- Practice
- About 28 min
- 5 practice questions
Capacitors, distribution of charge, lightning arrester and Van de Graaff generator
Derive C = ε₀A/d and the energy ½CV², explain the effect of a dielectric with the battery disconnected or connected, combine capacitors in series and parallel, and explain action of points, the lightning arrester and the Van de Graaff generator.
If something looks wrong, please tell us.
By the end of this lesson you can
- Define capacitance C = Q/V and its unit, the farad.
- Derive C = ε₀A/d for a parallel plate capacitor and explain the effect of area and separation.
- Derive the stored energy U = Q²/2C = ½CV² and the energy density u = ½ε₀E².
- Explain what a dielectric does to Q, V, E, C and U with the battery disconnected and connected.
- Find equivalent capacitance in series and in parallel.
- Show that σr is constant for connected spheres and explain corona discharge, the lightning arrester and the Van de Graaff generator.
A capacitor stores electric charge and electrical energy. It consists of two conductors (usually plates) separated by a small gap. Capacitors are found in almost every electronic circuit: the condenser that gives a ceiling fan its starting torque, the flash unit of a camera and the defibrillator used during cardiac arrest all depend on them.
Capacitance
When a capacitor is connected to a battery of voltage V, the battery moves electrons from one plate to the other, leaving +Q on one plate and −Q on the other; the potential difference between the plates becomes equal to the battery's terminal voltage. The charge is proportional to the voltage, Q ∝ V, so Q = CV. The capacitance C = Q/V is the ratio of the charge on either plate to the potential difference between the plates. Its SI unit is C V⁻¹, the farad (F), named after Faraday. The farad is a large unit; practical capacitors range from microfarads (1 μF = 10⁻⁶ F) to picofarads (1 pF = 10⁻¹² F). The net charge of a capacitor is +Q − Q = 0; 'the charge stored' means the charge on one plate. Capacitors are made in many shapes and types, such as ceramic, tantalum and electrolytic.
Parallel plate capacitor
Two plates, each of area A, are separated by a distance d much smaller than the plate size. From the previous lesson, the field between two oppositely charged sheets is uniform: E = σ/ε₀ = Q/(Aε₀). The potential difference is V = Ed = Qd/(Aε₀). So C = Q/V = ε₀A/d. The capacitance grows with plate area (more room for charge at the same voltage) and grows as the gap shrinks. If the gap is narrowed while the battery stays connected, V = Ed of the capacitor briefly falls below the battery voltage, so more charge flows in until they are equal again; widening the gap sends charge back to the battery. A computer keyboard key works this way: pressing the key brings a movable plate closer to a fixed plate, the capacitance rises, and the circuit detects which key was pressed.
Worked example 1: a parallel plate capacitor
A capacitor has plates 10 cm × 20 cm, 1.0 mm apart in air, and is connected to a 50 V battery. Find C, the charge and the energy stored. Step 1: A = 0.10 × 0.20 = 0.020 m²; d = 1.0 × 10⁻³ m. Step 2: C = ε₀A/d = (8.85 × 10⁻¹² × 0.020)/(1.0 × 10⁻³) = 1.77 × 10⁻¹⁰ F = 177 pF. Step 3: Q = CV = 1.77 × 10⁻¹⁰ × 50 = 8.85 × 10⁻⁹ C = 8.85 nC. Step 4: U = ½CV² = 0.5 × 1.77 × 10⁻¹⁰ × 2500 ≈ 2.21 × 10⁻⁷ J.
Energy stored in a capacitor
While charging, the battery does work moving charge from one plate to the other against the growing voltage. Moving a small charge dQ when the voltage is V = Q/C needs dW = V dQ = (Q/C) dQ. The total work to charge from 0 to Q is W = ∫(Q/C) dQ = Q²/2C. This is stored as electrostatic potential energy: U = Q²/2C = ½CV² = ½QV. Where is the energy? Substituting C = ε₀A/d and V = Ed gives U = ½ε₀E² × (Ad), and Ad is the volume between the plates. So the energy density is u = ½ε₀E²: the energy is stored in the electric field itself. This result holds for the field of any charge arrangement. Because a capacitor keeps its charge for some time after the supply is removed, one should not touch the inside of an appliance such as an old television soon after switching it off.
Other uses named in the Tamil Nadu textbook: removing sparking in the ignition system of vehicle engines, and smoothing power fluctuations in power supplies and improving the efficiency of power transmission.
Effect of a dielectric
(i) Battery disconnected, then dielectric inserted. The charge Q₀ cannot change. The dielectric's polarisation reduces the field to E = E₀/εᵣ, so V = V₀/εᵣ, and C = εᵣC₀ = εᵣε₀A/d, written C = εA/d with ε = εᵣε₀. The energy U = Q₀²/2C = U₀/εᵣ decreases: the field pulls the dielectric into the gap, doing work on it.
