- Foundation
- About 25 min
- 5 practice questions
Torque on a current loop, magnetic dipole and the moving coil galvanometer
Derive τ = m × B with m = NIA for a current loop, treat a loop as a magnetic dipole, explain the moving coil galvanometer and its sensitivities, and convert it into an ammeter or a voltmeter.
If something looks wrong, please tell us.
By the end of this lesson you can
- Show that a current loop in a uniform field feels zero net force but a torque τ = m × B.
- Define magnetic moment m = NIA and identify stable and unstable equilibrium.
- Explain why a current loop behaves as a magnetic dipole at large distances.
- Describe the moving coil galvanometer, its current and voltage sensitivities, and its conversion to an ammeter and a voltmeter.
Every electric motor and every analogue meter relies on one effect: a current loop in a magnetic field is twisted. This lesson works out that twist, shows that a current loop is the magnetic counterpart of an electric dipole, and then uses it to build an instrument for measuring current and voltage.
Torque on a rectangular loop
A rectangular loop with sides a and b carries current I in a uniform field B. First let B lie in the plane of the loop, parallel to the sides of length a. Those sides feel no force (current parallel to B). The two sides of length b each feel a force IbB, equal and opposite - one into the plane, one out of it. Net force: zero. But the forces act along different lines, forming a couple of arm a, so the torque is τ = IbB × a = IAB, where A = ab.
Now let the normal to the loop make an angle θ with B. The forces on the sides of length a are equal, opposite and collinear, so they cancel with no torque. The forces on the sides of length b are still IbB each, but the arm of the couple shrinks to a sin θ, so τ = IAB sin θ.
τ = m × B, |τ| = mB sin θ, where the magnetic moment m = NIA for a coil of N turns, directed along the normal given by the right-hand thumb rule. Unit of m: A m² (or J T⁻¹). Net force in a uniform field: zero.
- τ = 0 when m is parallel to B: stable equilibrium - a small twist produces a torque that restores it.
- τ = 0 when m is antiparallel to B: unstable equilibrium - a small twist grows.
- This torque is why a compass needle, or any magnetic dipole, lines up with an external field.
- Compare the electric dipole: τ = p × E. A current loop plays the part of p.
Worked example 1: torque on a coil
A square coil of side 5 cm (A = 2.5 × 10⁻³ m²) has 50 turns and carries 2 A. m = NIA = 50 × 2 × 2.5 × 10⁻³ = 0.25 A m². In a uniform field of 0.4 T with its normal at 30° to B: τ = mB sin 30° = 0.25 × 0.4 × 0.5 = 0.05 N m. The largest torque, with the normal at 90° to B, is 0.1 N m. The torque depends only on the area, so a circular coil of the same area and turns would feel the same torque.
The current loop as a magnetic dipole
Far along the axis of a loop (x ≫ R), the field μ₀IR²/[2(x² + R²)^(3/2)] becomes μ₀IR²/(2x³) = (μ₀/4π)(2m/x³), with m = IπR². This has exactly the form of the electric dipole's axial field (1/4πε₀)(2p/x³), with p → m and 1/ε₀ → μ₀. In the plane of the loop, far away, B ≈ (μ₀/4π)(m/x³), matching the electric dipole's equatorial field. So any planar current loop behaves at large distances as a magnetic dipole of moment m = IA.
There is a key difference: an electric dipole is made of two charges, but no isolated magnetic charge (monopole) has ever been found; the current loop is itself the basic magnetic unit. This led Ampere to suggest that all magnetism comes from circulating currents. That is partly true, though particles such as electrons and protons also carry intrinsic magnetic moments not due to circulating currents.
The moving coil galvanometer
A coil of N turns, free to rotate about a fixed axis, sits in a radial magnetic field made by curved pole pieces and a soft iron cylinder (which also strengthens the field). Because the field is radial, the plane of the coil is always along B, so sin θ = 1 and the magnetic torque is NIAB. A spring provides a restoring torque kφ, where k is the torsional constant. At equilibrium:
kφ = NIAB, so φ = (NAB/k) I. The deflection is proportional to the current. Current sensitivity φ/I = NAB/k; voltage sensitivity φ/V = NAB/(kR_G).
How a moving coil galvanometer gives a reading
- Current I enters the coil The coil sits in a strong radial field.
- Magnetic torque NIAB, the same at every angle because the field is radial.
- Spring twists Restoring torque kφ grows with the deflection.
- Balance kφ = NIAB, so the pointer's deflection φ is proportional to I.
