• Foundation
  • About 13 min
  • 5 practice questions

Points, line segments, lines and rays

Tell a point, a line segment, a line and a ray apart, name each one correctly with capital letters, and count how many lines pass through given points.

If something looks wrong, please tell us.

By the end of this lesson you can

  • Describe a point, a line segment, a line and a ray, with an everyday model of each.
  • Name segments, lines and rays correctly, knowing when the order of letters matters.
  • Say how many lines can pass through one point and through two points.

Every shape you will meet in geometry, from a triangle to a star, is built from a few simple ideas: points, segments, lines, rays and angles. These ideas are the building blocks of plane geometry, the geometry of flat surfaces like a sheet of paper. In this lesson we meet the first four.

Point

A point marks an exact location. It has no length, no width and no height. A dot made with a very sharp pencil, the tip of a needle or the corner of a table top are good models of a point, but a real point is imagined to be invisibly small. We name a point with a capital letter, such as point P or point Z.

Line segment

Mark two points A and B on paper. There are many paths from A to B, some curved and some zig-zag, but only one is the shortest: the straight path. This shortest path, including A and B, is the line segment AB (it can also be called BA). A and B are its end points. A segment has a definite length that you can measure with a ruler. The edge of a ruler or the crease made by folding paper are models of a segment.

Line

Now imagine the segment AB extended beyond A and beyond B, without ever stopping. This is the line AB. A line has no end points and goes on for ever in both directions, so we can only ever draw part of it, with arrowheads at both ends to show that it continues. A line may also be named with a small letter, such as line l or line m.

Ray

A ray starts at one point and goes on for ever in one direction. A beam from a torch or a lighthouse is a model of a ray. A ray that starts at A and passes through P is named ray AP. The starting point is always written first, so ray AP and ray PA are different rays: one starts at A, the other at P.

Segment, line and ray

  • Line segment AB
    • Two end points
    • Fixed length
    • AB and BA name the same segment
  • Line AB
    • No end points
    • Goes on for ever both ways
    • Can be named with a small letter, like l
  • Ray AP
    • One starting point, A
    • Goes on for ever one way
    • Starting point written first

How many lines?

  • Through one point you can draw as many lines as you like: they can point in every direction.
  • Through two different points there is exactly one line. Two points fix a line.
  • Three points may or may not lie on one line. If they do not, joining them in pairs gives 3 different lines.

Two points fix exactly one line. A segment has two end points, a ray has one starting point, and a line has none.

Worked example 1: naming parts of a figure

Points P, Q, R and S lie on a line in that order, and point T lies outside the line. (a) Segments on the line: PQ, PR, PS, QR, QS, RS, which is 6 segments. (b) Rays that start at Q and run along the line: ray QP (towards P) and ray QR (towards R, which passes through S as well, so it is also ray QS). (c) The line can be named PQ, PS, QR or by any two of its points. (d) T is not on the line, so 'line PT' is a different line.

Worked example 2: one ray, two names

A ray starts at O and passes through A and then B. Can it be called ray OB? Yes: it starts at O and B lies on it, so ray OA and ray OB are the same ray. Can it be called ray AO? No: ray AO would start at A and go through O, in the opposite direction. The starting point decides the ray.

Worked example 3: lines through four points

Four points A, B, C and D are placed so that no three lie on one line. Each pair gives one line: AB, AC, AD, BC, BD, CD. So there are 6 lines. Counting with a pattern: A joins 3 others, B joins 2 new ones, C joins 1 new one: 3 + 2 + 1 = 6.

Key takeaways: a point is a location; a segment is the shortest path between two end points; a line goes on for ever both ways; a ray starts at one point and goes on for ever one way. In naming a ray, the starting point comes first. Exactly one line passes through two points, while countless lines pass through one point.

Check your understanding

  1. 1. Which of these has exactly two end points?

    1. A line
    2. A ray
    3. A line segment
    4. A point
    Show answer

    Answer: C. A line segment runs from one end point to another. A line has no end points, a ray has only a starting point, and a point is just a location.

  2. 2. Meera marks two points on her page. How many different straight lines can she draw that pass through both points?

    1. Exactly one
    2. Two
    3. None
    4. As many as she likes
    Show answer

    Answer: A. Two different points fix exactly one line. Through a single point, however, she could draw as many lines as she likes.

  3. 3. A ray starts at K and passes through L. Which name is correct?

    1. Ray LK
    2. Segment KL
    3. Line K
    4. Ray KL
    Show answer

    Answer: D. A ray is named with its starting point first, then another point on it, so it is ray KL. Ray LK would start at L and point the other way.

  4. 4. Points E, F and G lie on one line in that order. How many line segments can be named using only these three points?

    1. 2
    2. 3
    3. 4
    4. 6
    Show answer

    Answer: B. The segments are EF, FG and EG. That makes 3 segments (EF and FE are the same segment, so they are not counted twice).

  5. 5. Which everyday object is the best model of a ray?

    1. The beam of light from a torch
    2. The edge of a ruler
    3. The tip of a compass
    4. A folded crease on paper
    Show answer

    Answer: A. A torch beam starts at the torch and keeps going in one direction, like a ray. A ruler's edge and a crease have two ends (segments), and a compass tip models a point.

Sign in to keep track of the lessons you finish.

Next lesson → Angles: vertex, arms and size

Privacy · Terms · Refunds · Delivery