• Practice
  • About 16 min
  • 5 practice questions

Metallurgy basics: ores, concentration and properties of metals

Define the key terms of metallurgy, tell an ore from a mineral, choose the right method to concentrate an ore, and list the physical and chemical properties of metals.

If something looks wrong, please tell us.

By the end of this lesson you can

  • Name the three main steps of metallurgy.
  • Define mineral, ore, mining, gangue, flux, slag and smelting.
  • Match each concentration method to its principle and a suitable ore.
  • List typical physical and chemical properties of metals and their exceptions.

Metals are everywhere in daily life, from cooking vessels to electric wires, and some metals such as sodium, potassium, calcium and iron are also needed by the human body. Very few metals are found free in nature. Metallurgy is the science of extracting metals from their ores and turning them into useful forms such as alloys.

Three main steps of metallurgy

  1. Concentration of the ore Remove the unwanted rocky impurities
  2. Production of the metal Convert the concentrated ore into the metal, e.g. by reduction
  3. Refining Purify the crude metal

Key terms

TermMeaning
MineralA naturally occurring compound or mixture of compounds of a metal in the Earth
OreA mineral from which the metal can be extracted easily and profitably on a large scale
MiningTaking the ore out of the Earth's crust
Gangue (matrix)The rocky impurity that comes with the ore
FluxA substance added to remove gangue and lower the fusion temperature; basic flux (CaO) for acidic gangue, acidic flux (SiO₂) for basic gangue
SlagThe fusible product of flux + gangue, removed as waste
SmeltingReducing the roasted oxide to molten metal, with impurities removed as slag

All ores are minerals, but not all minerals are ores. Clay and bauxite both contain aluminium, but aluminium can be extracted profitably only from bauxite (Al₂O₃·2H₂O). So bauxite is an ore of aluminium, while clay is only a mineral of it.

Kinds of ores (examples from the textbook)
Oxide oresCarbonate oresHalide oresSulphide ores
Bauxite, Al₂O₃·2H₂OMarble, CaCO₃Cryolite, Na₃AlF₆Galena, PbS
Cuprite, Cu₂OMagnesite, MgCO₃Fluorspar, CaF₂Iron pyrite, FeS₂
Haematite, Fe₂O₃Siderite, FeCO₃Rock salt, NaClZinc blende, ZnS

Concentrating the ore

Methods of concentration

  • Hydraulic (gravity) separation
    • Principle: ore and gangue differ in density
    • Used when the ore is heavier
    • Water washes light gangue off a vibrating sloping table
    • Oxide ores, e.g. haematite
  • Magnetic separation
    • Principle: ore or gangue is magnetic
    • Magnetic roller on a conveyor pulls magnetic particles aside
    • e.g. tinstone, SnO₂
  • Froth floatation
    • Principle: ore is wetted by pine oil, gangue by water
    • Used when gangue is heavier
    • Air blown in; ore rises with the froth
    • Sulphide ores, e.g. zinc blende
  • Leaching (chemical method)
    • Ore dissolves in a reagent; impurities do not
    • Filter, then precipitate the ore back
    • e.g. bauxite

Worked example 1: choosing a method

Question: Which concentration method suits (a) galena, PbS, and (b) an iron ore that is strongly magnetic?

Working: (a) Galena is a sulphide ore, and sulphide ores are wetted by oil, so use froth floatation. (b) If the ore is magnetic and the gangue is not, a magnetic roller can pull it aside, so use magnetic separation.

Minerals in Tamil Nadu

According to the textbook (citing the ENVIS Centre, Tamil Nadu): limestone occurs in Coimbatore, Cuddalore and Dindigul; gypsum in Tiruchi and Coimbatore districts; titanium minerals in Kanyakumari, Tirunelveli and Thoothukudi; chromite in Coimbatore and Salem; magnetite in Dharmapuri, Erode, Salem and Tiruvannamalai; and tungsten in Madurai and Dindigul.

Properties of metals

Physical properties and the usual exceptions
PropertyUsual behaviourExceptions
StateSolid at room temperatureMercury is liquid; gallium melts just above room temperature
LustreShiny (metallic lustre)-
HardnessHard and strongSodium and potassium are soft enough to cut with a knife
Melting and boiling pointsHighGallium, mercury, sodium, potassium are low
DensityHighSodium and potassium float on water
Ductility and malleabilityDrawn into wires, beaten into sheetsZinc and mercury are not malleable at room temperature
ConductionGood conductors of heat and electricitySilver and copper are the best
  • Metal atoms usually have 1, 2 or 3 valence electrons.
  • They lose electrons to form positive ions, so they are electropositive.
  • During electrolysis, metal ions are discharged at the cathode.
  • Metal vapours are usually monoatomic.
  • Metal oxides are usually basic.

Worked example 2: reactivity decides the extraction method

Question: How is each of these obtained from its oxide: aluminium, zinc and mercury?

Working: Highly reactive metals (Na, K, Ca, Mg, Al) hold oxygen too strongly for carbon, so aluminium is made by electrolytic reduction. Medium-reactive metals (Zn, Fe, Pb, Cu) are reduced by coke (carbon), so zinc oxide is heated with coke. Low-reactivity metals (Ag, Hg) are obtained by simply heating the oxide (thermal decomposition), so mercury comes from heating its oxide.

Key takeaways: metallurgy = concentrate, extract, refine. An ore is a mineral that pays to process. Flux + gangue → slag. Choose gravity separation for heavy ores, magnetic separation for magnetic ones, froth floatation for sulphide ores, and leaching when the ore dissolves in a reagent. The more reactive the metal, the stronger the method needed to free it.

Check your understanding

  1. 1. Why is bauxite called an ore of aluminium but clay is not?

    1. Clay has no aluminium in it
    2. Bauxite is a liquid
    3. Aluminium can be extracted profitably only from bauxite
    4. Clay is found only in Tamil Nadu
    Show answer

    Answer: C. Both contain aluminium, so both are minerals. Only bauxite yields the metal easily and economically, so only bauxite is an ore.

  2. 2. Which method is used to concentrate zinc blende, ZnS?

    1. Froth floatation
    2. Magnetic separation
    3. Hydraulic washing
    4. Leaching
    Show answer

    Answer: A. Zinc blende is a sulphide ore. Sulphide ore particles are wetted by pine oil and carried up in the froth, while the gangue stays in the water.

  3. 3. The gangue in an ore is acidic (mainly silica). Which flux should be added?

    1. Silica, SiO₂
    2. Calcium oxide, CaO
    3. Sodium chloride, NaCl
    4. Pine oil
    Show answer

    Answer: B. An acidic gangue is removed by a basic flux. Calcium oxide is basic and combines with silica to form calcium silicate slag, CaSiO₃.

  4. 4. Which metal is a liquid at room temperature?

    1. Sodium
    2. Gallium
    3. Zinc
    4. Mercury
    Show answer

    Answer: D. Mercury is the only metal that is liquid at ordinary room temperature. Gallium melts at about 30 °C, a little above room temperature.

  5. 5. Hydraulic (gravity) separation works best when:

    1. The ore is heavier than the gangue
    2. The ore is magnetic
    3. The ore dissolves in alkali
    4. The ore is lighter than the gangue
    Show answer

    Answer: A. A stream of water washes away the lighter gangue while the denser ore particles settle in the grooves of the table. If the ore is lighter, froth floatation is used instead.

Privacy · Terms · Refunds · Delivery