Revision notes

Chapter 3 Electricity: Circuits and their Components: Foundation

The key points, rules to remember, tables and diagrams from all 5 lessons, on one page for quick revision. To keep a copy, use your browser's Print and choose "Save as PDF".

Lesson 1

Uses of electricity, safety, electric cells and batteries

Uses of electricity

  • Lighting
    • Homes, offices, streets, markets
  • Cooking
    • Electric kettle, mixer grinder, toaster, oven
  • Heating and cooling
    • Fan, geyser, room heater, refrigerator, air conditioner
  • Communication and entertainment
    • Mobile phone, internet, radio, television
  • Transport
    • Electric trains, lifts, escalators, electric scooters
  • Other work
    • Water pumps, cranes, computers, hospital machines
One way of grouping; you can group the same uses in other ways too

Never experiment with the electricity supply from wall sockets or generators. Use only cells or batteries, like those in torches, clocks and remotes, for experiments.

Terminals of a common torch cell
PartWhat it looks likeName
One endSmall metal cap that sticks outPositive terminal (+)
Other endFlat metal discNegative terminal (−)

Cells joined to make a battery

  1. Cell 1 Its + terminal touches the − terminal of cell 2.
  2. Cell 2 Its + terminal touches the − terminal of cell 3.
  3. Cell 3 The free + of the last cell and the free − of the first cell are the battery's terminals.

Key takeaways: electricity is used for lighting, cooking, heating and cooling, communication, transport and much more. Experiment only with cells and batteries, never with the mains. A cell has a positive terminal (metal cap) and a negative terminal (flat disc). Cells joined + to − make a battery, which gives more energy or works for longer.

Read the full lesson

Lesson 2

Electric lamps: the incandescent lamp and the LED

Parts of an incandescent torch lamp

  • Glass bulb
    • Protects the filament
  • Filament
    • Very thin wire
    • Gets hot and glows
  • Two thick wires
    • Support the filament
    • Join it to the terminals
  • Terminals
    • Metal case at the side of the base
    • Metal tip at the centre of the base
  • Insulator
    • Keeps the two terminals apart

Incandescent lamp versus LED

  • Incandescent lamp
    • Has a filament that gets hot and glows
    • Terminals: metal case and metal tip
    • Glows whichever way it is connected
    • Stops working if the filament breaks
  • LED
    • No filament
    • Longer leg +, shorter leg −
    • Glows only when connected the right way
    • Comes in many colours

An LED lets current pass in one direction only: longer leg to the + side of the battery, shorter leg to the − side.

Finding faults in a torch
CheckPossible problemHow to test
CellsCells used up, or placed + to + or − to −Try new cells; check each is placed + to −
Lamp (incandescent)Fused: broken filamentLook for a broken wire inside the bulb; try a lamp that works
Lamp (LED)Connected the wrong way roundSwap the connections and test again
ConnectionsA loose contact or a gapPress the contacts firmly; check the spring

Key takeaways: in an incandescent lamp, current makes a thin filament hot enough to glow; its terminals are the metal case and the metal tip, and a broken filament means a fused lamp. An LED has no filament; its longer leg is positive and its shorter leg negative, and it glows only when connected the right way round.

Read the full lesson

Lesson 3

The electric circuit and the switch

A closed circuit

  1. Positive terminal of the cell Current leaves the cell here.
  2. Wire Carries current to the lamp.
  3. Lamp Current passes through the filament, which glows.
  4. Wire Carries current back.
  5. Negative terminal of the cell Current returns to the cell; the path is complete.

Then back to step 1: Positive terminal of the cell

A lamp glows only when it is part of a closed circuit: a complete path from one terminal of the cell, through the lamp, to the other terminal.

