Revision notes

Unit 9 Map and Scale: Foundation

The key points, rules to remember, tables and diagrams from all 5 lessons, on one page for quick revision. To keep a copy, use your browser's Print and choose "Save as PDF".

Lesson 1

What a map is and the components of a map

Components of a map and their conventional positions (as described in the textbook)
ComponentWhat it doesUsual position
TitleTells what the map is about: area, subject and, where needed, the date.Top centre, or sometimes bottom centre.
ScaleGives the ratio between distances on the map and on the ground.A prominent place: just below the title or at the bottom.
Legend (key)Explains the signs, symbols and colours used.Bottom left or bottom right corner.
DirectionShows north; by convention the top of the map is north, shown by an upward arrow (or a compass rose).Top right corner.
SourceNames where the data came from.Outside the map frame, bottom right.
Author and publication detailsAuthor, publisher, place and year of publication.Bottom left, outside the frame.
Latitude and longitudeGives the extent of the area mapped.Marked along the edges of the frame.

A complete map

  • Tells WHAT Title
    • Area, subject, date
  • Tells HOW BIG Scale
    • Statement, RF or bar scale
  • Tells WHAT SYMBOLS MEAN Legend
    • Signs, symbols, colours
  • Tells WHICH WAY Direction
    • North arrow or compass rose
  • Tells FROM WHERE Source and extent
    • Data source
    • Latitude and longitude

TSLDS: Title, Scale, Legend, Direction, Source. A map without these is a picture, not a map.

Key takeaways: a map is a scaled representation of the earth or part of it on a flat surface. Its basic components are title, scale, legend, direction and source, together with the latitude-longitude extent. By convention north is at the top, shown by an arrow at the top right; the legend sits at a bottom corner and the source outside the frame at the bottom right.

Read the full lesson

Lesson 2

Scale: meaning and the three ways of showing it

Scale = map distance ÷ ground distance (both in the same unit).

Three ways of showing scale

  • Statement
    • In words: 1 cm represents 5 km
    • Easiest to understand
    • Tied to one unit system
    • Wrong after enlargement or reduction
  • Representative fraction
    • Ratio: 1 : 500,000
    • No units, works in any system
    • Needs calculation to read
    • Wrong after enlargement or reduction
  • Bar scale
    • A divided line
    • Read distances directly
    • Stays correct when the map is enlarged or reduced
    • Needs care to construct

Key takeaways: scale is the ratio of map distance to ground distance. It may be shown as a statement (in words), as an RF (a unitless ratio such as 1 : 50,000) or as a bar scale (a divided line). The RF works in any unit system; the bar scale stays correct when the map is enlarged or reduced. A larger denominator means a smaller scale.

Read the full lesson

Lesson 3

Converting scales and constructing a bar scale

Units needed for scale conversion
UnitEquals
1 km1,000 m = 100,000 cm
1 m100 cm
1 mile63,360 inches

Statement to RF: bring both sides to the same unit, then divide so the map side becomes 1. RF to statement: divide the denominator by 100,000 (cm to km) or 63,360 (inches to miles).

Steps to draw a bar scale

  1. Find ground per cm From the RF, work out what 1 cm represents.
  2. Choose a round length Pick a round ground distance whose line is close to 15 cm.
  3. Draw and divide Draw the line and mark equal primary divisions.
  4. Place zero Write 0 at the end of the first division; number primaries to the right.
  5. Secondary divisions Divide the left division into smaller units, numbered leftwards from 0.
  6. Label Write the units and the RF below the scale.

Key takeaways: for any conversion, bring both sides to the same unit (1 km = 100,000 cm; 1 mile = 63,360 inches) and reduce the map side to 1. A bar scale is drawn about 15 cm long for a round ground distance, divided into primary divisions with 0 after the first, and the first division split into secondary units.

Read the full lesson

Lesson 4

Measuring distance and area on a map

Measuring a winding river on a map

  1. Lay the thread Hold one end at the start point.
  2. Follow every bend Press the thread along the curve to the end point; mark it.
  3. Straighten and measure Stretch the thread along a ruler and read the length in cm.
  4. Apply the scale Multiply by the ground distance represented by 1 cm.

Area of one square on the ground = (ground distance of its side)². If 1 cm represents 2 km, a 1 cm square represents 2 × 2 = 4 km², not 2 km².

Key takeaways: measure straight features with dividers or a ruler, and winding features with a thread or a rotameter; then multiply by the scale. For area, count full and part squares, convert to full-square equivalents, and multiply by the ground area of one square, which is the square of its side's ground length.

Read the full lesson

Lesson 5

Enlarging and reducing maps by the square method

Side of new square = side of old square × (new RF ÷ old RF). Area changes by the square of the scale factor.

Enlarging or reducing a map by similar squares

  1. Draw squares on the original Cover the map with a network of equal squares, for example 1 cm.
  2. Calculate the new side New side = old side × (new RF ÷ old RF).
  3. Draw the new network Draw the same number of squares with the new side.
  4. Number rows and columns Label both networks alike so squares can be matched.
  5. Transfer the outline Copy what lies in each original square into the matching new square.
  6. Finish Ink the outline, add title, new scale and north arrow.

Key takeaways: enlargement and reduction keep the shape and change size by a constant scale factor. Area changes by the square of that factor. New square side = old side × old RF denominator ÷ new RF denominator. Each square must represent the same ground distance on both maps.

Read the full lesson

Privacy · Terms · Refunds · Delivery