(ii) Battery connected while the dielectric is inserted. The voltage V₀ is held fixed, so E = V₀/d also stays the same. Faraday found experimentally that the charge rises to Q = εᵣQ₀, so again C = εᵣC₀. Now the energy U = ½CV₀² = εᵣU₀ increases; the battery supplies the extra charge and energy.
| Quantity | Battery disconnected | Battery connected |
|---|---|---|
| Charge Q | Constant | Increases (εᵣQ₀) |
| Voltage V | Decreases (V₀/εᵣ) | Constant |
| Field E | Decreases (E₀/εᵣ) | Constant |
| Capacitance C | Increases (εᵣC₀) | Increases (εᵣC₀) |
| Energy U | Decreases (U₀/εᵣ) | Increases (εᵣU₀) |
Worked example 2: inserting a dielectric
The capacitor of example 1 (C₀ = 177 pF, Q₀ = 8.85 nC, V₀ = 50 V, U₀ = 2.21 × 10⁻⁷ J) is given a dielectric slab of εᵣ = 4 that fills the gap. (a) Battery disconnected first: C = 4 × 177 = 708 pF; Q stays 8.85 nC; V = 50/4 = 12.5 V; U = U₀/4 ≈ 5.5 × 10⁻⁸ J. (b) Battery kept connected: C = 708 pF; V stays 50 V; Q = CV = 708 × 10⁻¹² × 50 = 3.54 × 10⁻⁸ C = 35.4 nC; U = ½CV² = 0.5 × 708 × 10⁻¹² × 2500 ≈ 8.85 × 10⁻⁷ J, four times U₀.
Capacitors in series and in parallel
Series. When C₁, C₂ and C₃ are connected end to end across a battery V, the battery puts −Q on the last plate; by induction each capacitor ends up with the same charge Q on its plates. The voltages differ and add up to the battery voltage: V = V₁ + V₂ + V₃ = Q/C₁ + Q/C₂ + Q/C₃. Writing V = Q/C_S for the single equivalent capacitor: 1/C_S = 1/C₁ + 1/C₂ + 1/C₃. C_S is always less than the smallest capacitance in the chain.
Parallel. When C₁, C₂ and C₃ are each connected across the same battery, each has the same voltage V, but the charges differ: Q₁ = C₁V, Q₂ = C₂V, Q₃ = C₃V. By conservation of charge Q = Q₁ + Q₂ + Q₃, and with Q = C_PV: C_P = C₁ + C₂ + C₃. C_P is greater than the largest capacitance: in effect, the plate areas add.
Series and parallel capacitors
-
Series
- Same charge Q on each
- Voltages add: V = V₁ + V₂ + …
- 1/C_S = 1/C₁ + 1/C₂ + …
- C_S smaller than the smallest
-
Parallel
- Same voltage V across each
- Charges add: Q = Q₁ + Q₂ + …
- C_P = C₁ + C₂ + …
- C_P larger than the largest
Worked example 3: a combination
A 3 μF and a 6 μF capacitor in series are connected in parallel with a 4 μF capacitor, and the whole is joined to a 12 V battery. Step 1 (series pair): 1/C = 1/3 + 1/6 = 3/6, so C = 2 μF. Step 2 (with the 4 μF in parallel): C_eq = 2 + 4 = 6 μF. Step 3 (charges): total Q = 6 μF × 12 V = 72 μC. The 4 μF has the full 12 V, so Q = 48 μC. The series branch has 2 μF × 12 V = 24 μC on each of its capacitors. Step 4 (voltages in the branch): 24/3 = 8 V across the 3 μF and 24/6 = 4 V across the 6 μF; 8 + 4 = 12 V. Check: 48 + 24 = 72 μC.
Distribution of charge on a conductor
Join two conducting spheres of radii r₁ and r₂, far apart, by a thin wire and give them a total charge Q. Charge flows until both surfaces are at the same potential: kq₁/r₁ = kq₂/r₂, so q ∝ r. With q = 4πr²σ for each sphere, this gives σ₁r₁ = σ₂r₂, i.e. σr = constant: the surface charge density is inversely proportional to the radius. On one irregular conductor, too, charge crowds where the surface is most sharply curved (small radius of curvature), and the field there is strongest.
Worked example 4: two connected spheres
Spheres of radii 9 cm and 3 cm are joined by a long thin wire and share 120 nC. Step 1: q ∝ r, so q₁ : q₂ = 9 : 3 = 3 : 1, giving q₁ = 90 nC and q₂ = 30 nC. Step 2: σ₂/σ₁ = r₁/r₂ = 3: the smaller sphere has three times the charge density. Step 3: common potential V = kq₁/r₁ = (9 × 10⁹)(90 × 10⁻⁹)/0.09 = 810/0.09 = 9.0 × 10³ V. Check with the small sphere: (9 × 10⁹)(30 × 10⁻⁹)/0.03 = 270/0.03 = 9.0 × 10³ V.
