• Foundation
  • About 24 min
  • 5 practice questions

The photoelectric effect: experimental observations

Describe the apparatus used to study the photoelectric effect, explain saturation current, stopping potential and threshold frequency, and state the four experimental laws.

If something looks wrong, please tell us.

By the end of this lesson you can

  • Describe how Hertz, Hallwachs and Lenard discovered and studied photoelectric emission.
  • Explain how photocurrent depends on intensity and on collector potential.
  • Define saturation current and stopping potential, and use Kₘₐₓ = eV₀.
  • State the threshold frequency and the four laws of the photoelectric effect.

The photoelectric effect is the emission of electrons from a metal when light of suitable frequency falls on it. It sounds simple, but its detailed behaviour could not be explained by the wave theory of light, and that failure opened the way to quantum physics.

Discovery

In 1887, while producing electromagnetic waves with sparks, Heinrich Hertz noticed that sparks across his detector became stronger when the emitter was lit by ultraviolet light from an arc lamp. Wilhelm Hallwachs then showed that a negatively charged zinc plate connected to an electroscope lost its charge under ultraviolet light, that an uncharged plate became positive, and that a positive plate became more positive. Negative charges were being given off. Philipp Lenard found that ultraviolet light on one plate in an evacuated tube made a current flow, which stopped the moment the light was cut off. After 1897 these charges were recognised as electrons, called photoelectrons.

They also found that no electrons come out if the frequency of the light is below a certain minimum, the threshold frequency, which depends on the metal. Zinc, cadmium and magnesium respond only to ultraviolet light, while alkali metals such as lithium, sodium, potassium, rubidium and caesium respond even to visible light.

The apparatus

An evacuated glass tube holds a photosensitive plate C (the emitter) and a metal plate A (the collector). Monochromatic light enters through a quartz window (quartz lets ultraviolet through) and falls on C. A battery keeps A at a potential that can be varied, and a commutator reverses its polarity so A can be positive or negative relative to C. A voltmeter reads the potential and a microammeter reads the photocurrent. Filters change the frequency; moving the lamp changes the intensity.

Effect of intensity

Keep the frequency and the collector potential fixed and increase the intensity. The photocurrent rises in direct proportion to the intensity. Since the current measures how many electrons are emitted per second, the number of photoelectrons emitted per second is proportional to the intensity.

Effect of collector potential

Now fix the frequency and intensity and vary the potential of A. As the positive (accelerating) potential increases, the current rises, then levels off at the saturation current, when every emitted electron reaches A. Raising the potential further changes nothing.

Make A negative (retarding). Now only electrons with enough kinetic energy can push through to A, so the current falls, reaching zero at a sharply defined negative potential V₀, the stopping potential (cut-off potential). At this point even the fastest electrons are just turned back, so:

Kₘₐₓ = ½mv²ₘₐₓ = eV₀, where V₀ is the stopping potential.

Repeat with higher intensities at the same frequency: the saturation current is larger, but the stopping potential is the same. So the maximum kinetic energy of photoelectrons does not depend on intensity.

Effect of frequency

Adjust the intensity to be the same at several frequencies. The saturation current is now the same, but the stopping potential is larger (more negative) for higher frequency. A graph of V₀ against frequency ν is a straight line for a given metal, cutting the frequency axis at the threshold frequency ν₀, where V₀ = 0. Below ν₀ there is no emission at all, however intense the light. Above ν₀, emission begins with no measurable delay (within about 10⁻⁹ s) even for very dim light.

What intensity and frequency each control

  • Increase intensity (frequency fixed, above ν₀)
    • More electrons per second
    • Photocurrent and saturation current increase in proportion
    • Stopping potential unchanged
    • Maximum kinetic energy unchanged
  • Increase frequency (intensity fixed)
    • Below ν₀: no emission at all
    • Above ν₀: stopping potential increases linearly
    • Maximum kinetic energy increases
    • Saturation current roughly unchanged

The four laws of photoelectric emission

  1. For a given metal and frequency (above threshold), the photocurrent is proportional to the intensity of light.
  2. For a given metal and frequency, the saturation current is proportional to intensity, but the stopping potential is independent of intensity.
  3. For each metal there is a threshold frequency below which no emission occurs, however intense the light. Above it, the stopping potential (and Kₘₐₓ) increases linearly with frequency and does not depend on intensity.
  4. Emission is instantaneous: there is no noticeable time lag (about 10⁻⁹ s or less), even for very dim light.

