• Foundation
  • About 14 min
  • 5 practice questions

Planning a test: objectives, blueprint and weightage

Explain why a test needs a plan, build a simple blueprint (table of specification) that spreads marks over content and objectives, and check that its totals agree.

If something looks wrong, please tell us.

A good test does not begin with writing questions. It begins with a plan. Without a plan, a teacher tends to ask more about the topic taught last, or about the topics that are easy to ask about, and the test then does not match what was taught. The plan that prevents this is called a blueprint, also known as a table of specification. This lesson shows what a blueprint is and how to build one.

Why a test needs a plan

Recall the quality called validity from an earlier lesson: a test is valid when it measures what it is meant to measure. A test that leaves out a whole unit, or that asks only for facts when the teaching aimed at understanding, cannot be valid for the whole course. A blueprint helps because it fixes in advance how the marks will be spread. It improves the match between the teaching and the test, which is called content validity.

Steps in planning

  1. Decide the purpose of the test: diagnosis, a check during teaching, or a final report.
  2. List the objectives to be tested. Many blueprints use three simple groups, knowledge (remembering), understanding (explaining in one's own words) and application (using in a new situation).
  3. List the content units that were taught, and decide how many marks each deserves.
  4. Decide how many marks go to each objective.
  5. Fill a grid that crosses content with objectives, so that every cell shows its marks.
  6. Write items to fit the grid, then review the test against the grid.

Deciding weightage

The usual rule for content weightage is that marks follow teaching time, because time shows how important the unit was in the course. Suppose the 30-mark test is on four units that took 5, 4, 3 and 3 periods, so 15 periods in all. The marks per period are 30 ÷ 15 = 2. Unit 1 gets 5 × 2 = 10 marks, unit 2 gets 4 × 2 = 8, and units 3 and 4 get 3 × 2 = 6 each. The total is 10 + 8 + 6 + 6 = 30. These numbers are illustrative; each school or teacher decides the actual weightage.

For objectives, suppose the teacher decides on 40% for knowledge, 40% for understanding and 20% for application. Of 30 marks, that is 12, 12 and 6.

A blueprint grid

A 30-mark blueprint (illustrative)
Content unitKnowledgeUnderstandingApplicationTotal
Unit 144210
Unit 23328
Unit 33216
Unit 42316
Total1212630

Check the grid in two ways. The rows must add up to the marks planned for each unit (10, 8, 6, 6). The columns must add up to the marks planned for each objective (12, 12, 6). When both checks agree with the grand total of 30, the grid is consistent.

Worked example 1

Situation: a 40-mark test covers a unit taught in 3 of the 20 periods of the course. Step 1: the share of teaching time is 3 ÷ 20. Step 2: the marks are 3 ÷ 20 × 40 = 6. Answer: the unit should get about 6 marks.

Worked example 2

Situation: in the blueprint above, one cell of the last row is missing. The Application column shows 2, 2, 1 and an unknown number for unit 4, and the planned total for Application is 6. Step 1: the known numbers add up to 2 + 2 + 1 = 5. Step 2: the missing number is 6 − 5 = 1. Step 3: check the row: 2 + 3 + 1 = 6, which is the planned total for unit 4. Answer: the missing cell is 1.

Purpose, objectives, content weightage, objective weightage, grid, then items. Marks follow teaching time, and the rows and columns of the grid must both add up to the total.

Key takeaways

  • A blueprint spreads marks over content units and objectives before any question is written.
  • It supports content validity by matching the test to what was taught.
  • Content marks usually follow teaching time.
  • Rows and columns of the blueprint must add up to the same total.

Check your understanding

  1. 1. The main purpose of a blueprint is to:

    1. decide how long each student may take over it
    2. ensure planned coverage of content and objectives
    3. make the right answers easier to guess
    4. replace the marking scheme with a list
    Show answer

    Answer: B. A blueprint plans in advance how marks are spread over content and objectives, so the test matches the teaching. It does not fix the time, help guessing or replace the marking scheme.

  2. 2. In a 40-mark test, a unit that took 3 of the 20 periods should get about:

    1. 3 marks
    2. 8 marks
    3. 12 marks
    4. 6 marks
    Show answer

    Answer: D. The share is 3/20, and 3/20 × 40 = 6 marks.

  3. 3. A 30-mark blueprint gives 40% of the marks to knowledge. How many marks is that?

    1. 12
    2. 10
    3. 14
    4. 16
    Show answer

    Answer: A. 40% of 30 = 0.4 × 30 = 12 marks.

  4. 4. Which step comes right after deciding the purpose of the test?

    1. writing the questions
    2. marking the answer sheets
    3. listing the objectives to be tested
    4. reporting the results to parents
    Show answer

    Answer: C. After the purpose, the teacher lists the objectives to be tested, then plans content and builds the grid. Items are written later.

  5. 5. A test has many questions on one unit and none on another unit taught for the same time. Which quality suffers most?

    1. objectivity, because marking is slower
    2. usability, because the paper is longer
    3. speed, because there are more questions
    4. validity, as coverage of the content is uneven
    Show answer

    Answer: D. Leaving out a unit means the test does not measure the whole course, so content validity falls. The test could still be marked objectively.

Privacy · Terms · Refunds · Delivery