• Foundation
  • About 14 min
  • 5 practice questions

Expansion and contraction in daily life

Explain why gaps are left in railway tracks and bridges, use ΔL = αLΔT, and understand bimetallic strips and the unusual behaviour of water.

If something looks wrong, please tell us.

Walk on a railway bridge and you may notice small gaps between the steel plates. Look at an overhead wire in summer and you will see it sag. These are not careless design; they are the result of a basic fact: most materials expand when heated and contract when cooled. This lesson shows the effects, the simple calculation, and the one important exception, water.

Expansion of solids, liquids and gases

  • Solids expand a little. Different solids expand by different amounts.
  • Liquids expand more than solids for the same rise in temperature, which is why the mercury or coloured alcohol in a thermometer rises in a thin tube.
  • Gases expand the most.
  • The cause is that particles vibrate more and push slightly further apart when heated.

Expansion in daily life

  • Railway tracks have small gaps between rails and bridges have expansion joints, so they do not buckle in summer heat.
  • Overhead telephone and power wires are left slightly slack in summer, so that they are not too tight and snap in winter.
  • A tight metal lid on a glass jar can be loosened by dipping it in hot water: the metal expands more than the glass.
  • Petrol tanks are not filled to the brim, since petrol expands as it warms.
  • Thick glass can crack when hot water is poured in, because the inside expands faster than the outside.

The simple formula

The increase in length of a rod is proportional to its original length L and the rise in temperature ΔT: ΔL = α L ΔT. The constant α is the coefficient of linear expansion of the material and its unit is per °C. In the examples below take α = 1.2 × 10⁻⁵ per °C for steel.

Bimetallic strip

Two strips of different metals, such as brass and iron, riveted together make a bimetallic strip. On heating, brass expands more than iron, so the strip bends with brass on the outer side of the curve. This is used in the thermostat of an electric iron, where the bending strip breaks the circuit when the iron is hot enough, and in fire alarms.

Worked examples

Example 1. A steel rail 20 m long is heated through 40 °C. ΔL = 1.2 × 10⁻⁵ × 20 × 40 = 9.6 × 10⁻³ m = 9.6 mm. The gap left between rails must be bigger than this.

Example 2. A 100 m steel bridge goes from 10 °C in winter to 50 °C in summer. ΔT = 40 °C. ΔL = 1.2 × 10⁻⁵ × 100 × 40 = 0.048 m = 4.8 cm. The expansion joints must allow at least 4.8 cm.

Example 3 (water is different). Most liquids contract on cooling, but water contracts only until 4 °C and then expands as it cools towards 0 °C. Water has its maximum density at 4 °C. In a pond in winter, surface water cools, becomes denser and sinks until the whole pond is at 4 °C. After that the cooler surface water is lighter, stays on top, and freezes. The ice floats on top, and the water below stays near 4 °C, so fish and plants survive.

ΔL = α L ΔT. Solids expand a little, liquids more, gases most. Water is densest at 4 °C.

— Rule to remember

Key takeaways

  • Materials usually expand on heating and contract on cooling.
  • Gaps and joints let structures expand safely.
  • A bimetallic strip bends when heated because the two metals expand by different amounts.
  • Water is an exception between 0 °C and 4 °C, which lets lakes freeze from the top.

Check your understanding

  1. 1. Small gaps are left between steel rails mainly so that:

    1. Rails can expand in summer without bending
    2. Trains can run faster over the joints
    3. Rain water can drain away between rails
    4. Rails can be fitted more cheaply by builders
    Show answer

    Answer: A. The rails lengthen when heated. Gaps give room so that they do not buckle.

  2. 2. For the same rise in temperature, which expands the most?

    1. A solid
    2. A liquid
    3. A gas
    4. All expand equally
    Show answer

    Answer: C. Gases expand much more than liquids, and liquids more than solids.

  3. 3. A steel rod 10 m long is heated by 50 °C (α = 1.2 × 10⁻⁵ per °C). Its increase in length is:

    1. 0.6 mm
    2. 6 mm
    3. 60 mm
    4. 0.06 mm
    Show answer

    Answer: B. ΔL = 1.2 × 10⁻⁵ × 10 × 50 = 6 × 10⁻³ m = 6 mm.

  4. 4. Water has its greatest density at:

    1. 0 °C
    2. 100 °C
    3. −4 °C
    4. 4 °C
    Show answer

    Answer: D. Water is densest at 4 °C. That is why a frozen pond is at about 4 °C below the ice.

  5. 5. The thermostat of an electric iron uses:

    1. A mercury thermometer inside the iron
    2. A bimetallic strip
    3. A convex lens in the handle
    4. A magnet fixed beside the plate
    Show answer

    Answer: B. A bimetallic strip bends on heating and breaks the circuit when the iron reaches the set temperature.

Privacy · Terms · Refunds · Delivery