Worked example 1: stopping potential to energy and speed

The stopping potential in an experiment is 2.0 V. Kₘₐₓ = eV₀ = 2.0 eV = 2.0 × 1.6 × 10⁻¹⁹ = 3.2 × 10⁻¹⁹ J. Maximum speed: vₘₐₓ = √(2Kₘₐₓ/m) = √(2 × 3.2 × 10⁻¹⁹ / 9.1 × 10⁻³¹) = √(7.03 × 10¹¹) ≈ 8.4 × 10⁵ m s⁻¹.

Worked example 2: reading the curves

Two curves of photocurrent against collector potential are drawn for the same metal and the same frequency; curve 2 saturates at 3 times the current of curve 1. Reasoning: saturation current is proportional to intensity, so light 2 is 3 times as intense. Both curves must meet the voltage axis at the same stopping potential, because the frequency is the same. If curve 2 had a larger stopping potential, the frequency, not just the intensity, would have to be higher.

Key takeaways

  • Photocurrent ∝ intensity; saturation current is reached when all emitted electrons are collected.
  • Stopping potential measures the maximum kinetic energy: Kₘₐₓ = eV₀.
  • V₀ depends on frequency and metal, not on intensity.
  • Below the threshold frequency there is no emission; above it, emission is instantaneous.

Check your understanding

  1. 1. In a photoelectric experiment the light intensity is doubled while the frequency is kept the same (above threshold). Which statement is correct?

    1. The stopping potential doubles
    2. The saturation current doubles and the stopping potential is unchanged
    3. Both the saturation current and the stopping potential double
    4. No change occurs in the photocurrent
    Show answer

    Answer: B. Intensity decides how many electrons are emitted per second, so the saturation current doubles. The stopping potential measures the maximum kinetic energy, which does not depend on intensity, so it stays the same.

  2. 2. The stopping potential for photoelectrons from a metal is 0.8 V. The maximum kinetic energy of the photoelectrons is

    1. 0.8 J
    2. 5.0 × 10⁻²⁰ J
    3. 1.6 × 10⁻¹⁹ J
    4. 1.28 × 10⁻¹⁹ J
    Show answer

    Answer: D. Kₘₐₓ = eV₀ = (1.6 × 10⁻¹⁹ C)(0.8 V) = 1.28 × 10⁻¹⁹ J, which is 0.8 eV.

  3. 3. The saturation current in a photocell is reached when

    1. every emitted photoelectron reaches the collector
    2. the light frequency equals the threshold frequency
    3. the collector is at the stopping potential
    4. the emitter stops emitting electrons
    Show answer

    Answer: A. As the accelerating potential rises, more of the emitted electrons are collected. Once all of them reach the collector, the current cannot rise further: that is saturation.

  4. 4. Very dim light of frequency above the threshold falls on a metal. Photoelectrons are emitted

    1. only after several hours
    2. only if the light is made more intense
    3. almost instantly, within about 10⁻⁹ s
    4. only if the collector is negative
    Show answer

    Answer: C. Experiments show no measurable time lag above the threshold frequency, however dim the light. Dim light only means fewer electrons per second.

  5. 5. Assertion (A): Light of frequency below the threshold frequency cannot eject photoelectrons from a metal however intense it is. Reason (R): The number of photoelectrons emitted per second is proportional to the intensity of light.

    1. Both A and R are true, and R is the correct explanation of A
    2. Both A and R are true, but R is not the correct explanation of A
    3. A is true, but R is false
    4. A is false, but R is true
    Show answer

    Answer: B. Both statements are experimental facts. But R concerns the number of electrons when emission does occur; it does not explain why no emission occurs below threshold. That needs the photon idea of the next lesson. So R is not the explanation of A.

Sign in to keep track of the lessons you finish.

Next lesson → Einstein's photoelectric equation

Privacy · Terms · Refunds · Delivery