forms when a narrow block drops between two parallel normal faults. It is usually long, narrow and deep, and may fill with water or carry a river. Examples: the Rhine rift valley, flanked by the Vosges and the Black Forest; the rift of the Narmada, which the textbook places between the Vindhya and Satpura ranges; and the Great Rift Valley of Africa, the longest in the world, which the textbook describes as about 6,400 km long from Mozambique to Syria, with lakes such as Tanganyika along it and the Red Sea and Dead Sea forming parts of it.

A block mountain or horst forms when a block between two faults is pushed up, or the blocks on either side sink, so that the central mass stands high. The Vosges and Black Forest are block mountains; the textbook also describes the Vindhya and Satpura ranges of central-western India as block mountains.

Compression bends rock into folds or pushes it up in reverse faults; tension breaks it in normal faults; shearing moves it sideways in strike-slip faults. Graben sinks, horst stands.

Worked example 1: reading a cross-section

A geologist sees a block of rock that has slid down along an inclined fault, away from the block beside it. Step 1: the block above the fault plane is the hanging wall. Step 2: it has moved down relative to the footwall. Step 3: downward movement of the hanging wall means the crust was being pulled apart. Answer: a normal fault caused by tension.

Worked example 2: graben or horst?

Between two parallel faults, a central block stands about 500 m above the land on either side (made-up figure), with steep fault scarps on both edges. Reasoning: a raised central block bounded by faults is a horst. If the central block had dropped instead, with the sides standing high, it would be a graben (rift valley).

Key takeaways: folds have anticlines, synclines, limbs, a crest and an axial plane, and may be symmetrical, asymmetrical, isoclinal, overturned or recumbent; faults are normal (tension), reverse (compression) or strike-slip (shear); graben are rift valleys and horsts are block mountains.

Check your understanding

  1. 1. The downfolded trough of a fold is called the:

    1. anticline
    2. crest
    3. syncline
    4. limb
    Show answer

    Answer: C. A syncline is the down-arched part; the anticline is the up-arched part and the crest is its top.

  2. 2. A fold in which one limb is steeper than the other is:

    1. asymmetrical
    2. symmetrical
    3. isoclinal
    4. recumbent
    Show answer

    Answer: A. Stronger compression from one side makes one limb steeper, giving an asymmetrical fold.

  3. 3. A rift valley is formed by:

    1. a block rising between two reverse faults
    2. folding of soft sediments
    3. sideways movement along a strike-slip fault
    4. a block sinking between two parallel normal faults
    Show answer

    Answer: D. Tension creates parallel normal faults and the block between them drops, forming a graben or rift valley.

  4. 4. In a reverse fault, the hanging wall:

    1. moves down relative to the footwall
    2. moves up relative to the footwall
    3. moves only sideways
    4. does not move
    Show answer

    Answer: B. Compression pushes the hanging wall up over the footwall in a reverse fault; in a normal fault it moves down.

  5. 5. The Black Forest and the Vosges, on either side of the Rhine rift, are examples of:

    1. fold mountains
    2. volcanic cones
    3. block mountains
    4. residual hills
    Show answer

    Answer: C. They stand as uplifted blocks (horsts) beside the downfaulted Rhine rift valley.

Sign in to keep track of the lessons you finish.

Next lesson → Earthquakes and volcanoes

Privacy · Terms · Refunds · Delivery