• Practice
  • About 24 min
  • 5 practice questions

Angular SHM, spring-mass oscillators and combinations of springs

Find the period of angular SHM, of a mass on a horizontal or vertical spring, and of springs joined in series and in parallel, including a spring cut into pieces.

If something looks wrong, please tell us.

By the end of this lesson you can

  • Derive ω = √(κ/I) and T = 2π√(I/κ) for angular SHM, and compare it with linear SHM.
  • Derive T = 2π√(m/k) for horizontal and vertical spring-mass oscillators, and T = 2π√(l/g) for a hanging mass.
  • Find the effective spring constant for springs in series and in parallel.
  • Find the spring constants of the pieces of a cut spring.

Lessons 1 and 2 described SHM. Now we look at real systems that perform it: a disc twisting on a wire, and blocks on springs. In each case we find the restoring force or torque, write Newton's second law in the form of the SHM equation and read off ω.

Angular simple harmonic motion

A disc hung from a fibre can twist about the fibre as an axis. At the mean position the resultant torque is zero. Twisted through an angle θ, the fibre exerts a restoring torque proportional to θ: τ = −κθ, where κ (kappa) is the restoring torsion constant, the torque per unit angular displacement. With moment of inertia I, τ = Iα = I d²θ/dt², so d²θ/dt² = −(κ/I)θ. Comparing with the SHM equation:

Angular SHM: ω = √(κ/I), f = (1/2π)√(κ/I), T = 2π√(I/κ)

Comparison of linear and angular SHM
Linear SHMAngular SHM
Linear displacement rAngular displacement θ (angle of twist)
Acceleration a = −ω²rAngular acceleration α = −ω²θ
F = ma (inertia factor: mass m)τ = Iα (inertia factor: moment of inertia I)
Restoring force F = −krRestoring torque τ = −κθ
ω = √(k/m)ω = √(κ/I)

A horizontal spring-mass system

A block of mass m on a smooth horizontal surface is fixed to a massless spring of spring constant k. Pulled a small distance x from its equilibrium position and released, the spring exerts F = −kx (Hooke's law). This holds only while the force is linear in x; very large stretches give non-linear oscillations, which we do not consider. Newton's second law gives m d²x/dt² = −kx, or d²x/dt² = −(k/m)x. So the natural angular frequency is ω = √(k/m), with f = (1/2π)√(k/m) and T = 2π√(m/k). The general solution is x(t) = A sin(ωt + φ) (or a cosine), and the period does not depend on the amplitude as long as the oscillations are small.

A useful way to remember it: T = 2π√(inertial property / elastic property) = 2π√(displacement / acceleration), since |x/(d²x/dt²)| = m/k.

A vertical spring

Hang a mass m from a spring fixed to a ceiling. The spring stretches by l until the spring force balances the weight: kl = mg, so m/k = l/g. Pull the mass down a further distance y. The spring force is now −k(y + l), and the net force is −ky − kl + mg = −ky, because kl = mg. Again m d²y/dt² = −ky, so the period is the same as for horizontal oscillations: T = 2π√(m/k) = 2π√(l/g). This also gives a way to measure g: g = 4π²l/T².

Springs in series and in parallel

A stiffer spring has a larger k. The reciprocal 1/k is called the flexibility constant or compliance, measured in m N⁻¹.

Series (end to end). The same force F acts through both springs, but each stretches differently: x₁ = F/k₁, x₂ = F/k₂. The total stretch is x = x₁ + x₂ = F/kₛ. So F/kₛ = F/k₁ + F/k₂, giving 1/kₛ = 1/k₁ + 1/k₂, or kₛ = k₁k₂/(k₁ + k₂). For n identical springs, kₛ = k/n. The combination is softer than either spring. Since k₁x₁ = k₂x₂, the stretches are in the ratio x₁ : x₂ = k₂ : k₁, and the stored energies ½kx² are in the ratio U₁ : U₂ = k₂ : k₁: the softer spring stretches more and stores more energy.

Parallel (side by side). Both springs stretch by the same x, and their forces add: F = k₁x + k₂x = kₚx. So kₚ = k₁ + k₂, and for n identical springs kₚ = nk. The combination is stiffer than either spring. Spring sets in motorcycle shock absorbers combine springs in this way.

Springs in series and in parallel

  • Series
    • Same force in each spring
    • Stretches add: x = x₁ + x₂
    • 1/kₛ = 1/k₁ + 1/k₂
    • Softer than the softest spring; n equal springs: k/n
  • Parallel
    • Same stretch in each spring
    • Forces add: F = F₁ + F₂
    • kₚ = k₁ + k₂
    • Stiffer than the stiffest spring; n equal springs: nk

Cutting a spring. The spring constant is inversely proportional to the length of a spring. If a spring of constant k is cut into two pieces with l₁ = n l₂, the pieces have k₁ = k(n + 1)/n and k₂ = (n + 1)k. A spring cut into two equal halves (n = 1) gives two springs of constant 2k each.

