• Practice
  • About 16 min
  • 5 practice questions

Bearings and plotting a compass traverse

Explain magnetic bearings measured clockwise from magnetic north, calculate back bearings, use them to check for errors, and plot an open or closed compass traverse from bearings and distances.

If something looks wrong, please tell us.

By the end of this lesson you can

  • Define a magnetic bearing and read it as a whole-circle bearing from 0° to 360°.
  • Calculate the back bearing of a line from its fore bearing.
  • Plot a compass traverse to scale and recognise an open and a closed traverse.

The prismatic compass gives you one number for each line: its bearing. Combined with the length of each line measured with a tape, these numbers are enough to draw the outline of a field, the course of a road or the path of a stream. This lesson shows how.

What a magnetic bearing is

The prismatic compass measures the horizontal angle of a line with reference to the magnetic north line. This angle, measured from magnetic north in the clockwise direction, is the magnetic bearing of the line. Because it can take any value from 0° to 360°, it is also called a whole-circle bearing. A series of connected survey lines is called a traverse, and each line is surveyed by its bearing and length.

Whole-circle bearings of the main directions
DirectionBearing
North0° (or 360°)
North-east45°
East90°
South-east135°
South180°
South-west225°
West270°
North-west315°

Magnetic north is not quite the same as true (geographical) north; the angle between them is the magnetic declination, which varies from place to place and slowly over time. For a small school survey we simply work with magnetic bearings, as the chapter does.

Fore bearing and back bearing

The bearing of line AB measured at A, looking towards B, is its fore bearing. The bearing of the same line measured at B, looking back to A, is its back bearing. The two directions are exactly opposite, so they differ by 180°.

Back bearing = fore bearing + 180° if the fore bearing is less than 180°; back bearing = fore bearing - 180° if it is 180° or more.

This gives a built-in check. In the field, a surveyor measures both bearings of each line. If they differ by exactly 180°, the readings are consistent. If not, one of the stations is probably affected by local attraction from nearby iron, or a reading was misread, and the line is checked again.

Worked example 1: back bearings

Find the back bearings of lines with fore bearings 60°, 215° and 180°. Working: 60° is less than 180°, so 60° + 180° = 240°. 215° is more than 180°, so 215° - 180° = 35°. 180° gives 180° - 180° = 0°. Answer: 240°, 35° and 0° (due north). Check: each pair differs by 180°.

Open and closed traverses

Two kinds of compass traverse

  • Open traverse
    • Starts and ends at different points
    • Used for a road, railway, river or canal
    • A meandering canal is divided into straight segments
    • No closing check on the plot itself
  • Closed traverse
    • Returns to the starting point
    • Used for the boundary of a field, plot or building
    • The plot should close on itself
    • A gap at the end shows the closing error

Plotting a traverse

  1. Enter each line in a table: line, fore bearing, back bearing, length.
  2. Choose a scale that fits the longest line on the paper.
  3. Mark the first station and draw a north line through it.
  4. With a protractor, measure the bearing clockwise from north and draw the line to scale.
  5. At the end of that line draw a new north line, parallel to the first, and repeat for the next line.
  6. For a closed traverse, see whether the last line returns to the start; a small gap is the closing error.

Worked example 2: a closed traverse

Made-up field book for a plot ABCD: AB bearing 90°, 40 m; BC bearing 180°, 30 m; CD bearing 270°, 40 m; DA bearing 0°, 30 m. Scale 1 cm to 10 m. Plot: from A draw 4 cm due east to B; from B draw 3 cm due south to C; from C draw 4 cm due west to D; from D draw 3 cm due north, which returns exactly to A. The plot is a rectangle 40 m by 30 m, so its area is 40 × 30 = 1,200 m². Check the back bearings: AB 90° → 270°; BC 180° → 0°; CD 270° → 90°; DA 0° → 180°, all differing by 180°.

Worked example 3: detecting an error

Made-up readings: line PQ, fore bearing 48°, back bearing 230°; line QR, fore bearing 112°, back bearing 292°. Expected back bearing of PQ = 48° + 180° = 228°, but 230° was read: a 2° difference, so P or Q may be affected by local attraction. Expected back bearing of QR = 112° + 180° = 292°, which matches. Since QR is consistent, the bearings at Q are probably correct, so the error is more likely at P, and PQ should be re-observed there.

Key takeaways: a magnetic bearing is the horizontal angle of a line measured clockwise from magnetic north, from 0° to 360°. Back bearing = fore bearing ± 180°, and a mismatch warns of local attraction or a misreading. An open traverse follows a road, river or canal; a closed traverse goes round a plot and should return to the start. Plot each line at its bearing from a fresh north line and to scale.

Check your understanding

  1. 1. A magnetic bearing is measured from magnetic north in which direction?

    1. Anticlockwise
    2. Clockwise
    3. Towards the nearest of north or south
    4. Vertically upwards
    Show answer

    Answer: B. The prismatic compass gives the horizontal angle of a line measured from magnetic north in the clockwise direction, from 0° to 360°.

  2. 2. The fore bearing of a line is 125°. Its back bearing is:

    1. 305°
    2. 55°
    3. 235°
    4. 145°
    Show answer

    Answer: A. 125° is less than 180°, so add 180°: 125° + 180° = 305°.

  3. 3. The fore bearing of a line is 300°. Its back bearing is:

    1. 480°
    2. 60°
    3. 210°
    4. 120°
    Show answer

    Answer: D. 300° is more than 180°, so subtract 180°: 300° - 180° = 120°.

  4. 4. Which survey would be an open traverse?

    1. The boundary of a school ground
    2. The walls of a rectangular building
    3. The course of a winding canal from a dam to a village
    4. The fence round a temple tank
    Show answer

    Answer: C. An open traverse starts and ends at different points, as along a canal, road or river. Boundaries of grounds, buildings and tanks return to the start and are closed traverses.

  5. 5. Made-up data: on a plot at 1 cm to 10 m, a line has bearing 270° and length 50 m. How is it drawn?

    1. 5 cm due east
    2. 50 cm due west
    3. 5 cm due south
    4. 5 cm due west
    Show answer

    Answer: D. A bearing of 270° is due west, and 50 m at 1 cm to 10 m is 50 ÷ 10 = 5 cm.

Sign in to keep track of the lessons you finish.

Next lesson → Final self-assessment: Surveying

Privacy · Terms · Refunds · Delivery