Revision notes

Heat and Thermodynamics: Practice

The key points, rules to remember, tables and diagrams from all 9 lessons, on one page for quick revision. To keep a copy, use your browser's Print and choose "Save as PDF".

Lesson 1

Temperature scales and thermal expansion

C/5 = (F − 32)/9 = (K − 273)/5. ΔL = αLΔT, β = 2α, γ = 3α. Water has maximum density at 4°C.

— Remember
  • Use C/5 = (F − 32)/9 = (K − 273)/5 for conversions.
  • The coefficients are in the ratio α : β : γ = 1 : 2 : 3.
  • Temperature differences are the same in °C and K.
Read the full lesson

Lesson 2

Specific heat and calorimetry

Q = mcΔT. Heat lost by hot bodies = heat gained by cold bodies. Water has a high specific heat, so it heats up and cools down slowly.

— Remember
  • Write heat lost = heat gained and solve for the final temperature.
  • Check that the final temperature lies between the two initial temperatures.
  • Keep units consistent: either all SI or all cal/g°C.
Read the full lesson

Lesson 3

Latent heat and change of state

Q = mL during a change of state at constant temperature. For mixtures, first check whether the ice will melt completely before assuming a final temperature.

— Remember
  • Temperature stays constant during a change of state.
  • Add the heat for every stage of the process.
  • In ice mixtures, check whether all the ice melts before solving.
Read the full lesson

Lesson 4

Conduction, convection and radiation

Q/t = kA ΔT/L. P ∝ T⁴ (T in kelvin). Radiation needs no medium; convection needs a fluid.

— Remember
  • Conduction rate is proportional to area and temperature difference, and inversely proportional to thickness.
  • Radiated power depends on T⁴, with T in kelvin.
  • Only radiation can travel through a vacuum.
Read the full lesson

Lesson 5

Laws of thermodynamics and heat engines

Special processes of an ideal gas
ProcessConditionConsequence
IsothermalT constantΔU = 0, so Q = W
IsochoricV constantW = 0, so Q = ΔU
IsobaricP constantW = PΔV
AdiabaticNo heat exchangeQ = 0, so W = −ΔU

ΔU = Q − W. Isothermal: ΔU = 0. Adiabatic: Q = 0. Carnot efficiency = 1 − T₂/T₁ (in kelvin). No engine is 100% efficient.

— Remember
  • First law is conservation of energy; keep the signs of Q and W consistent.
  • Always convert °C to kelvin in efficiency and gas-law problems.
  • Efficiency is limited by the temperatures of the reservoirs and is always below 100%.
Read the full lesson

Lesson 6

Gas law problems: combined law, moles and common traps

Convert to kelvin. Use absolute pressure. For an open vessel n ∝ 1/T. For a fixed mass, density ∝ P/T.

— Rule to remember
  • Cross out the constant quantity and solve.
  • Use SI units for PV = nRT.
  • Add atmospheric pressure to a gauge reading.
Read the full lesson

Lesson 7

Electrical heating and calorimetry with power

Energy = P t. Heat = m c ΔT. With efficiency, useful energy = η P t. For flowing water, P = (mass per second) × c × ΔT.

— Rule to remember
  • Set heater energy equal to heat gained, then solve.
  • Mixing the same liquid at different temperatures gives a weighted average.
  • 1 kWh equals 3.6 × 10⁶ J.
Read the full lesson

Lesson 8

Newton's law of cooling and cooling-rate problems

Rate of cooling ∝ (T − T₀). Use the average temperature for an interval: (T₁ − T₂)/t = k[(T₁ + T₂)/2 − T₀]. Rate of fall of temperature ∝ 1/(m c).

— Rule to remember
  • Calculate the excess over the surroundings, not the temperature itself.
  • The cooling slows down as the excess falls.
  • Liquids of lower specific heat cool faster.
Read the full lesson

Lesson 9

PV diagrams, cycles, efficiency and the refrigerator

Work = area under the P–V curve. Cycle: ΔU = 0, so W = Q_in − Q_out, and η = W/Q_in. Refrigerator: COP = Q₂/W = T₂/(T₁ − T₂).

— Rule to remember
  • The enclosed area of a cycle is the net work.
  • Clockwise cycles produce work, anticlockwise cycles use it.
  • For a full cycle the net heat equals the net work.
  • COP can be greater than 1 because the refrigerator moves heat instead of making it.
Read the full lesson

Privacy · Terms · Refunds · Delivery