- Practice
- About 14 min
- 5 practice questions
Electrical heating and calorimetry with power
Solve problems on immersion heaters, efficiency, geysers, electrical measurement of specific heat and the mixing of three liquids.
If something looks wrong, please tell us.
Calorimetry questions often involve a heater, so they mix the ideas of power and heat. The key link is simple: energy supplied = power × time, and heat absorbed = m c ΔT. In this lesson the values are made up for practice. Use c(water) = 4200 J/kg °C.
Basic relations
- Energy from a heater: E = P t = V I t (in joules, when P is in watts and t in seconds).
- Heat absorbed: Q = m c ΔT.
- With efficiency η: useful energy = η × P × t.
- Heat flow rate in a geyser (flowing water): P = (mass flowing per second) × c × ΔT.
- 1 kilowatt-hour (kWh) = 1000 W × 3600 s = 3.6 × 10⁶ J.
Worked example 1: an immersion heater with losses
A 2000 W heater is 80 percent efficient and heats 5 kg of water through 40 °C. Heat needed = 5 × 4200 × 40 = 840 000 J. Useful power = 0.8 × 2000 = 1600 W. Time = 840 000/1600 = 525 s, which is about 8.75 minutes.
Worked example 2: electrical method for specific heat
A metal block of mass 0.5 kg is heated by a heater working at 12 V and 5 A for 300 s. Energy = V I t = 12 × 5 × 300 = 18 000 J. The temperature of the block rises by 20 °C. Assuming no loss, c = Q/(mΔT) = 18 000/(0.5 × 20) = 1800 J/kg °C. In practice, some heat is lost, so the real value is a little lower; wrapping the block in insulation reduces the error.
Worked example 3: a geyser
Water flows through a geyser at 3 kg per minute, which is 0.05 kg every second, and its temperature must rise by 30 °C. The power needed is P = 0.05 × 4200 × 30 = 6300 W = 6.3 kW, assuming that all the heat goes into the water.
Worked example 4: mixing three liquids
Three portions of water are mixed: 100 g at 20 °C, 200 g at 40 °C and 300 g at 60 °C. For the same liquid, the final temperature is the weighted average: T = (100 × 20 + 200 × 40 + 300 × 60)/(100 + 200 + 300) = (2000 + 8000 + 18 000)/600 = 28 000/600 = 46.7 °C. This lies between 20 °C and 60 °C, as it must.
Worked example 5: kilowatt-hours
A 2 kW heater is on for 30 minutes, or 0.5 hour. The energy used is 2 × 0.5 = 1 kWh = 3.6 × 10⁶ J. This could heat 3.6 × 10⁶/4200 = 857 kg of water through 1 °C.
Common traps
- Convert minutes to seconds and grams to kilograms before using the formulas.
- Efficiency applies to the heater's output, so do not divide the wrong way: time = Q/(η P).
- If the container (calorimeter) also warms, add its water equivalent to the water.
Energy = P t. Heat = m c ΔT. With efficiency, useful energy = η P t. For flowing water, P = (mass per second) × c × ΔT.
Key takeaways
- Set heater energy equal to heat gained, then solve.
- Mixing the same liquid at different temperatures gives a weighted average.
- 1 kWh equals 3.6 × 10⁶ J.
Check your understanding
-
1. A 1000 W heater runs for 2 minutes with no loss. The heat produced is:
- 2000 J
- 120 000 J
- 1000 J
- 60 000 J
Show answer
Answer: B. E = P t = 1000 × 120 = 120 000 J.
-
2. A heater has an efficiency of 50 percent and a power of 2000 W. To give 100 000 J to water it must run for:
- 50 s
- 25 s
- 200 s
- 100 s
Show answer
Answer: D. Useful power = 1000 W, so t = 100 000/1000 = 100 s.
-
3. A 12 V heater with a current of 2 A runs for 100 s. The energy is:
- 24 J
- 2400 J
- 1200 J
- 600 J
Show answer
Answer: B. E = V I t = 12 × 2 × 100 = 2400 J.
-
4. 100 g of water at 10 °C and 300 g of water at 50 °C are mixed. The final temperature is:
- 30 °C
- 35 °C
- 45 °C
- 40 °C
Show answer
Answer: D. T = (100 × 10 + 300 × 50)/400 = 16 000/400 = 40 °C.
-
5. An energy of 1 kWh, expressed in joules, is:
- 3.6 × 10⁶ J
- 1000 J
- 3600 J
- 3.6 × 10⁴ J
Show answer
Answer: A. 1 kWh = 1000 W × 3600 s = 3.6 × 10⁶ J.
Sign in to keep track of the lessons you finish.