- Foundation
- About 20 min
- 5 practice questions
Calculating with significant figures, rounding off and uncertainty
Apply the multiplication-division and addition-subtraction rules for significant figures, round off by the standard convention, and combine the uncertainties of measured values.
If something looks wrong, please tell us.
By the end of this lesson you can
- Give the result of a product or quotient to the least number of significant figures.
- Give the result of a sum or difference to the least number of decimal places.
- Round off correctly, including the special rule when the dropped digit is exactly 5.
- Express an uncertainty as absolute, relative and percentage error, and combine errors in a product.
A calculation cannot make a measurement more precise than it was. If you divide a mass measured to four significant figures by a volume measured to three, your calculator may display eleven digits, but at most three of them mean anything. The rules below make sure the answer carries the same precision as the data it came from.
Rule 1: multiplication and division
In multiplication or division, keep in the result as many significant figures as the input value with the fewest significant figures. For example, a rectangular plot measures 12.4 m by 3.6 m. The product is 44.64 m², but 3.6 has only two significant figures, so the area is reported as 45 m².
Rule 2: addition and subtraction
In addition or subtraction, keep in the result as many decimal places as the input with the fewest decimal places. Here the count of significant figures is not what matters; the position of the last reliable digit is. Adding masses 12.35 g + 4.1 g + 0.068 g gives 16.518 g by arithmetic, but 4.1 g is reliable only to the first decimal place, so the sum is 16.5 g.
Subtraction can reduce the number of significant figures sharply. Two lengths 5.62 cm and 5.48 cm each have three significant figures, yet their difference 0.14 cm has only two. Similarly 15.8 g − 9.43 g = 6.37 g by arithmetic, which must be reported as 6.4 g because 15.8 is known only to one decimal place.
Which rule applies?
-
Multiply or divide
- Look at the number of significant figures in each input
- Result keeps the smallest count
- Example: 12.4 × 3.6 = 44.64 → 45
-
Add or subtract
- Look at the number of decimal places in each input
- Result keeps the fewest decimal places
- Example: 12.35 + 4.1 + 0.068 = 16.518 → 16.5
Rounding off
To round a value to a chosen number of significant figures, look at the first digit to be dropped. If it is more than 5, raise the preceding digit by 1 (6.487 → 6.49). If it is less than 5, leave the preceding digit as it is (6.483 → 6.48). If the dropped digit is exactly 5, the convention is: leave the preceding digit unchanged if it is even, and raise it by 1 if it is odd. So 4.365 rounds to 4.36 (6 is even) but 4.375 rounds to 4.38 (7 is odd). Over many roundings this convention avoids always pushing results upward.
In a long, multi-step calculation, keep one digit more than the final precision in intermediate steps, and round only at the end. Otherwise rounding errors build up. For example, 1/7.36 = 0.13587. Rounded to three figures that is 0.136, and 1/0.136 = 7.35, not the 7.36 we began with. Keeping one extra digit, 1/0.1359 = 7.358, which rounds back to 7.36. Exact numbers and constants known very precisely, such as π, are given enough digits not to limit the result (3.142 or 3.14 as needed).
× or ÷: fewest significant figures. + or −: fewest decimal places. Dropped digit exactly 5: preceding even digit stays, odd digit goes up.
Uncertainty: absolute, relative and percentage error
A metre scale with millimetre marks reads a length such as 20.4 cm with an uncertainty of about ±0.1 cm. This ±0.1 cm is the absolute error Δl. The relative error is Δl/l, and multiplied by 100 it becomes the percentage error. The same absolute error matters more for a small reading: ±0.01 g on 2.05 g is (0.01/2.05) × 100 ≈ 0.5%, while ±0.01 g on 8.75 g is only about 0.1%.
When measured values are combined, their errors combine too. For a sum or difference Z = A ± B, the absolute errors add: ΔZ = ΔA + ΔB. For a product or quotient Z = AB or Z = A/B, the relative errors add: ΔZ/Z = ΔA/A + ΔB/B. For a power Z = Aⁿ, the relative error is multiplied by the power: ΔZ/Z = n(ΔA/A). These are the maximum possible errors, since the separate errors could in the worst case all act in the same direction.
