• Practice
  • About 17 min
  • 5 practice questions

Drawing a cross section from contours

Follow the textbook's seven steps to draw a cross section along a line on a contour map, and use it to identify the landform and its slopes.

If something looks wrong, please tell us.

By the end of this lesson you can

  • List the steps for drawing a cross section from contours.
  • Draw a cross section from given distances and contour values.
  • Interpret the profile to name the landform and compare slopes.

A contour map shows the land from above. A cross section (profile) shows it from the side, as if the land were cut along a line and you looked at the cut face. It turns contour patterns into a shape you can see at once, which is why the textbook asks you to draw cross sections to identify landforms.

Steps in drawing a cross section

The textbook's method, in order:

  1. Draw the contours (in brown).
  2. Draw the line AB along which the section is required.
  3. Below the contours, draw as many horizontal lines as there are contour values, at an equal spacing (the textbook suggests 2 mm), to serve as a vertical scale.
  4. Write the contour values against these lines, with the lowest value as the base line and the values rising by the contour interval.
  5. From each point where AB crosses a contour, drop a vertical line to the horizontal line of the same value.
  6. Join all these points with a smooth curve to show the shape of the land.
  7. Shade the area below the curve in black to complete the section.

Cross section in brief

  1. Line AB Draw the section line on the contour map.
  2. Vertical scale Equal-spaced lines, one per contour value.
  3. Drop points From each crossing of AB and a contour, drop down to its value.
  4. Join and shade Join the points smoothly and shade below.

Profile points: where AB crosses a contour, drop a line to that contour's height. Join the points and the land appears.

Worked example 1: a single hill

Made-up data, CI 50 m. Along AB (12 cm long) the line crosses contours at these distances from A: 1 cm (100 m), 3 cm (150 m), 4 cm (200 m), 5 cm (250 m), 7 cm (250 m), 9 cm (200 m), 10.5 cm (150 m), 11.5 cm (100 m). Step 1: draw horizontal lines labelled 100, 150, 200, 250 m, 2 mm apart. Step 2: drop each crossing point to its line. Step 3: join them. Reading the profile: the land rises from 100 m to a summit above 250 m between 5 cm and 7 cm, then falls again, so it is a hill. Compare the sides: on the A side the 100 m to 250 m rise is spread over 4 cm; on the B side it falls over 4.5 cm, so the B side is slightly gentler. The 2 cm stretch between the two 250 m crossings is the hill-top, which lies above 250 m but below 300 m.

Worked example 2: a valley

Made-up data, CI 100 m, along a 10 cm line: 0.5 cm (500 m), 1.5 cm (400 m), 2.5 cm (300 m), 4 cm (200 m), 6 cm (200 m), 7 cm (300 m), 8 cm (400 m), 9 cm (500 m). Step 1: plot as before. Step 2: the curve falls from 500 m to below 200 m in the middle and rises again. Reading: a valley, with the river in the lowest part between 4 cm and 6 cm. The fall from 500 to 200 m takes 3.5 cm on the left; the rise from 200 to 500 m takes 3 cm on the right, so the right side is steeper. A narrow, steep-sided profile like this matches a V-shaped valley.

Checks before you finish

  • Every crossing of AB with a contour must have a point; count them on the map and on the section.
  • Hilltops and valley floors lie between contour values: draw the top slightly above the highest contour, never flat at it, and a valley floor slightly below the lowest.
  • Write the vertical scale and the contour interval, and mark A and B at the ends of the section.

Key takeaways: a cross section shows the land in side view along a line AB. Use equally spaced horizontal lines for the contour values, drop a point from each crossing to its value, join smoothly and shade. Steep parts show as rapid rises over short distances; the shape reveals hills, valleys, plateaus and cliffs.

Check your understanding

  1. 1. In drawing a cross section, the base line represents:

    1. the highest contour value
    2. the lowest contour value
    3. mean sea level always
    4. the line AB
    Show answer

    Answer: B. The textbook says to write the contour values so that the lowest value forms the base line and values increase by the contour interval.

  2. 2. Along AB, the land rises from 100 m to 400 m in 2 cm on the left and falls from 400 m to 100 m in 6 cm on the right. Which side is steeper?

    1. The right side
    2. Both are equal
    3. The left side
    4. It cannot be told
    Show answer

    Answer: C. The same 300 m change happens over a shorter distance (2 cm) on the left, so the left side is steeper.

  3. 3. A section line crosses contours 200, 300, 400, 300, 200 in that order. The landform is most likely a:

    1. valley
    2. plain
    3. waterfall
    4. hill or ridge
    Show answer

    Answer: D. Values rise to a top and fall again, which is the profile of a hill (or a ridge, if the contours are elongated).

  4. 4. From each point where AB crosses a contour, you should:

    1. drop a vertical line to the horizontal line of the same value
    2. draw a circle
    3. measure the angle of slope with a protractor
    4. write the name of the landform
    Show answer

    Answer: A. This is step 5 of the textbook's method; the dropped points are then joined to form the profile.

  5. 5. A section shows 500, 400, 300, 300, 400, 500 m. Where is the lowest land?

    1. At both ends
    2. Between the two 300 m crossings, below 300 m
    3. At the 500 m points
    4. Exactly at 300 m everywhere
    Show answer

    Answer: B. Values fall to 300 m and rise again, so the floor between the two 300 m crossings lies a little below 300 m: a valley.

Sign in to keep track of the lessons you finish.

Next lesson → Climatic diagrams and the wind rose

Privacy · Terms · Refunds · Delivery