- Practice
- About 14 min
- 5 practice questions
Speed set: ppm, dilution and unit traps
Practise the unit conversions and quick calculations that decide many numerical questions: ppm, percentages, mg and µg, dilution, BOD and daily loads.
If something looks wrong, please tell us.
The arithmetic in pollution questions is simple. The marks are lost on units. A micro is mistaken for a milli, a percentage for a part per million, a day for a second. This lesson collects the conversions you need and then runs through a speed set. Work each step and write the unit next to every number.
Conversions to hold
| Conversion | Value |
|---|---|
| 1 mg | 1,000 µg |
| 1 g | 1,000 mg |
| 1 tonne | 1,000 kg |
| 1 mg/L in water | 1 g/m³, about 1 ppm |
| 1 ppm | 0.0001 percent, since 1% = 10,000 ppm |
| 1 ppb | 0.001 ppm |
| 1 day | 86,400 seconds |
| 1 m³ | 1,000 litres |
For dilution use C₁V₁ = C₂V₂: the amount of the substance before and after dilution is the same. For BOD use BOD = (D1 − D2) ÷ P, where P is the volume of the sample divided by the volume of the bottle. For devices in series, multiply the fractions that escape.
Worked example 1: dilution and BOD
Example 1. 10 mL of a solution at 400 mg/L is made up to 200 mL. What is the new concentration? Working: C₂ = C₁V₁ ÷ V₂ = 400 × 10 ÷ 200 = 20 mg/L. For BOD, take 7.5 mL of sewage diluted to 250 mL. P = 7.5 ÷ 250 = 0.03. Initial DO is 8.6 mg/L and DO after 5 days is 4.7 mg/L. Oxygen used = 3.9 mg/L. BOD = 3.9 ÷ 0.03 = 130 mg/L. Without dividing by P, you would report 3.9 mg/L, which is 33 times too low.
Worked example 2: ppm and percent
Example 2. An air sample contains 250 ppm of CO₂ more than a baseline reading. Express this as a percentage. Working: 1% = 10,000 ppm, so 250 ppm = 250 ÷ 10,000 = 0.025%. Next convert 0.5 mg/L to micrograms per litre: 0.5 × 1,000 = 500 µg/L. In water, 0.5 mg/L is about 0.5 ppm. A wrong turn would be to divide by 1,000 instead of multiplying, which is why the direction of each conversion should be checked: a smaller unit has a larger number.
Worked example 3: daily load
Example 3. A factory discharges 0.4 m³/s of water containing 8 mg/L of a pollutant. Find the mass released per day in kg. Working: 8 mg/L = 8 g/m³. Load = 8 × 0.4 = 3.2 g/s. Per day = 3.2 × 86,400 = 276,480 g = 276.48 kg. Check that the units line up: (g/m³) × (m³/s) = g/s, and then seconds into days.
Traps to avoid
- Reading 'percent removed' as 'percent left': a unit that removes 80% leaves 20%.
- Using the wrong base: a percentage fall is divided by the starting value.
- Forgetting that two devices in series do not remove the sum of their percentages.
- Mixing mg/L with µg/L between steps.
Write the unit with every number. Smaller unit, larger number. 1 mg/L = 1 g/m³ = about 1 ppm. 1% = 10,000 ppm.
Key takeaways: convert before you calculate; use C₁V₁ = C₂V₂ for dilution; divide BOD by the dilution fraction; and finish with a sanity check on the size of the answer.
Check your understanding
-
1. 5 mL of a solution at 600 mg/L is made up to 100 mL. What is the new concentration?
- 30 mg/L
- 3,000 mg/L
- 120 mg/L
- 6 mg/L
Show answer
Answer: A. C₂ = 600 × 5 ÷ 100 = 30 mg/L.
-
2. A reading of 50 ppm equals what percentage?
- 0.5%
- 0.05%
- 0.005%
- 5%
Show answer
Answer: C. 1% = 10,000 ppm, so 50 ppm = 50 ÷ 10,000 = 0.005%.
-
3. A device removes 80% of a pollutant, and a second device removes 50% of what is left. What fraction escapes?
- 30%
- 10%
- 0%
- 40%
Show answer
Answer: B. Escaping fraction = 0.20 × 0.50 = 0.10, which is 10%. Adding the removals would give an impossible 130%.
-
4. An effluent flows at 0.1 m³/s with 20 mg/L of a pollutant. What mass is released per day?
- 17.28 g
- 172.8 g
- 1,728 g
- 172.8 kg
Show answer
Answer: D. Load = 20 g/m³ × 0.1 m³/s = 2 g/s. Per day = 2 × 86,400 = 172,800 g = 172.8 kg.
-
5. Express 0.25 mg/L in µg/L.
- 250 µg/L
- 0.25 µg/L
- 25 µg/L
- 2,500 µg/L
Show answer
Answer: A. 1 mg = 1,000 µg, so 0.25 × 1,000 = 250 µg/L.
Sign in to keep track of the lessons you finish.