• Practice
  • About 16 min
  • 5 practice questions

Contours: properties, contour interval and slope

State the properties of contours, find the contour interval, and judge and calculate slope from the spacing of contours.

If something looks wrong, please tell us.

By the end of this lesson you can

  • List the salient features of contours given in the textbook.
  • Find the contour interval of a map from contour values.
  • Judge slope from contour spacing and calculate a gradient.

Contours are the most useful way of showing relief because they give exact heights and still do not hide other features on the map. Reading them is a skill: with practice a set of brown lines turns into a picture of hills, valleys and slopes.

Salient features of contours

  1. Contours are drawn at regular intervals in brown. According to the textbook, generally a 20 m interval is used on 1 : 50,000 sheets and 100 m on 1 : 250,000 sheets.
  2. Every fifth contour is drawn thicker (an index contour) to make reading easier.
  3. The value of a contour is printed in a break in the line and also at the edge of the sheet.
  4. Contours generally never cut or cross each other. At a waterfall or cliff they almost meet at a point or line; only at an overhanging cliff do they cross.
  5. Closely spaced contours show a steep slope; widely spaced contours show a gentle slope; very widely spaced contours show nearly flat land.
  6. Heights are measured in metres above mean sea level.

Contour interval

The contour interval (CI) is the vertical difference in height between two neighbouring contours. It is usually printed in the margin; if not, find it from two labelled contours: CI = difference in their values ÷ number of gaps between them.

Contour interval = (difference between two labelled contours) ÷ (number of intervals between them).

Worked example 1: finding the contour interval

On a made-up sheet, a contour labelled 300 and another labelled 400 have four unlabelled contours between them. Step 1: lines from 300 to 400 inclusive = 1 + 4 + 1 = 6, so there are 5 gaps. Step 2: CI = (400 - 300) ÷ 5 = 20 m. The unlabelled contours are 320, 340, 360 and 380 m.

Slope and gradient

Spacing gives a quick judgement of slope; the gradient gives a number. Gradient = vertical rise ÷ horizontal distance, both in the same unit, usually written as 1 in n. The horizontal distance is measured on the map and converted with the scale.

Worked example 2: calculating a gradient

On a made-up 1 : 50,000 sheet, the 200 m and 300 m contours are 2 cm apart along a path. Step 1: horizontal distance = 2 × 50,000 cm = 100,000 cm = 1,000 m. Step 2: vertical rise = 300 - 200 = 100 m. Step 3: gradient = 100 ÷ 1,000 = 1/10, that is 1 in 10. Further along, the 300 m and 400 m contours are only 0.5 cm apart: horizontal distance = 0.5 × 50,000 = 25,000 cm = 250 m; gradient = 100 ÷ 250 = 1 in 2.5. The closer contours give the steeper slope, as the rule says.

What contour spacing tells you

  • Close together
    • Steep slope
    • Cliffs where they almost touch
    • Gorges in river courses
  • Evenly spaced
    • Uniform slope
    • Same gradient throughout
  • Far apart
    • Gentle slope
    • Plains when very wide
    • Flat plateau tops

Uniform, concave and convex slopes

If the spacing is equal, the slope is uniform. If contours are close near the top and wide near the bottom, the slope is concave (steep above, gentle below). If they are wide near the top and close near the bottom, the slope is convex (gentle above, steep below). Remember to check which end has the higher values before deciding.

Key takeaways: contours are brown lines of equal height above mean sea level, at a regular interval (generally 20 m on 1 : 50,000 sheets); every fifth one is thicker; they do not cross except at an overhanging cliff. Close spacing means steep, wide spacing means gentle. CI = difference ÷ gaps; gradient = rise ÷ horizontal distance.

Check your understanding

  1. 1. Contours on Survey of India sheets are printed in:

    1. blue
    2. brown
    3. black
    4. red
    Show answer

    Answer: B. The textbook states that contours are drawn in brown.

  2. 2. Between labelled contours of 100 m and 250 m there are two unlabelled contours. The contour interval is:

    1. 75 m
    2. 25 m
    3. 30 m
    4. 50 m
    Show answer

    Answer: D. There are 3 gaps (100 to 150, 150 to 200, 200 to 250). CI = 150 ÷ 3 = 50 m.

  3. 3. Where can contours cross one another?

    1. Only at an overhanging cliff
    2. On every hill
    3. In flat plains
    4. At river mouths
    Show answer

    Answer: A. Contours generally never cross; at a waterfall or cliff they almost meet, and they cross only at an overhanging cliff.

  4. 4. On a 1 : 50,000 map, two contours 50 m apart in height are 1 cm apart horizontally. The gradient is:

    1. 1 in 50
    2. 1 in 5
    3. 1 in 10
    4. 1 in 100
    Show answer

    Answer: C. Horizontal distance = 1 × 50,000 cm = 500 m. Gradient = 50 ÷ 500 = 1/10, that is 1 in 10.

  5. 5. Contours that are close together near the hilltop and far apart near the foot show a slope that is:

    1. uniform
    2. convex
    3. flat
    4. concave
    Show answer

    Answer: D. Steep at the top (close contours) and gentle at the bottom (wide contours) describes a concave slope.

Privacy · Terms · Refunds · Delivery