• Practice
  • About 15 min
  • 5 practice questions

Air pollution: pollutants, smog and control devices

Classify air pollutants as primary or secondary, tell the two kinds of smog apart, match each control device to the pollutant it removes, and calculate overall removal efficiency.

If something looks wrong, please tell us.

Air pollution questions look like pure memory work, but they are full of pairs that are easy to swap: primary and secondary, classical and photochemical smog, scrubber and precipitator. They also include one reliable calculation, the efficiency of control devices. This lesson organises the facts into contrasts and gives you a quick method for the arithmetic.

Primary and secondary pollutants

A primary pollutant is emitted directly from a source in the harmful form: carbon monoxide from incomplete burning, sulphur dioxide from burning coal and oil that contain sulphur, nitric oxide from high-temperature combustion in engines and furnaces, unburnt hydrocarbons, and particulate matter such as soot, dust and fly ash. A secondary pollutant is not emitted directly but forms in the air by reactions between primary pollutants, often helped by sunlight. Ground-level ozone, peroxyacetyl nitrate (PAN) and droplets of sulphuric acid are secondary pollutants.

Carbon monoxide is dangerous because it binds to haemoglobin far more strongly than oxygen does, forming carboxyhaemoglobin and reducing the blood's ability to carry oxygen. Particulate matter is described by size: PM10 means particles 10 micrometres or smaller and PM2.5 means 2.5 micrometres or smaller. The finer the particle, the deeper it can travel into the lungs, so PM2.5 is the more harmful.

Two kinds of smog

Comparing the two smogs
FeatureClassical (sulphurous) smogPhotochemical smog
Main ingredientsSmoke, soot, sulphur dioxide, fogNitrogen oxides, hydrocarbons, sunlight
WeatherCool, humid, often in winterWarm, dry and sunny
ProductsSulphuric acid droplets and sootOzone, PAN, aldehydes
Chemical natureReducingOxidising

Both kinds are made worse by a temperature inversion, when a layer of warm air above traps cooler polluted air near the ground and stops it rising and dispersing.

Control devices

  • Electrostatic precipitator: gives particles an electric charge so they are attracted to collecting plates; it removes a very high proportion of particulate matter from power-plant exhaust.
  • Scrubber: sprays water or a lime slurry through the exhaust to dissolve or react with gases such as sulphur dioxide.
  • Cyclone separator: spins the gas so heavier particles are thrown out; good for coarse dust.
  • Catalytic converter: in vehicle exhausts, metals such as platinum, palladium and rhodium convert carbon monoxide and hydrocarbons to carbon dioxide and water and nitric oxide to nitrogen gas. Vehicles with converters must use unleaded petrol, because lead inactivates the catalyst.

Worked example 1: devices in series

Flue gas passes through a cyclone that removes 80 percent of the dust and then an electrostatic precipitator that removes 99 percent of what remains. Do not add the percentages. Track what passes through: 20 percent leaves the cyclone, and 1 percent of that leaves the precipitator. Fraction escaping = 0.20 × 0.01 = 0.002, that is 0.2 percent. Overall efficiency = 100 − 0.2 = 99.8 percent.

Worked example 2: mass escaping

A chimney receives 500 kg of dust a day and its precipitator is 98 percent efficient. Dust escaping = 500 × 0.02 = 10 kg a day; dust collected = 490 kg. If a second identical precipitator is added after the first, only 2 percent of 10 kg, that is 0.2 kg, escapes.

Common traps

Three traps recur in practice sets. First, ozone is a secondary pollutant at ground level even though it is a natural and useful gas high in the stratosphere; the question will tell you which height it means. Second, carbon dioxide is not the gas that poisons people in a closed room with a smoky stove; carbon monoxide is. Third, a catalytic converter does not remove carbon dioxide; it produces it, by oxidising carbon monoxide and hydrocarbons. When two options look alike, ask whether the device or process removes particles or gases, and whether the pollutant is emitted or formed in the air.

Secondary pollutants form in the air (ozone, PAN, acid droplets). Classical smog: SO2 + smoke + fog, reducing. Photochemical smog: NOx + hydrocarbons + sunlight, oxidising. Devices in series: multiply the fractions that pass through.

Key takeaways: learn pollutants as pairs and contrasts. CO harms by binding haemoglobin; finer particles are worse. Precipitators remove particles, scrubbers remove gases, catalytic converters treat CO, hydrocarbons and NO and need unleaded fuel. For several devices, multiply the fractions escaping, then subtract from 100.

Check your understanding

  1. 1. Which of these is a secondary air pollutant?

    1. Ground-level ozone
    2. Carbon monoxide
    3. Sulphur dioxide
    4. Soot
    Show answer

    Answer: A. Ground-level ozone forms in the air from nitrogen oxides and hydrocarbons in sunlight. The other three are emitted directly.

  2. 2. Photochemical smog forms mainly from:

    1. Sulphur dioxide and smoke in cold fog
    2. Carbon dioxide and water vapour at night
    3. Nitrogen oxides and hydrocarbons reacting in sunlight
    4. Dust storms in dry weather
    Show answer

    Answer: C. Photochemical smog needs nitrogen oxides, hydrocarbons and sunlight; it forms ozone and PAN in warm sunny weather.

  3. 3. Exhaust passes through a device that removes 90 percent of the particles and then a second that removes 95 percent of what remains. What is the overall removal efficiency?

    1. 92.5 percent
    2. 99.5 percent
    3. 85.5 percent
    4. 97.5 percent
    Show answer

    Answer: B. Fraction escaping = 0.10 × 0.05 = 0.005, that is 0.5 percent. Overall = 100 − 0.5 = 99.5 percent.

  4. 4. Why is carbon monoxide poisonous?

    1. It dissolves the walls of the lungs
    2. It turns into ozone in the blood
    3. It blocks the absorption of sugar in the gut
    4. It binds to haemoglobin more strongly than oxygen and reduces oxygen transport
    Show answer

    Answer: D. CO forms carboxyhaemoglobin, so less haemoglobin is available to carry oxygen to the tissues.

  5. 5. Why must vehicles fitted with catalytic converters use unleaded petrol?

    1. Lead increases the efficiency of the catalyst too much
    2. Unleaded petrol contains the platinum needed by the converter
    3. Lead is converted into ozone by the converter
    4. Lead inactivates the catalyst
    Show answer

    Answer: D. Lead coats and poisons the metal catalyst, so the converter stops working.

Privacy · Terms · Refunds · Delivery