• Foundation
  • About 20 min
  • 5 practice questions

Speed of a travelling wave: strings, solids and the speed of sound

Derive v = ω/k = νλ, find the speed of waves on a stretched string (√(T/μ)) and of longitudinal waves (√(B/ρ), √(Y/ρ)), and explain Newton's formula for sound and Laplace's correction.

If something looks wrong, please tell us.

By the end of this lesson you can

  • Derive v = ω/k = νλ by following a point of fixed phase.
  • Use dimensional analysis to obtain v = √(T/μ) for a string and v = √(B/ρ) for sound.
  • Explain why sound is faster in solids and liquids than in gases.
  • Compare Newton's formula v = √(P/ρ) with Laplace's corrected formula v = √(γP/ρ).

How fast does a wave move, and what decides its speed? For mechanical waves the answer always comes from two properties of the medium: how strongly it pulls back when disturbed (an elastic property) and how much inertia it has (a density).

Speed of a progressive wave

Follow a crest, or any point of fixed phase. In a short time Δt the whole pattern shifts by Δx, so the speed is Δx/Δt. A fixed-phase point has kx − ωt = constant, so k(x + Δx) − ω(t + Δt) = kx − ωt, giving kΔx = ωΔt and

v = ω/k = (2πν)/(2π/λ) = νλ = λ/T. In one period the wave advances one wavelength.

The medium fixes the speed; the source fixes the frequency; then λ = v/ν. Transverse and longitudinal waves in the same medium generally have different speeds.

Transverse waves on a stretched string

The restoring force is the tension T, and the inertia is the linear mass density μ = mass/length, with dimensions [ML⁻¹]. Tension has dimensions [MLT⁻²]. The ratio T/μ has dimensions [MLT⁻²]/[ML⁻¹] = [L²T⁻²], the square of a speed. So v = C√(T/μ), where dimensional analysis cannot find the constant C; an exact derivation using Newton's laws (beyond this book) gives C = 1:

Speed of a transverse wave on a string: v = √(T/μ). It depends only on the tension and the mass per unit length, not on the frequency or wavelength.

Worked example 1: a stretched wire

A wire 1.0 m long has a mass of 4.0 g and is under a tension of 100 N. μ = 4.0 × 10⁻³ kg/1.0 m = 4.0 × 10⁻³ kg m⁻¹. v = √(T/μ) = √(100/4.0 × 10⁻³) = √(2.5 × 10⁴) ≈ 158 m s⁻¹. Quadrupling the tension would double the speed.

Longitudinal waves: the speed of sound

For compressions and rarefactions the elastic property is the bulk modulus B = −ΔP/(ΔV/V) (Chapter 8) and the inertia is the density ρ. B/ρ has dimensions [ML⁻¹T⁻²]/[ML⁻³] = [L²T⁻²], and the exact result (C = 1) is v = √(B/ρ). In a long solid bar, sideways expansion is negligible and the relevant modulus is Young's modulus: v = √(Y/ρ). Solids and liquids are denser than gases, but their elastic moduli are larger by a much bigger factor, so sound travels faster in them than in gases.

Worked example 2: sound in water and in steel

Water: B = 2.2 × 10⁹ Pa, ρ = 1000 kg m⁻³. v = √(2.2 × 10⁹/1000) = √(2.2 × 10⁶) ≈ 1.48 × 10³ m s⁻¹. Steel bar: Y = 2.0 × 10¹¹ Pa, ρ = 7.8 × 10³ kg m⁻³. v = √(2.0 × 10¹¹/7.8 × 10³) = √(2.56 × 10⁷) ≈ 5.1 × 10³ m s⁻¹. Both are many times the speed in air.

Newton's formula and Laplace's correction

  1. Newton assumed the compressions and rarefactions in a gas are isothermal. From PV = NkBT at constant T, VΔP + PΔV = 0, so −ΔP/(ΔV/V) = P: the bulk modulus is B = P.
  2. Newton's formula: v = √(P/ρ). For air this gives about 15% less than the measured speed.
  3. Laplace pointed out that the pressure changes in sound are so fast that there is no time for heat to flow, so they are adiabatic. Then PV^γ = constant; differentiating, γPV^(γ−1)ΔV + V^γΔP = 0, so the adiabatic bulk modulus is B = γP.
  4. Corrected (Laplace) formula: v = √(γP/ρ). For air γ ≈ 1.4 (= 7/5), which brings the value into agreement with experiment.