Worked example 1: a block on a spring

A 0.50 kg block on a smooth table is attached to a spring of constant 200 N m⁻¹. Find ω, T and f. Step 1: ω = √(k/m) = √(200/0.50) = √400 = 20 rad s⁻¹. Step 2: T = 2π/ω = 2π/20 ≈ 0.314 s. Step 3: f = 1/T ≈ 3.18 Hz.

Worked example 2: period from the stretch

A load hung on a spring stretches it by 4.0 cm. Find the period of small vertical oscillations (g = 9.8 m s⁻²). Step 1: T = 2π√(l/g) with l = 0.040 m. Step 2: l/g = 0.040/9.8 = 4.08 × 10⁻³ s². Step 3: √(4.08 × 10⁻³) ≈ 0.0639 s, and T = 2π × 0.0639 ≈ 0.40 s. The mass and the spring constant were not needed separately.

Worked example 3: series and parallel

Springs of constants 300 N m⁻¹ and 600 N m⁻¹ are joined (a) in series and (b) in parallel, and the same mass is hung from each combination. Find the effective constants and the ratio of the periods. (a) kₛ = (300 × 600)/(300 + 600) = 180000/900 = 200 N m⁻¹. (b) kₚ = 300 + 600 = 900 N m⁻¹. (c) T ∝ 1/√k, so Tₛ/Tₚ = √(kₚ/kₛ) = √(900/200) = √4.5 ≈ 2.1. The series arrangement oscillates about twice as slowly.

Worked example 4: a torsion pendulum and a cut spring

(a) A disc of moment of inertia 2.0 × 10⁻³ kg m² hangs from a wire of torsion constant 8.0 × 10⁻² N m rad⁻¹. T = 2π√(I/κ) = 2π√(2.0 × 10⁻³ / 8.0 × 10⁻²) = 2π√0.025 = 2π × 0.158 ≈ 0.99 s. (b) A spring of constant 120 N m⁻¹ is cut so that one piece is twice as long as the other (n = 2). Then k₁ = 120 × 3/2 = 180 N m⁻¹ and k₂ = 3 × 120 = 360 N m⁻¹. Check: the two in series give (180 × 360)/(180 + 360) = 64800/540 = 120 N m⁻¹, the original spring.

Key takeaways

  • Angular SHM: τ = −κθ, T = 2π√(I/κ).
  • Spring-mass system, horizontal or vertical: T = 2π√(m/k); hanging mass: T = 2π√(l/g).
  • Series: 1/kₛ = Σ 1/kᵢ (softer); parallel: kₚ = Σ kᵢ (stiffer).
  • k ∝ 1/length: half a spring is twice as stiff.

Check your understanding

  1. 1. A 2.0 kg mass oscillates on a spring of constant 50 N m⁻¹. Its time period is about:

    1. 0.20 s
    2. 1.26 s
    3. 0.80 s
    4. 5.0 s
    Show answer

    Answer: B. T = 2π√(m/k) = 2π√(2.0/50) = 2π√0.04 = 2π × 0.2 ≈ 1.26 s. The value 0.20 s is √(m/k) without the 2π.

  2. 2. Two identical springs, each of constant k, are joined in series. The effective spring constant is:

    1. 2k
    2. k
    3. k/2
    4. k²
    Show answer

    Answer: C. 1/kₛ = 1/k + 1/k = 2/k, so kₛ = k/2. Joining springs end to end makes the combination softer.

  3. 3. A spring of constant k is cut into three equal pieces, and the three pieces are joined in parallel to hold a mass. Compared with the period T of the mass on the whole spring, the new period is:

    1. T/3
    2. T/√3
    3. 3T
    4. T
    Show answer

    Answer: A. Each one-third piece has constant 3k (k ∝ 1/length). Three in parallel: 3k + 3k + 3k = 9k. T ∝ 1/√k, so T′ = T/√9 = T/3.

  4. 4. A mass hung on a spring stretches it by 9.8 cm. Taking g = 9.8 m s⁻², the period of its vertical oscillations is about:

    1. 0.20 s
    2. 0.10 s
    3. 2.0 s
    4. 0.63 s
    Show answer

    Answer: D. T = 2π√(l/g) = 2π√(0.098/9.8) = 2π√0.01 = 2π × 0.1 ≈ 0.63 s. The value 0.10 s leaves out the 2π.

  5. 5. In angular SHM, the quantity that plays the role of the mass m of linear SHM is:

    1. the torsion constant κ
    2. the angular displacement θ
    3. the torque τ
    4. the moment of inertia I
    Show answer

    Answer: D. In τ = Iα, the moment of inertia is the inertia factor, just as m is in F = ma. The torsion constant κ plays the role of the spring constant k.

Privacy · Terms · Refunds · Delivery