- Practice
- About 26 min
- 5 practice questions
Friction: static and kinetic friction, angle of repose and rolling
Explain static and kinetic friction and their laws, decide whether a body moves, show why pulling is easier than pushing, relate the angle of friction and the angle of repose to μs, and describe rolling friction and ways to reduce friction.
If something looks wrong, please tell us.
By the end of this lesson you can
- State that static friction adjusts from 0 up to μsN and that kinetic friction is μkN with μk < μs.
- Decide whether a body moves under an applied force and find its acceleration if it does.
- Show with free body diagrams that pulling at an angle is easier than pushing.
- Prove that μs = tan θ for both the angle of friction and the angle of repose.
- Explain rolling friction, lubricants and ball bearings, and the origin of friction.
Push a heavy almirah gently and it does not move; push harder and it suddenly starts to slide, after which it is a little easier to keep it moving. Friction explains all three observations. It opposes the relative motion between surfaces, always acts parallel to the surface, and comes in two main kinds: static and kinetic.
Static friction
When a body is at rest and a force F_ext parallel to the surface is applied, the surface exerts an equal and opposite static friction f_s, so the body stays at rest. As F_ext increases, f_s increases with it, up to a maximum. Beyond that maximum the surface cannot match the applied force and the body starts to slide. Experimentally, 0 ≤ f_s ≤ μsN, where μs is the coefficient of static friction (depending on the two materials) and N is the normal force. N often equals mg, but not always. Friction does not depend on the area of contact. Note that f_s = μsN is a relation between magnitudes only, since friction and the normal force are perpendicular.
Kinetic friction
Once the body slides, the surface exerts kinetic (sliding) friction f_k = μkN, with μk < μs: starting motion is harder than maintaining it. Kinetic friction does not depend on the applied force and, for ordinary speeds (the textbook says below about 10 m s⁻¹), not on the speed. To keep a body moving at constant velocity, the applied force must just equal μkN; the net force is then zero, though two forces act.
| Static friction | Kinetic friction |
|---|---|
| Opposes the start of motion | Opposes relative motion while sliding |
| Adjusts from zero up to μsN | Fixed at μkN, never zero while sliding |
| Equals the applied force until sliding starts | Independent of the applied force |
| Maximum value greater than kinetic friction | Less than the maximum static friction |
| Independent of area of contact | Independent of area of contact |
The textbook lists typical coefficients of static friction: about 0.10 for ice on ice, 0.35 for wood on wood, 0.75 for steel on steel, 0.7 for a tyre on a wet road and 1.0 for a tyre on dry concrete and for glass on glass.
Worked example 1: will it move?
A 5 kg box rests on a floor with μs = 0.4 and μk = 0.3 (g = 9.8 m s⁻²). N = 5 × 9.8 = 49 N. Maximum static friction = 0.4 × 49 = 19.6 N. (a) A push of 15 N: the box does not move and friction is 15 N, not 19.6 N. (b) It starts to slide only when the push exceeds 19.6 N. (c) Once sliding, f_k = 0.3 × 49 = 14.7 N; with a 25 N push, a = (25 − 14.7)/5 = 10.3/5 ≈ 2.06 m s⁻². (d) An 8 kg block on a table (μs = 0.5) is tied over a pulley to a hanging 3 kg mass. Maximum static friction = 0.5 × 8 × 9.8 = 39.2 N, but the pull is only 3 × 9.8 = 29.4 N, so the block stays put; a hanging mass of more than 0.5 × 8 = 4 kg is needed to start it.
Push or pull?
Let a force F act at an angle θ to the horizontal on a block of mass m. Its horizontal part is F cos θ and its vertical part F sin θ. Pushing (force directed downwards into the floor) presses the block harder: N_push = mg + F sin θ, so the maximum friction μs(mg + F sin θ) is larger. Pulling (force directed upwards) lifts it a little: N_pull = mg − F sin θ, so the maximum friction μs(mg − F sin θ) is smaller. Hence it is easier to pull than to push. (The Tamil Nadu textbook measures the angle from the vertical, which swaps sin and cos; the conclusion is the same.)
Worked example 2: pushing versus pulling a trunk
A 10 kg trunk (μs = 0.5, g = 9.8 m s⁻²) is acted on by 50 N at 30° to the horizontal. Horizontal part = 50 cos 30° = 43.3 N; vertical part = 50 sin 30° = 25 N. Push: N = 98 + 25 = 123 N, maximum friction = 61.5 N > 43.3 N, so the trunk does not move. Pull: N = 98 − 25 = 73 N, maximum friction = 36.5 N < 43.3 N, so the trunk moves.