Increasing N raises the current sensitivity. But doubling N also roughly doubles the coil's resistance R_G (twice the length of wire), so the voltage sensitivity stays about the same. A galvanometer used as a null detector (as in the Wheatstone bridge) has its zero at the centre of the scale.
Converting a galvanometer into an ammeter and a voltmeter
A galvanometer cannot be used directly as an ammeter: it reaches full-scale deflection at currents of the order of microamperes to milliamperes, and connected in series its relatively large resistance would change the very current it is measuring. A voltmeter, connected in parallel, must draw very little current.
| Feature | Ammeter | Voltmeter |
|---|---|---|
| Connected in the circuit | In series | In parallel |
| Modification | Small shunt resistance S in parallel with G | Large resistance R in series with G |
| Resulting resistance | G S/(G + S) ≈ S, very small | G + R ≈ R, very large |
| Design formula (full-scale current I_g) | S = I_g G/(I − I_g) for range I | R = V/I_g − G for range V |
| Ideal value | Zero resistance | Infinite resistance |
Worked example 2: designing meters
A galvanometer of resistance G = 50 Ω gives full-scale deflection for I_g = 2 mA. (a) For a 0-1 A ammeter: S = I_g G/(I − I_g) = 0.002 × 50 ÷ 0.998 ≈ 0.10 Ω in parallel - almost all the current bypasses the coil. (b) For a 0-10 V voltmeter: R = V/I_g − G = 10 ÷ 0.002 − 50 = 5000 − 50 = 4950 Ω in series.
Worked example 3: why an ammeter needs a small resistance
A 2 V cell drives current through a 4 Ω resistor (current 0.5 A). If the 50 Ω galvanometer itself is put in series to measure the current, the current becomes 2 ÷ 54 ≈ 0.037 A - the meter has wrecked the measurement. With the 0.10 Ω shunt fitted, the meter's resistance is about 0.1 Ω and the current is 2 ÷ 4.1 ≈ 0.49 A, very close to the true 0.5 A.
Key takeaways
- Current loop in uniform B: no net force; torque τ = m × B with m = NIA.
- m ∥ B is stable equilibrium; m antiparallel to B is unstable.
- Far away, a current loop is a magnetic dipole: B_axis = (μ₀/4π)(2m/x³), B_plane = (μ₀/4π)(m/x³).
- Galvanometer: kφ = NIAB in a radial field. Ammeter = G + small shunt in parallel; voltmeter = G + large series resistance.
Check your understanding
-
1. A coil of 20 turns and area 0.01 m² carries 3 A in a uniform field of 0.5 T. What is the maximum torque on it?
- 0.03 N m
- 0.6 N m
- 0.3 N m
- 0.15 N m
Show answer
Answer: C. τ_max = NIAB = 20 × 3 × 0.01 × 0.5 = 0.3 N m, when the field lies in the plane of the coil (m ⊥ B).
-
2. A current loop is in stable equilibrium in a uniform magnetic field when its magnetic moment is
- parallel to the field
- antiparallel to the field
- perpendicular to the field
- at 45° to the field
Show answer
Answer: A. With m parallel to B the torque is zero and a small rotation creates a torque that turns it back, so the equilibrium is stable. Antiparallel is also torque-free but unstable.
-
3. A galvanometer of resistance 40 Ω gives full-scale deflection at 5 mA. What resistance should be connected in series to make it a voltmeter of range 0-5 V?
- 1000 Ω
- 1040 Ω
- 0.2 Ω
- 960 Ω
Show answer
Answer: D. R = V/I_g − G = 5 ÷ 0.005 − 40 = 1000 − 40 = 960 Ω.
-
4. Doubling the number of turns of a galvanometer coil (which also doubles its resistance) will
- double both current and voltage sensitivity
- double the current sensitivity but leave the voltage sensitivity unchanged
- leave both unchanged
- halve the voltage sensitivity
Show answer
Answer: B. Current sensitivity NAB/k doubles with N. Voltage sensitivity NAB/(kR_G) has both N and R_G doubled, so it stays the same.
-
5. Assertion (A): A current-carrying loop placed in a uniform magnetic field experiences no net force. Reason (R): The forces on opposite sides of the loop are equal and opposite.
- Both A and R are true, and R is the correct explanation of A
- Both A and R are true, but R is not the correct explanation of A
- A is true, but R is false
- A is false, but R is true
Show answer
Answer: A. Both are true. In a uniform field, opposite sides of the loop carry current in opposite directions and feel equal and opposite forces, so the net force is zero (though there may be a torque). R explains A.
Sign in to keep track of the lessons you finish.