Revision notes

Unit 3 Laws of Motion: Foundation

The key points, rules to remember, tables and diagrams from all 5 lessons, on one page for quick revision. To keep a copy, use your browser's Print and choose "Save as PDF".

Lesson 1

From Aristotle to Newton: inertia, frames and the three laws

Two views of force

  • Aristotle
    • Force is needed to keep a body moving
    • Constant velocity needs a constant push
    • Friction was not considered
  • Galileo and Newton
    • Force is needed only to change motion
    • Constant velocity means zero net force
    • The push balances friction

First law: every object continues in its state of rest or of uniform motion (constant velocity) unless an external force acts on it.

Second law: the force on an object equals the rate of change of its momentum, F = dp/dt. For constant mass, F = d(mv)/dt = m dv/dt = ma.

Third law: for every action there is an equal and opposite reaction. If body 1 exerts F₂₁ on body 2, body 2 exerts F₁₂ = −F₂₁ on body 1, along the line joining them.

  • Galileo showed that force is needed to change motion, not to maintain it.
  • First law: no external force, no change in velocity; inertia is the resistance to that change.
  • The first and second laws hold only in inertial frames; the Earth is nearly inertial for everyday motion.
  • Second law: F = dp/dt = ma, a vector law that acts at each instant.
  • Third law: action and reaction are equal, opposite, simultaneous and act on different bodies.
Read the full lesson

Lesson 2

Applying Newton's laws: free body diagrams, inclines and connected bodies

Steps for a Newton's law problem

  1. Choose an inertial frame and axes Usually the ground; tilt the axes along an incline if the motion is along it.
  2. Choose the system One body or several bodies taken together.
  3. Draw the free body diagram Only forces acting ON the system, never forces it exerts on others.
  4. Apply F_net = ma along each axis Compare components on both sides.
  5. Solve Find the force if a is known, or a if the forces are known.

Masses over a pulley: a = (m₁ − m₂)g/(m₁ + m₂), T = 2m₁m₂g/(m₁ + m₂). One on a smooth table: a = m₁g/(m₁ + m₂), T = m₁m₂g/(m₁ + m₂).

  • A free body diagram shows only forces acting on the chosen body or system.
  • Internal forces cancel within a system; only external forces accelerate it.
  • Smooth incline: N = mg cos θ, a = g sin θ, v = √(2gs sin θ).
  • Blocks in contact: a = F/(m₁ + m₂); the contact force is the pushed mass × a.
  • Pulley: a = (m₁ − m₂)g/(m₁ + m₂); the horizontal-table tension is half the vertical one.
Read the full lesson

Lesson 3

Lami's theorem, conservation of momentum and impulse

Lami's theorem: if three concurrent, coplanar forces F₁, F₂, F₃ keep a body in equilibrium, each force is proportional to the sine of the angle between the other two: F₁/sin α = F₂/sin β = F₃/sin γ, where α is the angle between F₂ and F₃, β between F₃ and F₁, and γ between F₁ and F₂.

If no external force acts on a system, its total linear momentum is a constant vector: p₁ + p₂ + ... is conserved in magnitude and direction.

Making the stopping time longer to reduce the force

  • Catching a ball The fielder draws the hands back with the ball.
  • Air bags in cars Passengers' momentum falls more slowly in a crash.
  • Shock absorbers A bump's force reaches the rider over a longer time.
  • Jumping on sand Sand stops the body more slowly than concrete.
  • Lami: F₁/sin α = F₂/sin β = F₃/sin γ for three concurrent forces in equilibrium.
  • With no external force, the total momentum of a system is conserved; internal forces cannot change it.
  • Recoil: MV = −mv, so the gun moves back with momentum equal to the bullet's.
  • Impulse J = ∫F dt = Δp, unit N s; it is the area under the F-t graph.
  • F_avg = Δp/Δt: a longer stopping time means a smaller force.
Read the full lesson

Lesson 4

Friction: static and kinetic friction, angle of repose and rolling

Static and kinetic friction compared
Static frictionKinetic friction
Opposes the start of motionOpposes relative motion while sliding
Adjusts from zero up to μsNFixed at μkN, never zero while sliding
Equals the applied force until sliding startsIndependent of the applied force
Maximum value greater than kinetic frictionLess than the maximum static friction
Independent of area of contactIndependent of area of contact

μs = tan(angle of friction) = tan(angle of repose); on a rough incline a body slides with a = g(sin θ − μk cos θ).

  • Static friction adjusts: 0 ≤ f_s ≤ μsN; kinetic friction is f_k = μkN, with μk < μs.
  • Friction is independent of the area of contact.
  • Pulling at an angle reduces N, so it is easier than pushing.
  • μs = tan θ for both the angle of friction and the angle of repose.
  • Rolling friction is far smaller than sliding friction; lubricants and ball bearings reduce friction.
Read the full lesson

Lesson 5

Dynamics of circular motion: centripetal force, banking and centrifugal force

Level road: v_max = √(μs r g). Banked road (no friction): v = √(r g tan θ), or tan θ = v²/(rg).

Centripetal and centrifugal forces compared
Centripetal forceCentrifugal force
Real force supplied by tension, gravity, friction, normal force and so onPseudo (fictitious) force with no interaction behind it
Acts in inertial and non-inertial framesAppears only in rotating (non-inertial) frames
Directed towards the centre or axisDirected away from the centre or axis
Magnitude mv²/r = mω²rMagnitude mω²r = mv²/r
Origin: interaction between bodiesOrigin: inertia of the body, seen from a rotating frame
  • Circular motion always needs a net inward force F_cp = mv²/r = mω²r, supplied by a real force.
  • Level road: friction supplies the centripetal force, safe if v ≤ √(μs r g).
  • Banked road: N sin θ supplies it, giving the safe speed √(r g tan θ).
  • Centrifugal force mω²r is a pseudo force that appears only in rotating frames, with real effects.
  • On the rotating Earth the centrifugal force is mω²R cos λ: tiny compared with weight, largest at the equator.
Read the full lesson

Privacy · Terms · Refunds · Delivery