• Practice
  • About 16 min
  • 5 practice questions

Identifying landforms from contour patterns

Recognise hills, plateaus, ridges, cols and saddles, V-shaped valleys, spurs, waterfalls, cliffs, gorges and volcanoes from their contour patterns.

If something looks wrong, please tell us.

By the end of this lesson you can

  • Describe the contour pattern of each landform listed in the textbook.
  • Tell a valley from a spur by the direction in which the V points.
  • Find the height of a waterfall or cliff from the contours.

Each landform leaves a fingerprint in contours. Once you know the patterns, a topographical sheet tells you where the hills, valleys and waterfalls are without visiting the ground. The textbook gives these general instructions for identifying features.

Landforms and their contour patterns

Contour patterns of landforms
LandformContour pattern (textbook's description, in brief)
HillRoughly circular closed contours, values rising inwards; the textbook takes a hill as less than 1,000 m high.
PlateauAn elevated area whose innermost contour is wide and roughly rectangular, with outer contours close together (steep sides); the textbook gives a usual height of 300-600 m. Enclosed by mountains it is an intermontane plateau; at the foot of mountains, a piedmont plateau.
RidgeAn elongated, steep-sided high land with two or more peaks, shown by elliptical contours.
Col and saddleA col is a narrow, low depression between two peaks; a saddle is similar but higher, broader and more gently sloping.
V-shaped valleyContours bend sharply in a V across the river, with the apex pointing towards higher ground.
SpurA tongue of land from higher to lower ground; contours bend in a V with the apex pointing towards lower ground.
WaterfallContours meet at one point on the river course.
CliffA very steep slope of a valley side or coast (a sea cliff near the sea); contours run very close or merge.
GorgeA very steep, narrow valley at higher elevations; contours close together on both sides of the river.
VolcanoClosed contours whose innermost contours have lower values than those around them, showing the crater.

Valley or spur? Read the V

Valleys and spurs both make V-shaped contours, so students often confuse them. The trick is to see which way the V points. In a valley, the V points uphill (towards higher values), and a river usually flows along it, down the V. In a spur, the V points downhill (towards lower values). Both are common on the same hillside, alternating with each other.

Valley versus spur

  • V-shaped valley
    • Apex of V points to higher ground
    • River flows along the V
    • Formed by vertical erosion of the river
  • Spur
    • Apex of V points to lower ground
    • Projection of land between valleys
    • Contours bend smoothly

Valley: the V points up the hill. Spur: the V points down the hill.

Worked example 1: height of a waterfall

On a made-up sheet with CI 100 m, the contours 1,100, 1,200, 1,300 and 1,400 m all meet at one point on a river. Reasoning: the textbook says the height of a waterfall is the difference between the highest and the lowest contour touching the same point. Answer: 1,400 - 1,100 = 300 m. (If 1,000 m also touched the point, the drop would be 400 m.)

Worked example 2: hill, plateau or volcano?

Three made-up sets of closed contours. (a) 100, 200, 300, 400 m from outside in, innermost a small circle. (b) 100, 200, 300 m close together, then a broad, flat 400 m contour enclosing a wide rectangular area. (c) 100, 200, 300, 400 m from outside in, then a small inner ring of 300 m. Reasoning: values rising to a small top is a hill; steep sides and a broad level top is a plateau; values falling again inside the highest ring is a crater. Answer: (a) hill, (b) plateau, (c) volcano with a crater. If (c) were a hollow on flat land with no rise before it, it would be called a depression.

Other features shown by contours

  • Gentle slope: contours widely spaced; flat land: contours very widely spaced or absent.
  • Steep slope: contours close together.
  • Escarpment: a sudden drop in height at the edge of a plateau, contours crowded on one side.
  • Knoll: a small, low, rounded hill, often at the end of a spur.

Key takeaways: closed rising contours mean a hill; steep sides with a broad level top mean a plateau; elongated contours with several peaks mean a ridge, with a col or saddle between peaks; a V pointing uphill is a valley, downhill a spur; contours meeting on a river mark a waterfall (height = top minus bottom contour); converging contours mark cliffs and gorges; a lower inner ring marks a volcano's crater.

Check your understanding

  1. 1. Contours bend in a V with the apex pointing towards higher ground. This shows:

    1. a spur
    2. a V-shaped valley
    3. a plateau
    4. a knoll
    Show answer

    Answer: B. In a valley the V points upstream towards higher ground; in a spur it points towards lower ground.

  2. 2. Contours of 600, 700, 800 and 900 m meet at one point on a river. The height of the waterfall is:

    1. 300 m
    2. 900 m
    3. 100 m
    4. 400 m
    Show answer

    Answer: A. Height = highest - lowest contour touching the point = 900 - 600 = 300 m.

  3. 3. Closed contours with the innermost ring having a lower value than the ring around it show:

    1. a ridge
    2. a spur
    3. a gorge
    4. a volcano with a crater
    Show answer

    Answer: D. The textbook says a volcano is shown by closed contours whose innermost contours have lesser values, denoting the crater.

  4. 4. A narrow, low depression between two peaks of a ridge is called a:

    1. saddle
    2. knoll
    3. col
    4. spur
    Show answer

    Answer: C. The textbook defines a col as a narrow low depression between two peaks; a saddle is higher, broader and gentler.

  5. 5. Which contour pattern best represents a plateau?

    1. Close outer contours with a broad, roughly rectangular innermost contour
    2. Small circular contours rising to a point
    3. Contours meeting at a single point on a river
    4. A V pointing towards lower ground
    Show answer

    Answer: A. A plateau has steep sides (close outer contours) and a wide, fairly level top (broad innermost contour).

Sign in to keep track of the lessons you finish.

Next lesson → Drawing a cross section from contours

Privacy · Terms · Refunds · Delivery