Angle of friction and angle of repose
The angle of friction is the angle between the normal force N and the resultant R of N and the maximum static friction. Since tan θ = f_s(max)/N and f_s(max) = μsN, μs = tan θ. The angle of repose is the angle of an incline at which a body placed on it just begins to slide. At that angle, mg sin θ = f_s(max) = μs mg cos θ, so again μs = tan θ. The two angles are equal; the angle of repose refers to an inclined surface, while the angle of friction applies to any surface.
μs = tan(angle of friction) = tan(angle of repose); on a rough incline a body slides with a = g(sin θ − μk cos θ).
Applications: antlions build sand pits with sides at the angle of repose, so an insect that steps on the edge slides to the bottom. A playground slide must be steeper than the angle of repose, but not so steep that children reach the bottom too fast. Activity (safe): put a coin on the cover of a hard-bound notebook and slowly raise the cover. Measure the angle at which the coin starts to slide; its tangent is μs. Lower the cover a little until the coin slides at steady speed; the tangent of that smaller angle is μk.
Worked example 3: on a rough slope
(a) A block starts to slide when a plank is tilted to 31°: μs = tan 31° ≈ 0.60. (b) A block slides down a 30° incline with μk = 0.2 (g = 9.8 m s⁻²). Along the slope, mg sin θ − μk mg cos θ = ma, so a = 9.8 × (0.5 − 0.2 × 0.866) = 9.8 × (0.5 − 0.173) = 9.8 × 0.327 ≈ 3.2 m s⁻², compared with 4.9 m s⁻² on a smooth incline.
Rolling friction and reducing friction
In pure rolling, the point of the wheel touching the ground is momentarily at rest, so there is no sliding and hardly any friction; in practice the wheel and the surface deform slightly at the contact, giving a small rolling friction, much smaller than kinetic friction. That is why wheeled suitcases are easy to move. Friction is useful (walking, tyres gripping the road, brakes), but in machines it wastes energy as heat and causes wear. It is reduced by lubricants (oil fills the gaps between rough surfaces) and ball bearings (sliding is replaced by rolling). Friction is not a separate fundamental force: it is the electromagnetic attraction between atoms at the tiny points where two surfaces, rough even when polished, actually touch. On a bicycle being pedalled, static friction on the rear wheel acts forwards and on the front wheel backwards.
Key takeaways
- Static friction adjusts: 0 ≤ f_s ≤ μsN; kinetic friction is f_k = μkN, with μk < μs.
- Friction is independent of the area of contact.
- Pulling at an angle reduces N, so it is easier than pushing.
- μs = tan θ for both the angle of friction and the angle of repose.
- Rolling friction is far smaller than sliding friction; lubricants and ball bearings reduce friction.
Check your understanding
-
1. A 20 kg block rests on a floor (μs = 0.5, g = 10 m s⁻²). A horizontal force of 60 N is applied. The friction acting on the block is:
- 100 N
- 60 N
- 40 N
- zero
Show answer
Answer: B. Maximum static friction = 0.5 × 20 × 10 = 100 N. Since 60 N < 100 N, the block stays at rest and static friction adjusts to exactly 60 N, opposite to the applied force.
-
2. A coin on a tilted book starts to slide when the angle is 45°. The coefficient of static friction is:
- 0.5
- 0.71
- 1.41
- 1.0
Show answer
Answer: D. At the angle of repose μs = tan θ = tan 45° = 1.0.
-
3. Pulling a box with a rope at an angle above the horizontal is easier than pushing it at the same angle below the horizontal because pulling:
- reduces the normal force and so the friction
- increases the normal force
- removes friction altogether
- increases the mass of the box
Show answer
Answer: A. The upward part of a pull reduces N to mg − F sin θ; the downward part of a push increases it to mg + F sin θ. Maximum friction μsN is therefore smaller when pulling.
-
4. Which statement about kinetic friction is correct?
- It increases with the applied force
- It is greater than the maximum static friction
- It is less than the maximum static friction
- It depends on the area of contact
Show answer
Answer: C. Kinetic friction μkN is fixed, independent of the applied force and area of contact, and less than the maximum static friction because μk < μs.
-
5. A block slides down a 37° incline with μk = 0.25 (take sin 37° = 0.6, cos 37° = 0.8, g = 10 m s⁻²). Its acceleration is:
- 6 m s⁻²
- 8 m s⁻²
- 2 m s⁻²
- 4 m s⁻²
Show answer
Answer: D. a = g(sin θ − μk cos θ) = 10 × (0.6 − 0.25 × 0.8) = 10 × (0.6 − 0.2) = 4 m s⁻².
Sign in to keep track of the lessons you finish.