Newton: v = √(P/ρ) (isothermal, too low). Laplace: v = √(γP/ρ) (adiabatic, agrees with measurement).

Worked example 3: sound in air at 300 K

Estimate the speed of sound in air at 300 K and 1.013 × 10⁵ Pa (molar mass of air 0.029 kg mol⁻¹, γ = 1.4). Density: ρ = PM₀/(RT) = 1.013 × 10⁵ × 0.029/(8.31 × 300) ≈ 1.18 kg m⁻³. Newton: v = √(1.013 × 10⁵/1.18) ≈ 293 m s⁻¹. Laplace: v = √(1.4) × 293 ≈ 347 m s⁻¹, close to measured values near this temperature. Since ρ = PM₀/(RT), the formula can also be written v = √(γRT/M₀): at a fixed pressure the speed of sound in a gas grows as √T.

From medium to wave speed

  1. Identify the restoring property Tension T, bulk modulus B, or Young's modulus Y.
  2. Identify the inertia Linear density μ for a string, density ρ otherwise.
  3. Form the speed √(T/μ), √(B/ρ), √(Y/ρ); for gases B = γP.
  4. Use the source frequency λ = v/ν.

Key takeaways

  • v = ω/k = νλ for every progressive wave.
  • String: v = √(T/μ). Fluid: v = √(B/ρ). Solid bar: v = √(Y/ρ).
  • Sound is faster in solids and liquids because their moduli are much larger relative to their densities.
  • In a gas the changes are adiabatic: v = √(γP/ρ) (Laplace), not √(P/ρ) (Newton).

Check your understanding

  1. 1. A sound wave of frequency 500 Hz has a wavelength of 0.68 m in air. What is its speed?

    1. 735 m s⁻¹
    2. 340 m s⁻¹
    3. 0.0014 m s⁻¹
    4. 680 m s⁻¹
    Show answer

    Answer: B. v = νλ = 500 × 0.68 = 340 m s⁻¹.

  2. 2. The tension in a stretched string is made four times larger. The speed of transverse waves on it becomes

    1. four times as large
    2. half as large
    3. twice as large
    4. unchanged
    Show answer

    Answer: C. v = √(T/μ), so v ∝ √T. Multiplying T by 4 multiplies v by √4 = 2.

  3. 3. A string with linear mass density 0.010 kg m⁻¹ is under a tension of 90 N. What is the speed of transverse waves on it?

    1. 9.0 m s⁻¹
    2. 900 m s⁻¹
    3. 0.9 m s⁻¹
    4. 95 m s⁻¹
    Show answer

    Answer: D. v = √(T/μ) = √(90/0.010) = √9000 ≈ 94.9 m s⁻¹, about 95 m s⁻¹.

  4. 4. Why did Laplace correct Newton's formula for the speed of sound in a gas?

    1. Newton used the wrong density of air
    2. The compressions and rarefactions are too fast for heat to flow, so they are adiabatic and the bulk modulus is γP, not P
    3. Sound waves in air are transverse
    4. The speed of sound does not depend on pressure
    Show answer

    Answer: B. Newton assumed isothermal changes (B = P), which gives a speed about 15% too low. The changes are actually adiabatic, for which B = γP, giving v = √(γP/ρ).

  5. 5. Why does sound travel faster in steel than in air, although steel is far denser?

    1. Steel's elastic modulus is larger than air's by a much bigger factor than its density is
    2. Sound is transverse in steel
    3. Steel is a better conductor of heat
    4. The frequency of sound increases in steel
    Show answer

    Answer: A. v = √(modulus/density). Steel is a few thousand times denser than air, but its modulus is roughly a million times larger, so the ratio, and hence the speed, is much greater.

Privacy · Terms · Refunds · Delivery