Action of points and the lightning arrester
At a sharp point of a charged conductor the charge density, and so the field, can be large enough to ionise the surrounding air. Ions of the opposite sign are drawn to the point and neutralise its charge, while ions of the same sign are repelled. This leaking of charge from sharp points is called action of points or corona discharge. A lightning arrester (lightning conductor) uses it. A thick copper rod runs from a sharp spike above the top of a building down to a copper plate buried deep in the ground. When a negatively charged cloud passes overhead, it induces a large positive charge on the spike. Corona discharge from the spike ionises the air, and the positive ions neutralise part of the cloud's negative charge; the negative charge pushed to the spike passes down the rod safely to the Earth. The arrester does not stop lightning; it diverts it safely to the ground.
Van de Graaff generator
Designed by Robert Van de Graaff in 1929, this machine builds up a potential difference of several million volts using electrostatic induction and action of points. A large hollow metal sphere stands on an insulating column. An insulating belt (silk or rubber) runs over a pulley B at the centre of the sphere and a motor-driven pulley C at the bottom. Two comb-shaped conductors are fixed near the belt: comb D at the bottom, held at a positive potential of about 10⁴ V, and comb E at the top, connected to the inside of the sphere.
How the Van de Graaff generator charges its sphere
- Spraying charge at comb D The strong field at the points of D ionises the air; positive charges are pushed onto the belt.
- Belt carries charge up The motor-driven belt carries the positive charge to the top.
- Induction at comb E Comb E becomes negative and the sphere positive; corona discharge from E neutralises the belt's charge.
- Charge moves to the outside The positive charge spreads over the outer surface of the sphere.
- Belt returns almost neutral It goes down and picks up fresh positive charge at D.
Then back to step 1: Spraying charge at comb D
The potential rises until charge leaks into the air by ionisation, which limits it to about 10⁷ V; enclosing the machine in a steel chamber filled with gas at high pressure reduces the leakage. The high voltage is used to accelerate positive ions such as protons and deuterons for nuclear disintegration experiments. Since the field at the surface of a sphere of radius R at potential V is E = V/R, the largest potential is V_max = E_max R, where E_max is the dielectric strength of the surrounding air.
Worked example 5: the limit of a Van de Graaff generator
A small demonstration Van de Graaff generator has a sphere of radius 0.20 m in air (dielectric strength 3 × 10⁶ V m⁻¹). Step 1: at the surface E = kQ/R² and V = kQ/R, so V = ER. Step 2: V_max = E_max R = 3 × 10⁶ × 0.20 = 6 × 10⁵ V. A larger sphere can reach a higher potential.
C = Q/V; parallel plates C = ε₀A/d (εᵣ times more with a dielectric). U = ½CV² = Q²/2C; u = ½ε₀E². Series: 1/C_S = Σ1/C. Parallel: C_P = ΣC. Connected spheres: σr = constant.
Key takeaways
- Capacitance depends only on geometry and the medium: C = εᵣε₀A/d for parallel plates.
- Energy ½CV² is stored in the field, with energy density ½ε₀E².
- Dielectric with battery off: Q fixed, U falls. With battery on: V fixed, Q and U rise.
- Series capacitors share the same Q; parallel capacitors share the same V.
- Charge density is highest at sharp points; corona discharge drives the lightning arrester and the Van de Graaff generator.
Check your understanding
-
1. The plate area of a parallel plate capacitor is doubled and the separation is halved. Its capacitance becomes:
- the same
- 2 times
- half
- 4 times
Show answer
Answer: D. C = ε₀A/d. Doubling A doubles C, and halving d doubles it again: 2 × 2 = 4 times.
-
2. Three identical 6 μF capacitors are connected in series. The equivalent capacitance is:
- 18 μF
- 2 μF
- 6 μF
- 3 μF
Show answer
Answer: B. 1/C_S = 1/6 + 1/6 + 1/6 = 3/6 = 1/2, so C_S = 2 μF, less than any single capacitor. (18 μF would be the parallel value.)
-
3. A 10 μF capacitor is charged to 100 V. The energy stored is:
- 0.05 J
- 0.5 J
- 5 × 10⁻⁴ J
- 1 × 10⁻³ J
Show answer
Answer: A. U = ½CV² = 0.5 × 10 × 10⁻⁶ × (100)² = 0.5 × 10⁻⁵ × 10⁴ = 0.05 J.
-
4. A charged capacitor is disconnected from its battery and a dielectric slab is then pushed in between the plates. Which statement is correct?
- Charge increases and energy increases
- Voltage stays the same and charge increases
- Charge stays the same and energy decreases
- Capacitance decreases
Show answer
Answer: C. With the battery removed, Q cannot change. C rises to εᵣC₀, so V = Q/C falls and U = Q²/2C falls to U₀/εᵣ. The field pulls the slab in, doing work on it.
-
5. A lightning arrester works on the principle of:
- electrostatic shielding
- magnetic induction
- dielectric polarisation
- action of points (corona discharge)
Show answer
Answer: D. The sharp spike on top acquires a high induced charge density; the strong field ionises the air (corona discharge), neutralising part of the cloud's charge and leading the rest safely to the Earth.
Sign in to keep track of the lessons you finish.