Revision notes

Chapter 5 Work, Energy and Power: Foundation

The key points, rules to remember, tables and diagrams from all 5 lessons, on one page for quick revision. To keep a copy, use your browser's Print and choose "Save as PDF".

Lesson 1

The scalar product and work done by a constant force

A·B = AB cos θ = AₓBₓ + A_yB_y + A_zB_z. A·B = 0 for perpendicular vectors.

The sign of work depends on the angle θ between F and d

  • Positive work (0° ≤ θ < 90°)
    • Force has a component along the motion
    • Example: pulling a trolley forward
    • Example: gravity on a falling ball
  • Zero work (θ = 90°, or d = 0, or F = 0)
    • Pushing a fixed wall: no displacement
    • Holding a load still: no displacement
    • Gravity on a body sliding on a level floor
    • Centripetal force in uniform circular motion
  • Negative work (90° < θ ≤ 180°)
    • Force opposes the motion
    • Friction on a sliding block (θ = 180°)
    • Gravity on a ball thrown upward
  • A·B = AB cos θ is a scalar; in components it is AₓBₓ + A_yB_y + A_zB_z.
  • Work W = F·d = Fd cos θ, measured in joules; dimensions [M L² T⁻²].
  • No work is done if the displacement is zero, the force is zero or they are perpendicular.
  • Friction usually does negative work; third-law partners need not do equal work.
Read the full lesson

Lesson 2

Kinetic energy and the work-energy theorem

Work-energy theorem: the change in kinetic energy of a particle equals the work done on it by the net force, K_f − K_i = W_net.

Work done by a varying force

  1. Split the path Divide the displacement into many small steps Δx.
  2. Treat F as constant on each step Work on each step ≈ F(x) Δx, a thin strip of area.
  3. Add the strips Total work ≈ Σ F(x) Δx.
  4. Take the limit Δx → 0 W = ∫ F dx = area under the F-x graph.
  • K = ½mv²; doubling speed quadruples kinetic energy.
  • W_net = K_f − K_i holds for constant and variable forces alike.
  • Work by a variable force is ∫F dx, the signed area under the F-x graph.
  • The theorem is a scalar, time-free shortcut; it does not replace F = ma.
Read the full lesson

Lesson 3

Potential energy and the conservation of mechanical energy

If only conservative forces do work, the total mechanical energy K + V of a system stays constant.

Energy changes of a ball tossed up and caught (no air resistance)

  1. Launch All kinetic energy, ½mv₀²; potential energy taken as zero.
  2. Rising Kinetic energy turns into potential energy mgh.
  3. Top All potential energy, mgh_max; kinetic energy zero.
  4. Falling Potential energy turns back into kinetic energy.

Then back to step 1: Launch

  • Potential energy is stored energy of position or configuration; near Earth, V = mgh.
  • For a conservative force F = −dV/dx, and its work is path-independent (zero round a closed path).
  • With only conservative forces, K + V = constant.
  • With friction, E_f − E_i = W_nc, which is negative.
Read the full lesson

Lesson 4

Potential energy of a spring, and power

Spring potential energy V(x) = ½kx², for a stretch or compression x. Check: −dV/dx = −kx, the spring force.

Energy exchange in a block-spring system

  1. Released at x = +xₘ All energy is spring potential energy ½kxₘ².
  2. Passing x = 0 All kinetic energy; speed is maximum, xₘ√(k/m).
  3. At x = −xₘ Momentarily at rest; all potential energy again.
  4. Back through x = 0 Kinetic energy maximum again, moving the other way.

Then back to step 1: Released at x = +xₘ

P = dW/dt = F·v. 1 W = 1 J s⁻¹; 1 hp = 746 W; 1 kWh = 3.6 × 10⁶ J (energy).

  • Hooke's law F = −kx; the spring stores V = ½kx² and is a conservative force.
  • In a block-spring system K + ½kx² is constant; maximum speed xₘ√(k/m) at x = 0.
  • Power P = dW/dt = F·v, in watts; 1 hp = 746 W.
  • The kWh measures energy: 1 kWh = 3.6 × 10⁶ J.
Read the full lesson

Lesson 5

Collisions: elastic and inelastic, in one and two dimensions

Kinds of collision

  • Elastic
    • Momentum conserved
    • Total kinetic energy after = before
    • Bodies regain shape fully; e.g. ideal billiard balls
  • Inelastic
    • Momentum conserved
    • Some kinetic energy lost
    • The most common real case
  • Completely (perfectly) inelastic
    • Momentum conserved
    • Bodies stick together and move as one
    • Greatest possible loss of kinetic energy

Elastic, m₂ initially at rest: v₁f = (m₁ − m₂)v₁ᵢ/(m₁ + m₂) and v₂f = 2m₁v₁ᵢ/(m₁ + m₂).

  • Momentum is conserved in all collisions; kinetic energy only in elastic ones.
  • Sticking together: v_f = m₁v₁ᵢ/(m₁ + m₂), with the greatest loss of kinetic energy.
  • Elastic, target at rest: v₁f = (m₁ − m₂)v₁ᵢ/(m₁ + m₂), v₂f = 2m₁v₁ᵢ/(m₁ + m₂).
  • Equal masses, elastic glancing collision with one at rest: they separate at 90°.
Read the full lesson

Privacy · Terms · Refunds · Delivery