Worked example 1: area of a sheet with its uncertainty
A sheet measures l = 20.4 ± 0.1 cm and b = 10.2 ± 0.1 cm. Find its area with the uncertainty. Step 1: area = 20.4 × 10.2 = 208.08 cm². Step 2: relative errors: 0.1/20.4 ≈ 0.0049 (0.49%) and 0.1/10.2 ≈ 0.0098 (0.98%). Step 3: for a product they add: 0.49% + 0.98% ≈ 1.47%. Step 4: absolute error in area = 1.47% of 208.08 ≈ 3.06 cm², about 3 cm². Answer: area = 208 ± 3 cm². The area is quoted to three significant figures, matching the data.
Worked example 2: density to the right precision
A metal block has mass 39.25 g and volume 5.0 cm³. Find its density. Step 1: ρ = m/V = 39.25 g / 5.0 cm³ = 7.85 g cm⁻³ by arithmetic. Step 2: the mass has four significant figures and the volume only two, so the quotient keeps two. Step 3: round 7.85 to two figures: the dropped digit is exactly 5 and the preceding digit 8 is even, so it stays. Answer: ρ = 7.8 g cm⁻³.
Worked example 3: error in a squared quantity
The radius of a wire is measured with a 2% error. What is the percentage error in its cross-sectional area A = πr²? π is an exact constant (no error) and the power of r is 2, so ΔA/A = 2 × (Δr/r) = 2 × 2% = 4%. Answer: 4%.
Key takeaways
- The result of a calculation is never more precise than its least precise input.
- Products and quotients follow significant figures; sums and differences follow decimal places.
- Keep one extra digit in intermediate steps and round once at the end.
- Relative errors add in products and quotients; a power multiplies the relative error.
Check your understanding
-
1. The sides of a rectangle are measured as 6.25 m and 2.1 m. The area, to correct significant figures, is:
- 13.125 m²
- 13 m²
- 13.1 m²
- 13.13 m²
Show answer
Answer: B. 6.25 × 2.1 = 13.125 m². In multiplication, keep the fewest significant figures among the inputs: 2.1 has two. Rounded to two significant figures, 13.125 becomes 13 m².
-
2. What is 8.326 g + 2.41 g + 120.5 g reported to correct precision?
- 131.236 g
- 131.24 g
- 131.2 g
- 131 g
Show answer
Answer: C. Arithmetic sum: 8.326 + 2.41 + 120.5 = 131.236 g. In addition keep the fewest decimal places among the inputs: 120.5 has one. So the sum is 131.2 g.
-
3. Rounded to three significant figures, 3.845 becomes:
- 3.84
- 3.85
- 3.80
- 3.9
Show answer
Answer: A. The digit to be dropped is exactly 5 and the preceding digit 4 is even, so by convention it is left unchanged: 3.845 → 3.84.
-
4. The side of a cube is measured with an error of 1%. The percentage error in its volume is:
- 1%
- 2%
- 0.33%
- 3%
Show answer
Answer: D. V = a³, so ΔV/V = 3 × (Δa/a) = 3 × 1% = 3%. A power multiplies the relative error by the power.
-
5. Assertion (A): 12.9 g − 7.06 g should be reported as 5.8 g, not 5.84 g. Reason (R): In subtraction, the result keeps as many significant figures as the input with the fewest significant figures.
- Both A and R are true, and R is the correct explanation of A.
- Both A and R are true, but R is not the correct explanation of A.
- A is true, but R is false.
- A is false, but R is true.
Show answer
Answer: C. The assertion is true: 12.9 − 7.06 = 5.84 by arithmetic, and since 12.9 is known only to one decimal place the result is 5.8 g. The reason is false: for addition and subtraction the rule is about decimal places, not significant figures (both inputs here have three significant figures, yet the result keeps only two).
Sign in to keep track of the lessons you finish.