Predicting before testing
ArrangementPath complete?Lamp glows?
Wire from + of cell to metal tip; wire from − of cell to metal caseYesYes
Both wires from the lamp joined to the + terminal onlyNoNo
Wire from + to the tip; − terminal left unconnectedNoNo
Both wires touching the metal case onlyNo (current does not pass through the filament)No

Switch positions

  • ON (closed circuit)
    • The safety pin touches both drawing pins
    • The gap is closed
    • Current flows and the lamp glows
  • OFF (open circuit)
    • The safety pin does not touch the second pin
    • There is an air gap
    • No current; the lamp does not glow

Key takeaways: an electric circuit is a complete path from one terminal of a cell, through the device, to the other terminal. Current is taken to flow from + to − in the outside circuit. A switch completes the circuit when ON (closed) and breaks it when OFF (open), and it can be placed anywhere in the circuit. The cell, not the switch, is the source of electricity.

Read the full lesson

Lesson 4

Circuit diagrams and symbols

Common circuit symbols (as described in words)
ComponentHow its symbol is drawnWhat to remember
Electric cellTwo parallel lines: one long and thin, one short and thickLong line = positive (+), short line = negative (−)
BatteryTwo or more cell symbols joined in a rowLong line of one cell next to the short line of the next
Electric lampA circle with a cross inside, or a small coil inside a circleShows a device that gives light
LEDA triangle pointing at a short bar, with two small arrows pointing outwardsTriangle points the way current can flow; arrows show light coming out
Switch ONA line with a small lever lying flat and closing the gapClosed circuit
Switch OFFThe same lever tilted up, leaving a gapOpen circuit
WireA straight lineJoins components

In the symbol for a cell, the longer line is the positive terminal and the shorter line is the negative terminal.

Torch circuit, in the order current travels

  1. Battery (+) Two cells joined + to −.
  2. Switch ON closes the gap.
  3. Lamp Filament glows.
  4. Battery (−) Back to the battery to complete the loop.

Then back to step 1: Battery (+)

CircuitWhat the diagram showsGlows?
PCell, closed switch, lamp, all in one loopYes
QCell, open switch, lamp in one loopNo: the switch leaves a gap
RBattery, closed switch, LED with its triangle pointing from the + side towards the − sideYes
SBattery, closed switch, LED with its triangle pointing from the − side towards the + sideNo: the LED is reversed

Key takeaways: a circuit diagram represents a circuit using symbols. In a cell symbol the long line is + and the short line is −; a battery is cells drawn in a row. The LED symbol's triangle shows the one direction current can pass, and its arrows show light. A switch symbol shows a closed or open gap. Trace a diagram from + back to − to predict whether a device will work.

Read the full lesson

Lesson 5

Conductors and insulators, and staying safe

Testing a material

  1. Check the tester Touch the free ends together; the lamp must glow.
  2. Touch both ends to the object Keep the two wire ends apart.
  3. Observe the lamp Glows: current passes. Does not glow: it does not.
  4. Record and classify Conductor or insulator.
Typical results with a cell-and-lamp tester
ObjectMaterialLamp glows?Conductor or insulator
KeyMetalYesConductor
Aluminium foilMetalYesConductor
Steel spoonMetalYesConductor
Pencil leadGraphite (a form of carbon)YesConductor
Plastic scalePlasticNoInsulator
EraserRubberNoInsulator
Glass bangleGlassNoInsulator
Wooden stickDry woodNoInsulator
CandleWaxNoInsulator

Conductors let electric current pass easily; insulators do not. Metals are good conductors; plastic, rubber, glass, dry wood and ceramics are insulators.

Two kinds of electric supply

  • From cells and batteries
    • Direct current (DC)
    • Flows one way
    • Powers small devices: torches, clocks, remotes, phones
  • From the wall socket
    • Alternating current (AC)
    • Comes from power stations
    • Runs larger appliances; dangerous to experiment with

Key takeaways: a simple cell-and-lamp tester shows which materials conduct electricity. Metals are conductors, and copper is used for wires because it conducts well and costs less than silver or gold. Plastic, rubber, glass, dry wood and ceramics are insulators and are used for covers. Our body conducts electricity, so the mains is never used for experiments, hands must be dry and damaged wires must be replaced.

Read the full lesson

Privacy · Terms · Refunds · Delivery