• Practice
  • About 20 min
  • 5 practice questions

Extraction of aluminium, copper and iron

Describe the extraction of aluminium (Baeyer's and Hall's processes), copper from copper pyrites and iron in the blast furnace, and write the main balanced equations and properties of each metal.

If something looks wrong, please tell us.

By the end of this lesson you can

  • Describe how bauxite is turned into alumina and then into aluminium.
  • List the stages in extracting copper from copper pyrites.
  • Explain the three zones of the blast furnace in the extraction of iron.
  • Write and check the key equations, and state important properties and uses.

Aluminium, copper and iron are the three metals the Tamil Nadu textbook studies in detail. They are extracted in very different ways because they differ in reactivity: aluminium needs electricity, while copper and iron can be freed by heating with air or carbon.

Aluminium

Aluminium is the most abundant metal in the Earth's crust. Being reactive, it occurs only in compounds: bauxite (Al₂O₃·2H₂O, the chief ore), cryolite (Na₃AlF₆) and corundum (Al₂O₃). Extraction has two stages.

  1. Baeyer's process (bauxite to alumina): powdered bauxite is heated under pressure with concentrated sodium hydroxide at about 150 °C: Al₂O₃ + 2NaOH → 2NaAlO₂ + H₂O. Diluting the sodium meta-aluminate with water precipitates aluminium hydroxide: NaAlO₂ + 2H₂O → Al(OH)₃ + NaOH. This is filtered, washed, dried and heated at about 1000 °C: 2Al(OH)₃ → Al₂O₃ + 3H₂O.
  2. Hall's process (electrolysis of alumina): pure alumina is dissolved in molten cryolite with fluorspar, which lowers the melting temperature. The cathode is an iron tank lined with graphite; the anode is a set of graphite rods. At about 900-950 °C and 5-6 V, aluminium collects at the cathode and oxygen is released at the anode (where it burns the graphite to CO₂). Overall: 2Al₂O₃ → 4Al + 3O₂.

Worked example 1: checking an aluminium equation

Question: Check that 2Al + 2NaOH + 2H₂O → 2NaAlO₂ + 3H₂ is balanced.

Working: Al: 2 on the left, 2 on the right. Na: 2 and 2. O: 2 (from NaOH) + 2 (from H₂O) = 4 on the left; 2 × 2 = 4 on the right. H: 2 + 4 = 6 on the left; 3 × 2 = 6 on the right. Balanced. It shows that aluminium dissolves in strong alkali, giving hydrogen.

Aluminium: key reactions
WithEquationNote
Air, strongly heated (about 800 °C)4Al + 3O₂ → 2Al₂O₃; 2Al + N₂ → 2AlNBurns brightly; dry air at room temperature has no effect
Steam over red-hot metal2Al + 3H₂O → Al₂O₃ + 3H₂Cold water does not react because of the oxide layer
Dilute hydrochloric acid2Al + 6HCl → 2AlCl₃ + 3H₂Hydrogen given off
Iron oxide (thermite)Fe₂O₃ + 2Al → 2Fe + Al₂O₃ + heatAluminothermic process: Al is a strong reducing agent

Nitric acid does not dissolve aluminium; it makes the surface passive by forming an oxide film. Aluminium is light (density 2.7 g/cm³), silvery, malleable, ductile, a good conductor, and melts at 660 °C. It is used for utensils, electric cables and aircraft parts.

Copper

Copper occurs free (native) and in ores: copper pyrites (CuFeS₂, the chief ore), cuprite (Cu₂O) and copper glance (Cu₂S). It is extracted from copper pyrites in five stages.

Extracting copper from copper pyrites

  1. Concentration Crushed ore concentrated by froth floatation
  2. Roasting Heated in excess air: 2CuFeS₂ + O₂ → Cu₂S + 2FeS + SO₂
  3. Smelting With coke and sand in a blast furnace: gives matte (Cu₂S + FeS) and slag
  4. Bessemerisation FeS → FeO, removed as FeSiO₃ slag; 2Cu₂O + Cu₂S → 6Cu + SO₂ gives blister copper
  5. Electrolytic refining Impure copper anode, pure copper cathode, acidified CuSO₄ electrolyte

Worked example 2: atom check for the blister copper step

Question: Check 2Cu₂O + Cu₂S → 6Cu + SO₂.

Working: Cu: 2 × 2 + 2 = 6 on the left, 6 on the right. O: 2 on the left, 2 on the right. S: 1 and 1. Balanced. In electrolytic refining, pure copper builds up on the cathode and impurities fall below the anode as anode mud.

Copper is reddish brown, lustrous and dense; it melts at about 1085 °C. In moist air with carbon dioxide it gains a green coat of basic copper carbonate: 2Cu + O₂ + CO₂ + H₂O → CuCO₃·Cu(OH)₂. Heated in air it forms black CuO (below about 1370 K) or red Cu₂O (above it). It does not react with dilute HCl or H₂SO₄ unless air is present, and it is not attacked by alkalis. Uses: electric cables, utensils, coins, electroplating, and alloys with gold and silver for jewellery.

Iron

Iron is the second most abundant metal after aluminium. Its ores include haematite (Fe₂O₃, the chief ore), magnetite (Fe₃O₄) and iron pyrite (FeS₂). Haematite is concentrated by gravity separation, then roasted in a limited supply of air to drive off moisture and burn away sulphur, arsenic and phosphorus. Next it is smelted in a blast furnace with coke and limestone (the textbook gives the ratio 8 : 4 : 1).

Zones of the blast furnace (temperatures as given in the textbook)
ZoneTemperatureMain reactions
Lower: combustion zoneabout 1500 °CC + O₂ → CO₂ + heat (exothermic)
Middle: fusion zoneabout 1000 °CCO₂ + C → 2CO; CaCO₃ → CaO + CO₂ (both absorb heat); CaO + SiO₂ → CaSiO₃ (slag)
Upper: reduction zoneabout 400 °CFe₂O₃ + 3CO → 2Fe + 3CO₂

Molten iron collects at the bottom below the slag. This is pig iron; remelted and cast in moulds it is cast iron. Iron rusts in moist air (4Fe + 3O₂ + xH₂O → 2Fe₂O₃·xH₂O), forms magnetic oxide with steam (3Fe + 4H₂O → Fe₃O₄ + 4H₂), forms FeCl₃ with chlorine, and gives hydrogen with dilute HCl (Fe + 2HCl → FeCl₂ + H₂). Concentrated nitric acid makes it passive.

Types of iron (carbon ranges as given in the textbook)
TypeCarbon contentUses
Pig iron2.0-4.5%Pipes, stoves, radiators, railings, manhole covers
Steel0.25-2.0%Buildings, machinery, cables, towers, alloys
Wrought ironless than 0.25%Springs, anchors, electromagnets

Key takeaways: aluminium is made by Baeyer's process then electrolysis (Hall's process); copper by froth floatation, roasting, smelting, Bessemerisation and electrolytic refining; iron by reducing haematite with carbon monoxide in a blast furnace, with limestone removing silica as slag. Always check equations atom by atom.

Check your understanding

  1. 1. In Hall's process, why is cryolite added to alumina?

    1. To oxidise the aluminium
    2. To provide oxygen
    3. To dissolve alumina and lower the working temperature
    4. To make aluminium magnetic
    Show answer

    Answer: C. Alumina has a very high melting point. Dissolving it in molten cryolite (with fluorspar) lets electrolysis run at about 900-950 °C and improves conduction.

  2. 2. In the blast furnace, which substance actually reduces Fe₂O₃ to iron in the upper zone?

    1. Limestone
    2. Carbon monoxide
    3. Silica
    4. Oxygen
    Show answer

    Answer: B. Coke first burns to CO₂, which is reduced by more coke to CO. The CO then reduces the ore: Fe₂O₃ + 3CO → 2Fe + 3CO₂. Limestone forms the flux.

  3. 3. What is the slag formed in the extraction of iron?

    1. Calcium silicate, CaSiO₃
    2. Iron silicate, FeSiO₃
    3. Calcium carbonate, CaCO₃
    4. Iron oxide, Fe₃O₄
    Show answer

    Answer: A. Limestone decomposes to CaO, which combines with the silica gangue: CaO + SiO₂ → CaSiO₃. Iron silicate is the slag in copper extraction.

  4. 4. During electrolytic refining of copper, the impure copper is made the:

    1. Cathode
    2. Electrolyte
    3. Flux
    4. Anode
    Show answer

    Answer: D. Impure copper is the anode; it dissolves, and pure copper deposits on the thin pure-copper cathode. Impurities settle below the anode as anode mud.

  5. 5. How many molecules of CO are needed to reduce one formula unit of Fe₂O₃ to iron?

    1. 1
    2. 2
    3. 3
    4. 4
    Show answer

    Answer: C. Fe₂O₃ + 3CO → 2Fe + 3CO₂. Check: Fe 2 = 2; O: 3 + 3 = 6 on the left and 3 × 2 = 6 on the right; C: 3 = 3. So 3 molecules of CO are needed.

Sign in to keep track of the lessons you finish.

Next lesson → Alloys, amalgams and corrosion

Privacy · Terms · Refunds · Delivery